Shaded sitting nook Installation and Operating Instructions – YM11542 Revised 02/13/2013 Yardistry – North America Toll Free Customer Support: 1.888.509.4382 info@yardistrystructures.com www.yardistrystructures.com Yardistry / Selwood Products – Europe Customer Support: +44 1284 852569 parts@selwoodproducts.com www.selwoodproducts.com 1 support@yardistrystructures.
Important Safety Notice! Yardistry components are intended for privacy, decorative and ornamental use only. Product is NOT INTENDED for the following: • A safety barrier to prevent unsupervised access to pools, hot tubs, spas or ponds. • As load bearing support for a building, structure, heavy objects or swings. • Used in structures that trap wind, rain or snow that would create extra load on the product. Permanent structures may require a building permit.
Limited Warranty Yardistry warrants that this product is free from defect in materials and workmanship for a period of one year from the original date of purchase. In addition, all lumber is warranted for 5 years against rot and decay. This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance is required to assure the integrity of your product and is a requirement of the warranty. This warranty does not cover any inspection cost.
are approximate and are shown to assist in the identification of parts for Part Identification ( Dimensions ) assembly. Actual dimensions may be smaller or larger. 4pc. (220) - Beam End Short 25.4 x 101.6 x 203.2mm 2pc. (218) - Beam 25.4 x 101.6 x 492.1mm 4pc. (228) - Insert - Sitting Nook Post 38.1 x 38.1 x 127mm 4pc. (221) - X Horizontal A 38.1 x 63.5 x 419.1mm 4pc. (223) - X Diagonal 38.1 x 38.1 x 588.2mm 4pc. (213) - Support 38.1 x 76.2 x 492.1mm 4pc. (226) - Seat Back Brace 38.1 x 82.6 x 476.
are approximate and are shown to assist in the identification of parts for Part Identification ( Dimensions ) assembly. Actual dimensions may be smaller or larger. 2pc. (227) - X Panel Post Back 44.5 x 57.2 x 1930.4mm 2pc. (217) - X Panel Post Front 44.5 x 57.2 x 1930.4mm 2pc. (219) - Engineered Arch Beam 25.4 x 186.3 x 1930.4mm 1pc. (012) - Sitting Nook Sunshade Set Y70821-012 1pc. (216) - Window Triple Panel 38.1 x 495.3 x 1409.7mm Part Identification (Actual Size) 1pc.
Inventory Parts - Read This Before Starting Assembly STOP A. STOP STOP STOP his is the time for you to inventory all your hardware, wood and accessories, T referencing the parts identification sheets. This will assist you with your assembly. • Each step indicates which bolts and/or screws you will need for assembly, as well as any flat washers, lock washers, t-nuts or lock nuts. B.
Step 1: Attach Short Supports A: Lay one (217) X Panel Post Front and one (227) X Panel Post Back on edge, so the grooved sides face each other (fig 1.1). Notice the hole location on both posts.
Step 2: Attach Inserts Part 1 A: Loosely attach one (228) Insert inside the grooves of each (217) X Panel Post Front and (227) X Panel Post Back with 1 (YB4) 1/4 x 3 3/4” Wafer Bolt (with 5/16” flat washer) as shown in figures 2.1 & 2.2. Note the angled edge of (228) Insert is towards the bottom (fig. 2.2) Fig. 2.1 Fig. 2.2 228 217 227 Notice 5/16” flat YB4 orientation washer 4x Wood Parts 228 Insert 38.1 x 38.
Step 2: Attach Inserts Part 2 B: With an adult helper stand up posts and place one (211) Seat Back on the outside of both (227) X Panel Post Back and tight to the top of (215) Short Wide Supports (fig 2.3 & 2.4). Notice the hole is toward the bottom of the board. Insert one 1/4” Connector Nut into (211) Seat Back and loosely attach to previously installed (YB4) 1/4 x 3 3/4” Wafer Bolt on each side (fig 2.4).
Step 3: Insert X Panels Part 1 A: With an adult helper slide one (221) X Horizontal A down the grooves of each (217) X Panel Post Front and (227) X Panel Post Back so it sits tight to the top of (228) Inserts using 2 (YS4) #8 x 3” Wood Screws per side (fig 3.1 & 3.2). Fig. 3.1 Fig. 3.2 227 221 217 YS4 Tight x 2 per side 228 Wood Parts 2x 221 Hardware 8x X Horizontal A 38.1 x 63.5 x 419.1 mm 10 YS4 #8 x 3” Wood Screw support@yardistrystructures.
