Quick Guide

26
TF series Quick Guide
General specifications
Sampling Frequency
*1
Internal clock: 48 kHz; Dante clock: 48 kHz, 44.1 kHz (when using NY64-D)
Signal Delays Less than 2.6 ms, INPUT to OMNI OUT, Fs=48 kHz
Fader 100 mm motorized, Resolution = 10-bit, +10 dB to –138 dB, –∞ dB all faders
Frequency Response +0.5, –1.5 dB 20 Hz–20 kHz, refer to +4 dBu output @1kHz, INPUT to OMNI OUT
Total Harmonic
Distortion
*2
Less than 0.05% 20 Hz–20 kHz @+4 dBu into 600 Ω, INPUT to OMNI OUT, Input Gain=Min.
Hum & Noise
*3
–128 dBu typ., Equivalent Input Noise, Input Gain=Max.,
–85 dBu, Residual output noise, ST master off
Dynamic Range
110 dB typ., DA Converter,
107 dB typ., INPUT to OMNI OUT, Input Gain=Min.
Crosstalk@1 kHz
*4
–100 dB, adjacent INPUT/OMNI OUT channels, Input Gain=Min.
Dimensions (W x H
x D)
Net Weight
TF5: 866 mm × 225 mm × 599 mm, 20.0 kg
TF3: 716 mm × 225 mm × 599 mm, 17.0 kg
TF1: 510 mm × 225 mm × 599 mm, 13.5 kg
Power Requirements
(wattage)
TF5: 120W, TF3: 110W, TF1: 100W
Power Requirements
(voltage and hertz)
100–240 V 50/60 Hz
Temperature Range
Operating temperature range: 0–40 °C
Storage temperature range: -20–60 °C
Included Accessories Quick Guide, Power Cord
*1. Pull-up/down function is not supported.
*2. Total Harmonic Distortion is measured with a –18 dB/octave filter@80 kHz.
*3. Hum & Noise are measured with an A-Weight filter.
*4. Crosstalk is measured with a –30 dB/octave fi lter@22 kHz.
Input/output characteristics
Analog input specifications
Input jacks GAIN
Input
impedance
Source impedance
Input levels
Connectors
Sensitivity
*1
Standard level Max. non-clipping level
INPUT1-32 (TF5)
INPUT1-24 (TF3)
INPUT1-16 (TF1,TF-RACK)
+66 dB
7.5 kΩ
50 - 600 Ω Mics or
600 Ω Lines
-82 dBu (61.6 μV) -62 dBu (0.616 mV) -42 dBu (6.16 mV)
Combo Jack (XLR-3-31 type
*2
or
TRS phone
*3
) (Balanced)
-6 dB -10 dBu (245 mV) +10 dBu (2.45 V) +30 dBu (24.5 V)
ST IN 1,2 — 10 kΩ 600 Ω Lines -30 dBV (31.6 μV) -10 dBV (316 mV) +10 dBV (3.16 V) RCA Pin Jack (Unbalanced)
*1. “Sensitivity” is the necessary input level for outputting at +4 dBu (1.23 V) or at standard levels, when all faders and level controls are set to maximum.
*2. The XLR-3-31 connector is a balanced-type connector (1=GND, 2=HOT, 3=COLD).
*3. The TRS phone connector is a balanced-type connector (Tip=HOT, Ring=COLD, Sleeve=GND).
*4. This is 0 dBu=0.775 Vms for all specifications.
*5. The input jacks use +48V DC (phantom power), which can be set on/off for each jack in the software of this unit.
10. Specifications