Instruction Manual ZagatO Macchina da Caffe’ Espresso coffee machine Maquina para café exprés machine a café espress Espresso Kaffeemaschinen We congratulate you for having bought this top-quality coffee machine and thank you for choosing Zagato. Before operating the coffee machine , we recommend to read the following instructions thoroughly which explains how to install and use the unit.
ZagatO Index Safety Indications 3 General Safety instructions Machine Description Technical Data Installation 4 5 6 ! Calibration Use and Programming 7 8-11 Coffee pouring Pre infusion Alarm conditions Programming Dispensing hot water Dispensing steam Cleaning and Maintenance 12-13 Filter and filter holder Showers Steam nozzle Group heads (back flushing) Machine maintenance NOTE ! Operations essential to guarantee efficient function.
ZagatO Safety indications General safety instructions Do not touch the machine with wet hands and feet! How to use the instructions These instructions cannot anticipate every possible use of the unit. For further information or question concerning specific situations or problem , please contact the local dealer or manufacturer directly.
ZagatO Machine Description Volumetrica series 12 8 8 12 11 10 2.5 1.5 1 0 7 1 2 2.5 1.5 1 1 0 2 5 9 0 3 4 4 6 NOTE ! 1 Boiler level-check window 7 Hot water dispensing 2 Boiler pressure gauge 8 Steam Knob 3 Pump gauge 9 Machine main switch 4 Steam nozzle 10 Internal programming switch 5 2-cup filter 11 Hot water knob 6 Adjustable feet 12 Push button panels Positioning Place the unit on a level surface.
ZagatO Technical Data Model Zagato 1gr Volumetrica Zagato 2gr Volumetrica Zagato 3gr Volumetrica Power 11AMP: 240V 50/60HZ; 17AMP:240V 50/60HZ 25AMP:240V 50/60HZ 2400W 3900W 6000W Water pres min./max.
ZagatO Installation TEC Preparation of the machine The preparation of the coffee machine and its installation must be performed by qualified staff. !! WARNING Use of the machine without all the installation operations having been carried out by technical personnel could damage it seriously. Starting the machine Open the water tap of the water mains and of the softener / water filter.
ZagatO Calibration TEC Pressure switch adjustment The pressure switch shown in the figure acts to keep the boiler pressure constant by engaging or de-activating the electrical heating resistance. This pressure switch is already calibrated to 1.1-1.
ZagatO Use and programming Coffee Pouring On pressing the corresponding button T1-T2-T3 or T4, the corresponding delivery solenoid valves are activated for the time necessary to obtain the required amount of product as previously programmed (volumetric check). The delivery in progress may be suspended before actually reaching the desired programmed product quantity by pressing button T5 Stop. It is also possible to obtain simultaneous coffee delivery from all the machine groups.
ZagatO Use and programming NOTE ! 1 2 IMPORTANT The programming of every dose must be done with ground coffee and not with previously used grounds. With machines having two or three groups, by first programming the right-hand buttons panel the others are automatically programmed. It is however both possible and advisable to program the push button panels independently, always starting from the right-hand button panel.
ZagatO Use and programming 3 4 Light Programming with pre infusion (Buttons must flash, if not press T5) Flash Put the coffee cup under the dispensing spout. T1 4 T1 Press the button to be programmed and hold for as long as you want the preinfusion. (Aprox. from 1 to 3 sec) T3 T2 T3 T2 T4 T4 T5 T5 Wait up to 2 sec. (Infusion time) 5 Press and hold the same button again until the desired dose is obtained. 6 Press button T5 to confirm.
ZagatO Use and programming Dispensing Steam To dispense steam , turn the tap knob (S) counter -clockwise : the amount of steam which comes out of the nozzle will be proportional to the opening of the tap. The steam nozzles must be cleaned immediately after use in order to prevent the risk of the formation of any scale which may block the holes and to ensure that any drinks made subsequently do not absorb any unpleasant odors.
Filter and filter holder The filters (F) and the relative filter holders (G) must be cleaned daily in hot water. The best thing to do is to let them soak in hot water overnight so that the fatty coffee deposit can dissolve. It is advisable to special coffee machines detergent to the water , and then to rinse everything off with water.
ZagatO Cleaning and maintenance Group heads (back flushing) The cleaning of the internal parts of the delivery groups is to be performed weekly in the following manner: A Insert the rubber blind filters (A) in the filter-holders Pour a teaspoon of a suitable detergent powder on each of the blind filters and attach the filter-holders to the groups. Using the right-hand button panel, press at the same time button T1 and T5 to activate the automatic cleaning cycle. The buttons T2 ,T3, T4 will light up.
ZagatO Trouble Shooting DEFECT CAUSE SOLUTION No power to machine 1 Main switch off 2 Machine switch off 3 Incorrect electrical mains connection 1 Switch mains on 2 Switch machine to 2 3 Contact specialized personnel to check connection No water in boiler 1 Main tap closed 2 Clogged pump, filter 3 Motor/pump faulty 1 Open the mains tap 2 Replace water filter 3 Contact specialized personnel No water from group head 1 Main tap closed 2 Motor/pump faulty 3 Clogged jets 4 Electronic board faulty 5 So
ZagatO Trouble Shooting DEFECT CAUSE SOLUTION Coffee delivered cold 1 Lime scale present on the heat exchanger or element 2 Oxidized pressure switch contacts 3 Defective electrical connection 4 Partially burnt out element 1 Contact specialized personnel Coffee delivered too hot 1 Incorrect pressure switch calibration 1 Contact specialized personnel All buttons lit 1 Safety device activated 2 No water in mains 3 Coffee is too fine 1 Turn the machine off and back on 2 open the water mains tap 3 Ad
ZagatO About the manual The manufacturer reserves the right to add additional details to the product. We guarantee that these instructions reflect the actual state of the product at the moment of its sale in the market. We also would like to use this occasion to invite you to offer suggestions regarding possible improvements of this product or the instructions themselves.