Owner's Manual

ManualsBrandsYamaha ManualsOtherYSP-3000

120

121

122

123

124

125

126

127

128

129

Press ENTER to start the AUTO

SETUP procedure, and then

leave the room within 10 seconds.

The following screen appears on the TV. Leave the room

within 10 seconds before the AUTO SETUP procedure

starts.

The setup screen automatically changes during the AUTO

SETUP procedure.

When the AUTO SETUP procedure is completed, the

following screen appears on the TV.

If “ENVIRONMENT CHECK (FAILED) is displayed, see page

40 in the Owner’s Manual and then run the procedure again.

y Hint

• The result may differ depending on the environment.

• If any error occurs, the corresponding error message appears

on the screen. In this case, see “Error messages for AUTO

SETUP” on page 41 in the Owner’s Manual and then follow

the instructions. To start the AUTO SETUP procedure once

again, press RETURN.

Press ENTER.

The following screen appears on the TV for 2 seconds and

then the menu screen disappears from the TV.

Disconnect the IntelliBeam

microphone.

The AUTO SETUP has completed. Keep the IntelliBeam

microphone in a safe place.

The settings are automatically saved in the system memory.

Enjoy TV or DVD digital audio in surround sound.

For instructions on how to operate or set your TV or DVD player, refer to the owner’s manual supplied with each component.

Enjoying surround sound

Carry out the AUTO SETUP to adjust the settings that best match your

listening environment

The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud test tones to be output

during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress.

Press STANDBY/ON on the

remote control.

The power of this unit turns on.

Before operations, insert batteries into the remote control

(see page 30 in the Owner’s Manual).

If necessary, adjust the volume level of this unit.

If you have connected the subwoofer, set the volume and

crossover/high cut frequency. Refer to the hint on page

36 in the Owner’s Manual.

Check the digital signal being output at this unit.

The input channel indicators (see page 8 in the Owner’s Manual) are lit in the front panel display, and they switch

according to the channel composition of the corresponding input source. If the sound is output from your TV

speakers, mute the volume on your TV. For details about digital audio input signals, see page 46 in the Owner’s

Manual.

Press VOLUME +/

on the remote control to adjust the volume

level of this unit.

Press one of the beam mode buttons on the remote control

to select the desired beam mode.

Select one of the six beam modes that best matches the current input source of this unit.

For further information on the beam modes, see page 54 in the Owner’s Manual.

To fine-tune the listening environment parameters manually or make advanced settings for speaker positions,

sound beams, etc., see “MANUAL SETUP” on page 72 in the Owner’s Manual.

AUTO SETUP START

Will begin in 20sec

Please leave the room

**--------

[RETURN]:Cancel

Enjoying TV in surround sound

SHOW RESULT

MEASUREMENT COMPLETE

BEAM MODE :5BEAM

SUBWOOFER :NOT APPLICABLE

[ENTER]:Save set-up

[RETURN]:Do not save set-up

AUTO SETUP COMPLETE

Please remove the MIC from

the YSP and the listening

position.

TV/AV

YSP

ENTER

ENTRY

A-E

ENHANCER

DISPLAY RETURN

TV/AV

YSP

ENTER

ENTRY

A-E

ENHANCER

DISPLAY RETURN

Select the TV channel using the

remote control supplied with

your TV.

Set the operation mode selector

to YSP.

This unit switches to the YSP operation mode.

Press TV on the remote control

of this unit.

This unit switches to the TV playback mode.

More than 1.8 m (6.0 ft)

Within 1 m

(3.3 ft)

IntelliBeam

microphone

Cardboard

microphone

stand

Listening

position

Place the IntelliBeam microphone on

the extended center line of this unit

and 1.8 m (6.0 ft) or more away from

it. Also, make sure place the

IntelliBeam microphone within 1 m

(3.3 ft) upper or lower from the center

height of this unit.

