Save This Manual for Future Reference Gas Log Splitter Operator’s Manual MODEL NUMBER YS2565 YS2865 YS3065 YS3567 SERIAL NUMBER PURCHASE DATE Both model number and serial number may be found on the main label. You should record both of them in a safe place for future use.
Your new YARDMAX ® gas log splitter offers quality construction, and is easy and safe to operate. With proper use and care, it is designed to give you many years of dependable service.
Gas Log Splitter » Operator’s Manual MODEL AND SERIAL NUMBERS Carefully read through this entire operator's manual before using your new unit. Pay attention to all cautions and warnings. This unit is a gasoline engine driven hydraulic log splitter. It is designed to split wood logs for use as firewood for a stove or fireplace. This log splitter will only split logs lengthwise with the grain. Record the model and serial number as well as date and place of purchase for future reference.
SUPPORT Have questions about your YARDMAX equipment? Call us at 847-327-0566 or 844-YARDMAX, email us at support@yardmax.com, or contact us via your favorite social media site. SPECIFICATIONS Model # YS2565 YS2865 YS3065 YS3567 Splitting Force* 25 Ton 28 Ton 30 Ton 35 Ton 25.5" 25.5" 25.5" 26" Log Capacity Engine Briggs & Stratton Briggs & Stratton 208 cc 306 cc 9.5 ft- lb 14.5 ft- lb Fuel Capacity 0.80 Gallon 1.40 Gallon Engine Oil Capacity 0.16 Gallon 0.
Gas Log Splitter » Operator’s Manual Model # YS2565 YS2865 YS3065 YS3567 Pump Size 14 GPM 14 GPM 17 GPM 17 GPM 4" 4.5" 4.5" 5" Hydraulic Cylinder Stroke 23.5" 23.5" 23.5" 23.5" Hydraulic Rod Diameter 1.75" 1.75" 1.75" 2" 9.7 seconds 13.2 seconds 10.9 seconds 12.8 seconds 4.0 Gallon 4.3 Gallon 4.3 Gallon 4.
SYMBOLS The rating plate on your machine may show symbols. These represent important information about the product or instructions on its use. Never remove partially split wood from the wedge with your hands. Fingers may become trapped between the split wood. Read these instructions carefully. Keep hands and feet away from moving parts. Moving parts can crush or cut. Wear eye protection. Wear hearing protection. Wear protective gloves. Keep hands away from the log stripper.
Gas Log Splitter » Operator’s Manual SAFETY GENERAL SAFETY RULES UNDERSTAND YOUR MACHINE Read this manual and labels affixed to the machine to understand its limitations and potential hazards. Be thoroughly familiar with the controls and their proper operation. Know how to stop the machine and disengage the controls quickly. Make sure to read and understand all the instructions and safety precautions as outlined in the Engine Manufacturer’s manual packed separately with your unit.
ENGINE SAFETY This machine is equipped with an internal combustion engine. Do not use on or near any unimproved, forest covered, or brush covered land unless the exhaust system is equipped with a spark arrester meeting applicable local, state, or federal laws. In the state of California, a spark arrester is required by law. Other states have similar laws. A spark arrester, if used, must be maintained in effective working order by the operator. Never start or run the engine inside a closed area.
Gas Log Splitter » Operator’s Manual SPECIFIC SAFETY RULES PREPARATION OF THE LOG VERTICAL OPERATING POSITION Both ends of the log should be cut as square as possible to prevent the log from rotating out of the splitter during operation. Never split logs greater than the specified log capacity. Do not operate the log splitter on icy, wet, muddy, or slippery ground. Only operate your log splitter on level ground.
Check before towing to make sure the log splitter is correctly and securely attached to the towing vehicle and the safety chains are secured to the hitch or bumper of the vehicle with enough slack to allow turning. Always use a class I, 2" ball with this log splitter. Use extra care when towing the log splitter. Do not exceed 45 mph. Towing the log splitter at a speed greater than 45 mph could result in loss of control, damage to the equipment, serious injury, or death.
Gas Log Splitter » Operator’s Manual Figure 1b CONTENTS SUPPLIED Your YARDMAX log splitter comes partially assembled and contains the following: 2 8 3 9 4 10 1 11 5 12 OPTIONAL 16 6 13 7 14 Handware Kit Premium 4-Cycle NET CONTENTS 35 OZ (1.05 L) 1. Beam and Reservoir with Engine 4. Wheel Axle 2. Fender (Left) 5. Wheels 3. Fender (Right) 6.
