日本語 マルチパーカッションラックビブラフォン English Multi-Frame Vibraphones Vibraphones multi-cadre Français YVRD2700 YVRD2700G 取扱説明書 Owner’s Manual Mode d’emploi 組み立ての前に、「 安全上のご注意」を必ずお読みください。 Be sure to read “PRECAUTIONS” before assembly. Assurez-vous de lire la section “PRÉCAUTIONS D’USAGE” avant le montage.
Multi-Frame Vibraphones YVRD2700 YVRD2700G English Owner’s Manual FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.
PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe and handy place for future reference. CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other property. These precautions include, but are not limited to, the following: Do not disassemble • Repairs or part replacement should not be attempted unless instructions are provided in the manual.
NOTICE INFORMATION To avoid the possibility of damage to the product, follow the notices below. n About this manual n Handling • Do not strike the tone bars with glockenspiel mallets or any other solid objects. Doing so may dent or scratch the tone bars, altering their pitch. • Do not use the instrument in locations with poor ventilation. • The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your instrument.
Confirmation of Packing Contents Before assembling the instrument, confirm that all parts are included as listed. * If any parts are missing, please contact the dealer where the instrument was purchased.
Assembly For safety, assembly should be performed by at least 2 persons in a location with sufficient space. 6 7 Rack pipe 6 7 Audience side Center rail 3 Player side Reinforcement stay 2 Leg section (bass side) 5 5 Pedal stay 4 Match “Y” 4 Match “Z” 1. Place the bass side leg section on a rug or other soft material spread on the floor with the hole for the pedal stay facing up.
Assembly Instrument 7. Attach the instrument to the rack. Side plate Position the instrument on the rack with the bolt holes (A) located on the side plate of the instrument aligned with the holes (B) on the rack side frame. Using the washers, spring washers, and knob head bolts supplied with the rack, attach the instrument to the rack from the underside of the rack (four locations). A Side frame Washer Take care not to pinch your fingers when placing the instrument onto the rack.
Assembly 10. Pedal Stroke Adjustment Loosen the center rod fixing bolts (refer to page 6) to adjust the protruding length of the center rod to the desired pedal stroke, and retighten the bolts. The recommended stroke (distance between pedal and floor) is 9/16" to 13/16" (1.5 to 2 cm). Pedal 9/16” – 13/16” (1.5 – 2 cm) Floor 11. Tone Bar Height Adjustment 11-1. Loosen the slide leg fixing bolts while supporting both the bass and treble side frames by hand. 11-2.
Assembly 13. Attach the supplied multi-frame clamp (RDC-10) to the rack pipe. 13-1 * Clamps can be attached as needed according to the accessories used. * The illustration shows one installation example. 13-1. Loosen the wingnut of the multi-frame clamp, and then remove the bolt from the slit. 13-2. Slide on the clamp at the position where the accessory will be installed. 13-2 13-3. Place the bolt back into the slit in the clamp with the washer on the outside of the clamp.
Specifications YVRD2700 YVRD2700G Range �������������������������������������� f–f3, 3 Octaves Standard Pitch ���������������������� A = 442 Hz Bars ����������������������������������������� Aluminum Alloy Bar sizes �������������������������������� 39–57 mm wide, 13 mm thick Tone Bar Finish �������������������� YVRD2700: Matte Anodized Silver Finish YVRD2700G: Anodized Gold Mirror Finish Dimensions (W x D x H) ����169 x 107 x 85–100 cm (66-1/2” x 42-1/8” x 33-1/2”–39-3/8”) Weight ���������������������������
About the dedicated vibraphone drive unit The YVRD2700 YVRD2700G dedicated vibraphone drive unit can be purchased as a service part through a Yamaha distributor. For details, please contact the store where you purchased the main unit.
PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe and handy place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Do not disassemble Power supply/AC adaptor • This product contains no user-serviceable parts.
CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the units or other property. These precautions include, but are not limited to, the following: Handling Transportation and Installation • Treating the controller or driver roughly may damage the internal circuit board, etc. • Keep small parts out of the reach of infants. Your children may accidentally swallow them.
Things Necessary n Vibraphone Drive Unit (YVM-200) l Controller (Player Side) POWER Switch Turns the power on and off. MOTOR SPEED Slider Controls the fan rotation speed. z LED Indicator Lights when the power is turned on and flashes while the fan is rotating. START/STOP Button l Controller (Right Side) Starts and stops fan rotation. DC 12-15V IN Jack n Connects the power adaptor plug.
Assembly 1. Attach the driver. 1-1. Loosen the two wing bolts located underneath the treble side of the instrument. 1-1 Bass side Bottom view Treble side 1-2. Fully insert the driver mount into the support fitting. Loosen the fixing bolts. Slide the fittings. Fitting Support fitting Fitting 1-2 Pulley Fixing bolts Side view Support fitting Driver Driver Insert mount until it stops Treble side 1-3. Slide the fittings moved in step 1-1 back in the direction of the treble side.
Assembly 3. Connect the driver with the controller. Driver Connect the MOTOR IN terminal of the driver with the MOTOR OUT terminal of the controller using the supplied 8P DIN cable*. To connect, align the arrow mark ( ) on the plug with the screw next to the jack. * In case the 8P DIN cable is misplaced, the following spare part may be ordered: Part No. Part Name W5172200 8P DIN Cable Screw Controller Arrow mark Screw Arrow mark 8P DIN cable Fan side 4. Attach the round belt (fan belt)*.
Power Supply Prepare the supplied AC adaptor. z Connect the small plug of the AC adaptor to the DC 12-15V IN jack on the controller. Controller AC adaptor AC DC 12-15V IN x Plug the AC adaptor into a power outlet. * Wrapping the AC adaptor cord once around one of the legs will prevent accidental disconnection of the adaptor plug.
VGP3220 版次 ：2023 R3 © 2023 Yamaha Corporation Published 05/2023 IPTO-A1