IntelliBeam

microphone

Center line

Carry out the AUTO SETUP (IntelliBeam)

INTELLIBEAM MIC

1234

Set the IntelliBeam microphone at your normal listening position.

Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would

be when you are seated.

IntelliBeam microphone (supplied)

Connect the supplied IntelliBeam microphone to the INTELLIBEAM MIC

jack on the front panel.

You may want to use the supplied cardboard microphone stand for the AUTO SETUP. Assemble the stand and place the IntelliBeam

microphone on top of it as shown below.

MUTE TV INPUT TV MUTE

VOLUME CH TV VOL

Enjoying DVDs in surround sound

Select the DVD video input on

your TV.

Set the operation mode selector

to YSP.

This unit switches to the YSP operation mode.

1) Press DVD on the remote

control of this unit.

This unit switches to the DVD playback mode.

Play back the supplied demonstration

DVD on the DVD player.

Set the operation mode selector

to YSP.

This unit switches to the YSP operation mode.

Press and hold AUTO SETUP for

more than 2 seconds.

The menu screen appears on the TV.

If the menu screen does not appear, check the OSD video

pin cable (see the connection example on the front page).

Check the following points.

About the IntelliBeam microphone

• Is the microphone placed on an imaginary center line drawn

from this unit?

• Is the microphone placed within 1 m (3.3 ft) upper or lower

from the center height of this unit?

• Is the microphone placed more than 1.8 m (6.0 ft) from the

front of this unit?

About the room environment

• Is your listening room kept as quiet as possible?

Prepare to leave the room.

The best setting may not be done if you are in the room.

Prepare to leave the room in 10 seconds after pressing

ENTER in step 10.

y Hint

• When leaving the room, bring this guide with you.

• Wait outside the room during the AUTO SETUP procedure.

• The AUTO SETUP procedure takes about 3 minutes.

• To cancel the AUTO SETUP procedure after it is started,

press RETURN.

Turn on the power of your TV.

Select the appropriate video

input on your TV.

“YSP-3000” appears on your TV. If the OSD video pin cable

is connected to the video input 1 on the TV as shown in the

connection example, switch the video input to “1”.

Within 1 m

(3.3 ft)

TV/AV

YSP

ENTER

ENTRY

A-E

ENHANCER

DISPLAY RETURN

AUTO SETUP

PREPARATION & CHECK

Please connect the MIC.

Please place the MIC at least

1.8m/6ft away from the YSP

unit. The MIC should be set

at ear level when seated.

After [ENTER] is pressed,

please leave the room.

[ENTER]:Start [RETURN]:Cancel

Measurement takes about 3min.

231

VOL MODE

AUTO

SETUP

INPUTMODE

SLEEP

5BEAM 3BEAMST+3BEAM

A-E

PRESET/TUNE

SEARCH MEMORY

INTELLIBEAM MIC

TV/AV

YSP

ENTER

A-E

DISPLAY RETURN

TV/AV

YSP

ENTER

A-E

DISPLAY RETURN

AUX1 AUX2 AUX3

DVD

STB

INPUT1

PRESET/TUNE

SEARCH MEMORY

MACRO

231

VOL MODE

AUTO

SETUP

INPUTMODE

SLEEP

5BEAM 3BEAMST+3BEAM

STB

INPUT1

A-E

PRESET/TUNE

SEARCH MEMORY

MACRO

231

5BEAM

STEREO MY BEAM MY SUR.

3BEAMST+3BEAM

Cardboard

microphone stand

Upper bound

position of the

microphone

Lower bound position

of the microphone

AUX1 AUX2 AUX3

DVD

POWER POWERSTANDBY/ON

INPUT1 MACRO

VOLUME

MIN MAX

CROSSOVER/

HIGH CUT

MIN MAX

Subwoofer

Center height of

this unit

Continued from the front

Cardboard microphone stand (supplied)

Input channel indicators

0726_YSP-3000_En_guide.p65 7/26/07, 4:06 PM2