7. Tow Bar 8. Log Stripper M22 X1 4 X 50 X1 9. Log Cradle (Left) 4 X1 10. Log Cradle (Right) M12 X 30 X4 12. Muffler (YS2565 and YS2865 only) M22 X1 13. Operator’s Manual and Engine Manual 4 X 50 X1 11. Beam Lock Bracket 5 6 X1 14. T ools for Spark Plug Assembly (YS2565 and YS2865 only) 15. Engine Oil M10 X 25 X2 7 16. Log Table (Optional) X1 17.
Gas Log Splitter » Operator’s Manual SPLIT CONTROL LEVER U-Shaped Bracket 1. H olding the hydraulic cylinder handle, pull out the cylinder slowly and in a straight line until the output shaft in the cylinder is against the trunnion mount and locked in the U-shaped groove. 2. T he control handle is shipped hanging from the valve on the handle link. Remove the pin and cotter pin from the control handle. Move the control lever to the vertical Neutral positon (shown in circle on illustration Figure 3.
LOG STRIPPER (YS2565, YS2865, and YS3065 ONLY) TOW BAR 1. A lign holes in the log stripper with the holes in the trunnion mount. Insert the tow bar into the tank bracket and align the holes. Connect and tighten the tow bar to the tank by using the M12x80 bolts, flat washers, spring washers, and nuts. (See Figure 6) 2. I nstall the log stripper by tightening the M10x35 bolts, spring 19 mm and flat washers.
19 mm Gas Log Splitter » Operator’s Manual 18 mm 3. S lide the anti-dust washer and one roller bearing onto the axle. Use a soft-faced hammer to tap the roller bearing lightly to make sure the bearing is in the right position. 11. Remove the two M8x45 bolts, flat washers, and nuts. 16 mm X2 4. S lide the wheel with the valve stem facing out to the wheel axle and the other roller bearing, then put the wheel washer against the bearing. Use a 32mm socket to tighten the axle nut completely.
14. Move the bridge pin and lock pin from the upper hole to the lower hole. Make sure the bridge pin is connected to the wire rope first and then insert the lock pin. (See Figure 7g) 1 16. Rotate the bottom pallet slowly until there is enough space to assemble the other wheel. 2 Upper Hole Lock Pin Lower Hole Bridge Pin 3 4 16" Bottom Pallet Figure 7g Figure 7i 15. Put the axle with one wheel below the upper bracket. Make sure the wheel is on the engine side.
Gas Log Splitter » Operator’s Manual 19 mm 18. Follow the same procedure to assemble the other wheel. (Follow 16 mm steps 3 – 10 under wheel assembly.) 32 mm SUPPORT LEG 1. A lign the support leg to the upper hole on the unit. Insert the U-shaped lock pin to hold the support leg in place. 2. S lightly lift the machine by the tow bar while rotating it so that the support leg can drop to the down position supporting the machine on the ground Cotter Pin (x1) 3.
19 mm 19 mm 18 mm FENDER 16 mm MUFFLER (YS2565 / YS2865 ONLY) Align the left fender to the tank assembly. Insert the M8x20 bolts, spring washers, flat washers, and tighten by using a 13mm wrench. (See Figure 10) 1. R emove the plastic sheet by loosening and removing the nuts and washers, using a 13mm wrench. 16 mm Follow 32the mm same procedure to assemble the right fender. Plastic Sheet 13 mm 19 mm 13 mm M8x20 (x8) 18 mm Figure 12a 2.
Lower Hole Gas Log Splitter » Operator’s Manual LOG TABLE (OPTIONAL) Refer to Figures 15a and 15b to install the work table. Remove the bolts, flat washers, and nuts from the inside holes. Move the log cradle from the incline position to the horizontal position. Align holes on the log cradle with the outside holes on the beam mount. Reinstall bolts, flat washers, and nuts.
KNOW YOUR MACHINE FEATURES AND CONTROLS Log Table (Optional) Log Spinner Foot Plate 2-Position Log Cradle Split Control Handle Log Stripper Cylinder Hydraulic Cylinder Handle Manual Tube Beam Assembly Hydraulic Tank Horizontal Beam Lock Hydraulic Pump Hydraulic Breather/Dipstick Support Leg 2” Ball Hitch Coupler Safety Chains Vertical Beam Lock Control Valve 19 | Know Your Machine YS2565PM02 - 1703
Gas Log Splitter » Operator’s Manual Engine On/Off Switch Recoil Starter Handle Throttle Control Choke Control Fuel Shut-Off Valve LOG SPINNER FOOT PLATE The foot plate holds the log in place while the wedge splits the log. The foot plate allows the operator to easily spin a log in prep for splitting and allows the log to rotate when splitting instead of causing unnecessary stress on the beam. It is easy to replace when the grip teeth are damaged. No repair welding is required.
