User Guide
Table Of Contents
- R1 OWNER'S MANUAL YZFR1W(C)
- INTRODUCTION
- IMPORTANT MANUAL INFORMATION
- TABLE OF CONTENTS
- SAFETY INFORMATION
- DESCRIPTION
- INSTRUMENT AND CONTROL FUNCTIONS
- Main switch/steering lock
- Indicator and warning lights
- Multi-function meter unit
- Handlebar switches
- Clutch lever
- Shift pedal
- Brake lever
- Brake pedal
- Fuel tank cap
- Fuel
- Catalytic converter
- Seats
- Helmet holders
- Adjusting the front fork
- Adjusting the shock absorber assembly
- Luggage strap holders
- EXUP system
- Sidestand
- Ignition circuit cut-off system
- PRE-OPERATION CHECKS
- PERIODIC MAINTENANCE AND MINOR REPAIR
- PERIODIC MAINTENANCE
- Owner's tool kit
- Periodic maintenance chart for the emission control system
- General maintenance and lubrication chart
- Removing and installing cowlings and panels
- Checking the spark plugs
- Canister (for California only)
- Engine oil and oil filter cartridge
- Coolant
- Replacing the air filter element
- Checking the throttle cable free play
- Valve clearance
- Tires
- Cast wheels
- Accessories and replacement parts
- Adjusting the clutch lever free play
- Adjusting the rear brake light switch
- Checking the front and rear brake pads
- Checking the brake fluid level
- Changing the brake fluid
- Drive chain slack
- Cleaning and lubricating the drive chain
- Checking and lubricating the cables
- Checking and lubricating the throttle grip and cable
- Checking and lubricating the brake and clutch levers
- Checking and lubricating the shift pedal
- Checking and lubricating the sidestand
- Lubricating the swingarm pivots
- Checking the front fork
- Checking the steering
- Checking the wheel bearings
- Battery
- Replacing the fuses
- Replacing a headlight bulb
- Tail/brake light
- Replacing a turn signal light bulb
- Replacing the license plate light bulb
- Replacing an auxiliary light bulb
- Supporting the motorcycle
- Front wheel
- Rear wheel
- Troubleshooting
- Troubleshooting charts
- MOTORCYCLE CARE AND STORAGE
- SPECIFICATIONS
- CONSUMER INFORMATION
- INDEX
PERIODIC MAINTENANCE AND MINOR REPAIR
6-15
6
N
O
TE:
Make sure that the O-ring is properly
seated.
7. Install the new oil filter cartridge
with an oil filter wrench, and then
tighten it to the specified torque
with a torque wrench.
8. Install the engine oil drain bolt, and
then tighten it to the specified
torque.
NOTE:
Check the washer for damage and re-
place it if necessary.
9. Add the specified amount of the
recommended engine oil, and then
install and tighten the oil filler cap.
CAUTION:
ECA11620
● In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
● Make sure that no foreign mate-
rial enters the crankcase.
10. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
1. O-ring 1. Torque wrench
Tightening torque:
Oil filter cartridge:
17 Nm (1.7 m·kgf, 12 ft·lbf)
Tightening torque:
Engine oil drain bolt:
43 Nm (4.3 m·kgf, 31 ft·lbf)
Recommended engine oil:
See page 8-1.
Oil quantity:
Without oil filter cartridge replace-
ment:
2.90 L (3.07 US qt) (2.55 Imp.qt)
With oil filter cartridge replacement:
3.10 L (3.28 US qt) (2.73 Imp.qt)
U4C810E0.book Page 15 Wednesday, September 27, 2006 3:06 PM