Step 3: Insert X Panels Part 2 B: Place one X Insert Pin into one (223) X Diagonal, then attach a second (223) X Diagonal to form a complete X Panel. Make sure the pieces are tight to each other (fig 3.3 & 3.4) Repeat for second assembly. Fig. 3.3 223 X Insert Pin Side View Fig. 3.4 223 Wood Parts 4x 223 Hardware X Diagonal 38.1 x 38.1 x 588.2 mm 2 x X Insert Pin 11 support@yardistrystructures.
Step 3: Insert X Panels Part 3 C: Slide one completed X Panel down the grooves of each (217) X Panel Post Front and (227) X Panel Post Back so it sits tight to the top of (221) X Horizontal Insert A as shown in fig. 3.5. Fig. 3.5 D: Slide one (221) X Horizontal A down to sit tight to the top of each completed X Panel (fig. 3.5 & 3.6) and attach with 2 (YS4) #8 x 3” Wood Screws per side (fig. 3.6) Fig. 3.
Step 4: Attach Arch Scrolls Fig. 4.1 Note orientation of Arch Scrolls (fig. 4.1, 4.2 & 4.3). A: Insert one (222) Arch Scroll between (217) X Panel Post Front and (227) X Panel Post Back so flat edge is tight to the top of (221) X Horizontal A (fig. 4.2 & 4.3) with 2 (S4) #8 x 3” Wood Screws as shown in fig 4.3. Repeat on other side of assembly. Fig. 4.3 227 222 Front YS4 217 x2 Fig. 4.2 Note: Flat edge sits tight to (221) X Horizontal A 221 Tight 2x Wood Parts 222 4 x Arch Scroll 38.1 x 130.
Step 5: Attach Beams to X Panel Posts A: Flush to the top and outside edges of (217) X Panel Post Front and (227) X Panel Post Back attach one (218) Beam per side with 4 (YS3) #8 x 2 1/2” Wood Screws per board (fig. 5.1 & 5.2). Fig. 5.1 Fig. 5.2 Fig. 3.6 227 217 227 217 YS3 Flush Flush 221 x 4 per board 218 YS4 Wood Parts 2x 218 Hardware 8x Beam 25.4 x 101.6 x 492.1 mm 14 YS3 #8 x 2 1/2” Wood Screw support@yardistrystructures.
Step 6: Attach Supports A: Attach one (213) Support tight to the inside of (217) X Panel Post Front and (227) X Panel Post Back on each side and flush to the tops of (211) Seat Back and (210) Seat Front using 4 (YS4) #8 x 3” Wood Screws per board (fig 6.1 & 6.2). Ensure the wide end of (213) Support is against (211) Seat Back (fig. 6.2) . B: Centre remaining (213) Supports over pilot holes in (211) Seat Back and (210) Seat Front as shown in fig. 6.1 and attach using 4 (YS4) #8 x 3 Wood Screws per board.
Step 7: Attach Seat Back Braces Part 1 A: Place two (226) Seat Back Braces on (213) Support so that the straight edges are flush to the back of each (227) X Panel Post Back and the bottom is tight to (211) Seat Back as shown in fig. 7.1 & 7.2. Note the orientation of (226) Seat Back Brace (fig 7.2). B: Attach each (226) Seat Back Brace to each (227) X Panel Post Back using 3 (YS4) #8 x 3” Wood Screws per board (fig. 7.1 & 7.2). Fig. 7.1 227 Fig. 7.
Step 7: Attach Seat Back Braces Part 2 C: Place one (226) Seat Back Brace on remaining (213) Supports as shown in fig 7.3 & 7.4. Attach (226) Seat Back Brace to (211) Seat Back using 1 Corner Brace with 3 (YS5) #8 x 1/2” Pan Screws per board (fig. 7.3 & 7.4). Fig. 7.3 Back View Fig. 7.4 226 226 213 Tight 213 YS5 x 3 per bracket 211 Corner Bracket 2x Wood Parts 226 6x Seat Back Brace 38.1 x 82.6 x 476.3 mm 2x 17 YS5 Hardware #8 x 1/2” Pan Screw Corner Brace support@yardistrystructures.
Step 8: Attach Seat Tops Part 1 A: Flush to the front edge of (210) Seat Front and outside edge of (213) Supports attach one (212) Seat Top with 8 (YS2) #8 x 1 1/2” Wood Screws per board (fig. 8.2). B: Attach one (212) Seat Top tight to the front of (226) Seat Back Braces and outside edges of (213) Supports using 8 (YS2) #8 x 1 1/2” Wood Screws per board (fig 8.1 & 8.2). Fig. 8.1 Fig. 8.
