Operation Manual
Table Of Contents
- INTRODUCTION
- IMPORTANT MANUAL INFORMATION
- TABLE OF CONTENTS
- SAFETY INFORMATION
- DESCRIPTION
- INSTRUMENT AND CONTROL FUNCTIONS
- Immobilizer system
- Main switch/steering lock
- Indicator lights and warning lights
- Multi-function meter unit
- Handlebar switches
- Clutch lever
- Shift pedal
- Brake lever
- Brake pedal
- ABS (for ABS models)
- Fuel tank cap
- Fuel
- Fuel tank breather hose and overflow hose
- Catalytic converter
- Seat
- Helmet holder
- Storage compartment
- Handlebar position
- Adjusting the shock absorber assembly
- Sidestand
- Ignition circuit cut-off system
- FOR YOUR SAFETY – PRE-OPERATION CHECKS
- OPERATION AND IMPORTANT RIDING POINTS
- PERIODIC MAINTENANCE AND ADJUSTMENT
- Owner’s tool kit
- Periodic maintenance chart for the emission control system
- General maintenance and lubrication chart
- Removing and installing the cowling and panels
- Checking the spark plugs
- Engine oil and oil filter cartridge
- Coolant
- Replacing the air filter element
- Adjusting the engine idling speed
- Checking the throttle grip free play
- Valve clearance
- Tires
- Cast wheels
- Adjusting the clutch lever free play
- Checking the brake lever free play
- Brake light switches (for ABS models)
- Brake light switches (for non-ABS models)
- Checking the front and rear brake pads
- Checking the brake fluid level
- Changing the brake fluid
- Drive chain slack
- Cleaning and lubricating the drive chain
- Checking and lubricating the cables
- Checking and lubricating the throttle grip and cable
- Checking and lubricating the brake and shift pedals
- Checking and lubricating the brake and clutch levers
- Checking and lubricating the sidestand
- Lubricating the swingarm pivots
- Checking the front fork
- Checking the steering
- Checking the wheel bearings
- Battery
- Replacing the fuses
- Replacing the headlight bulb
- Replacing the tail/brake light bulb
- Replacing a turn signal light bulb
- Replacing the license plate light bulb
- Replacing the auxiliary light bulb
- Supporting the motorcycle
- Front wheel (for non-ABS models)
- Rear wheel (for non-ABS models)
- Troubleshooting
- Troubleshooting charts
- MOTORCYCLE CARE AND STORAGE
- SPECIFICATIONS
- CONSUMER INFORMATION
PERIODIC MAINTENANCE AND ADJUSTMENT
6-14
6
4. Add coolant to the maximum level
mark, and then install the coolant
reservoir cap. WARNING! Re-
move only the coolant reservoir
cap. Never attempt to remove
the radiator cap when the en-
gine is hot.
[EWA15161] NOTICE: If
coolant is not available, use dis-
tilled water or soft tap water in-
stead. Do not use hard water or
salt water since it is harmful to
the engine. If water has been
used instead of coolant, replace
it with coolant as soon as possi-
ble, otherwise the cooling sys-
tem will not be protected
against frost and corrosion. If
water has been added to the
coolant, have a Yamaha dealer
check the antifreeze content of
the coolant as soon as possible,
otherwise the effectiveness of
the coolant will be reduced.
[ECA10472]
5. Route the coolant reservoir breath-
er hose through the guide as
shown.
EAU46822
To change the coolant
1. Place the vehicle on a level sur-
face and let the engine cool if nec-
essary.
2. Remove cowling A and panel B.
(See page 6-8.)
3. Place a container under the engine
to collect the used coolant.
4. Remove the radiator cap retaining
bolt, radiator cap retainer and radi-
ator cap. WARNING! Never at-
tempt to remove the radiator
cap when the engine is hot.
[EWA10381]
1. Coolant reservoir cap
2. Coolant reservoir breather hose
3. Guide
3
1
2
Coolant reservoir capacity (up to
the maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
1. Coolant reservoir breather hose
2. Guide
2
1
1. Radiator cap
2. Radiator cap retaining bolt
3. Radiator cap retainer
2
1
3
U20SE3E0.book Page 14 Monday, April 23, 2012 10:47 AM