CHOKE CONTROL RECOIL STARTER HANDLE The choke control is used to choke the carburetor and assist in starting the engine. The choke control slides The handle is used to start the engine. between the CHOKE CLOSED positions. FUEL SHUT-OFF VALVE The fuel shut – off has two position. CLOSED ( ) - use this position to service, transport, or store the unit.
Gas Log Splitter » Operator’s Manual STARTING ENGINE STOP ENGINE 1. Make sure the control lever is in the neutral position. Return the cylinder to fully retracted position or home position. Move the Throttle lever to SLOW ( ). Move the engine switch to OFF. Close the fuel shut-off valve ( ). 2. M ove the engine switch to the ON position. OFF ON Sudden stopping at a high speed under a heavy load is not recommended. Engine damage may result. CLOSED OPEN 3. Open the fuel shut-off valve.
CONVERSION BETWEEN HORIZONTAL SPLITTING POSITION AND VERTICAL SPLITTING POSITION Neutral Position Reverse Position Forward Position Horizontal Beam Lock Horizontal Position Figure 16a Reverse Position Lifting Handle Neutral Position Forward Position Rotating Position Figure 16b Vertical Beam Lock STUCK LOG PROCEDURE If a log does not split completely and becomes stuck on the wedge, never attempt to remove it by modifying the splitter or adding attachments to the splitter.
Gas Log Splitter » Operator’s Manual TRANSPORTING MOVING BY HANDS 3. Make sure hitch is in good working order. The log splitter is heavy. It can crush and cause serious injury if it rolls out of control or tips over. 4. C heck safety chains. Two safety chains must be used while towing. Cross safety chains under the coupler, allowing only enough slack for vehicle turns. Follow the instructions below for safely moving the log splitter. 5. P ull the U-shaped lock pin away from the machine.
MAINTENANCE Inspect and maintain the log splitter before each use. If the log splitter has been used previously, it must be inspected and maintained before each subsequent use. Always shut off the engine and relieve system pressure before inspecting, cleaning, adjusting, or repairing the splitter. Relieve system pressure by moving the split control lever back and forth several times. Remove debris from the engine, muffler, and moving parts. Debris on a hot engine can be a fire hazard.
Gas Log Splitter » Operator’s Manual STORAGE Follow the instructions below for storing your log splitter between uses. 1. R etract the wedge completely to keep the rod protected from corrosion. 2. A llow the machine to cool 5 minutes before storing. 3. C lear the debris from the beam, wedge, and end plate. Use a damp cloth to clear exterior surfaces of the engine and log splitter. Use a soft bristle brush to remove excess dirt and oil. Use an air compressor (25 PSI) to clear dirt and small debris.
TROUBLESHOOTING Problem Wedge movement is slow or erratic Cause Remedy 2. Debris lodged in beam guides 1. P urge air by extending and retracting the wedge several times until motion is smooth 3. Low hydraulic oil 2. Clear debris from beam 1. Air in the hydraulic oil system 3. Check oil level and add as needed 1. Faulty cylinder rod seal 2. Scored or bent cylinder rod Oil leak from cylinder 3. Loose hydraulic fitting 4.
Gas Log Splitter » Operator’s Manual PARTS DIAGRAM YS2565/YS2865 * Parts List on page 34 YS2565PM02 - 1703 Parts Diagram | 28
YS2565/YS2865 PARTS LIST No. Description Qty No. Description Qty No.
Gas Log Splitter » Operator’s Manual YS3065 * Parts List on page 34 YS2565PM02 - 1703 Parts Diagram | 30
YS3065 PARTS LIST No. Description Qty No. Description Qty No.
Gas Log Splitter » Operator’s Manual YS3567 * Parts List on page 34 YS2565PM02 - 1703 Parts Diagram | 32
YS3567 PARTS LIST No. Description Qty No. Description Qty No.
Gas Log Splitter » Operator’s Manual OPTIONAL LOG TABLE No.
yardmax.com Tame the Great Outdoors 847-327-0566 or 844-YARDMAX | ® info@yardmax.