Step 8: Attach Seat Tops Part 2 C: Evenly space three (212) Seat Tops between previously installed (212) Seat Tops to (213) Supports and attach using 8 (S2) #8 x 1 1/2” Wood Screws per board (fig. 8.3). Fig. 8.3 212 x 8 per board YS2 213 213 (hidden) 3x Wood Parts 212 Hardware Seat Top 15.9 x 85.7 x 1409.7 24 x YS2 19 #8 x 1 1/2” Wood Screw support@yardistrystructures.
Step 8: Attach Seat Tops Part 3 D: Attach one (212) Seat Top flush to the top face of (212) Seat Top and one (212) Seat Top flush to the top of all four (226) Seat Back Braces using 8 (YS2) #8 x 1 1/2” Wood Screws per board (fig 8.4). E: Evenly space three (212) Seat Tops between previously installed (212) Seat Tops then attach to (226) Seat Back Braces using 8 (YS2) #8 x 1 1/2” Wood Screws per board (fig. 8.4). YS2 x 8 per board Flush Fig. 7.1 Flush 226 212 Tight 226 212 Fig. 7.
Step 9: Attach Window Triple Panel Part 1 A: With an adult helper place one (216) Window Triple Panel tight to the top of all (226) Seat Back Braces and tight to the inside edges of both (227) X Panel Post Back (fig 9.1). . B: Using two Sunburst Brackets and 6 (YS5) #8 x 1/2” Pan Screws attach (216) Window Triple Panel to the middle two (226) Seat Back Braces as shown in fig 9.1 & 9.2. Fig. 9.1 216 227 227 Fig. 9.
Step 9: Attach Window Triple Panel Part 2 C: Using 2 (YS4) #8 x 3” Wood Screws per side, attach (216) Window Triple Panel to each (227) X Panel Post Back as shown in fig. 9.3 & 9.4. Fig. 9.3 Fig. 9.4 216 227 Back View YS4 Hardware 4x 22 YS4 #8 x 3” Wood Screw support@yardistrystructures.
Step 10: Attach Panel Top Rail A: Tight to the inside edges of both (227) X Panel Post Back attach (225) Panel Top Rail to (216) Window Triple Panel using 4 (YS4) #8 x 3” Wood Screws (fig. 10.1 & 10.3). Ensure the groove in (225) Panel Top Rail sits over the top of (216) Window Triple Panel as shown in fig. 10.2. B: Ensure assembly is square and tighten all Wafer Bolts from Step 2. Fig. 10.2 Fig. 10.1 Fig. 9.1 225 Back View Side View Fig. 10.
Step 11: Arch Beam Assembly Part 1 A: Attach two (220) Beam End Short centered over the outside holes and flush to the top of (219) Engineered Arch Beam using 3 (YS3) #8 x 2 1/2” Wood Screws per side (fig. 11.1). Repeat for a second assembly. B: At the top of each (217) X Panel Post Front and (227) X Panel Post Back insert one 1/4” Wafer Connector Nut from inside the assembly as shown in fig. 11.2 & 11.3. Fig. 11.1 Flush 220 219 Fig. 11.2 YS3 x 3 per side 1/4” Wafer Connector Nut Fig. 11.
Step 11: Arch Beam Assembly Part 2 C: Attach one completed Arch Beam Assembly with (220) Beam End Shorts facing out, flush to the top of each (217) X Panel Post Front and (227) X Panel Post Back using 1 (YB1) 1/4 x 2” Wafer Bolt (with 5/16” flat washer and previously installed connector nut) per side (fig 11.4 & 11.5). Fig. 11.4 Fig. 11.
Step 12: Attach Trellis A: Center one (224) Trellis on the top of both Arch Beam Assemblies and attach using 2 (YS24) #10 x 4” Wood Screws (fig. 12.1). B: Place one (224) Trellis 1/4” from the start of the arch on each end of the Arch Beam Assemblies as shown in fig. 12.2 and attach using 2 (YS24) #10 x 4” Wood Screws per trellis (fig. 12.3 ) . C: Evenly space the remaining two (224) Trellis between the middle and outside pieces and attach with 2 (YS24) #10 x 4” Wood Screws per trellis as shown in fig. 12.
Step 13: Attach Sunshade A: Center Sunshade over (224) Trellis and attach two male snaps (fig. 13.2) into the center (224) Trellis and connect snaps (fig. 13.1). B: Pull Sunshade tight and mark and install male snaps on the two outside (224) Trellis then connect snaps (fig 13.1). C: Pull Sunshade tight and attach two male snaps to each (218) Beam and connect snaps (fig. 13.3) Fig. 13.1 Male Snap Fig. 13.2 Fig. 13.
NOTES 28 support@yardistrystructures.
NOTES 29 support@yardistrystructures.
NOTES 30 support@yardistrystructures.
NOTES 31 support@yardistrystructures.
YARDISTRY Consumer Registration Card First Name Initial Last Name Street Apt. No.
