User Manual

Предисловие
Введение в SP2060
Регуляторы и подключения
Работа с панелью
Настройки сети
Справочники
SP2060 Руководство пользователя 29
Работа с панелью
5. Для подтверждения сделанного выбора
нажмите на клавишу [YES].
Будет вызвана нужная библиотека, а устройство вер-
нется к дисплею Library List.
Panel Operation
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction to the SP2060
The Controls and Connectors
30
5. To confirm the selection, press the [YES] key.
The library is recalled and the unit returns to the Library
List display.
To cancel the recall operation, press the [NO] key, in-
stead of the [YES] key. The unit returns to the Library
List display.
LIMITER
You can set up the Output channel limiter.
The Limiter precludes signal levels higher than a specified
threshold to avoid speaker damage from excess output level.
1. Press the [LIMITER] key to select the Limiter
display.
2. Press the [SEL] key for the target channel.
The [SEL] key LED of the selected channel lights up,
and the corresponding channel name is displayed.
3. Press the [LIMITER], [BACK] or [NEXT] key to
display the On/Off parameter.
4. Press the [▲INC] key to set the On/Off
parameter to On to apply the Limiter to the
signal. Press the [▼DEC] key to set the On/
Off parameter to Off to cancel the Limiter.
5. Press the [NEXT]/[BACK] keys to select a
parameter to edit.
6. Press the [▲INC]/[▼DEC] keys to set the
parameter value.
SCENE
About a scene
The SP2060 enables you to store various parameter settings
as part of scene, and recall them via the front panel or re-
motely from DME Designer.
You can store the following settings in a scene:
• Configuration
• Routing
• Parameter sets of all components
• Scene titles
• Scene protection status
• INPUT A/B LINK
• The title of the library most recently recalled
HINT
You can use the library data for speaker processor components for
DME64N/24N that you have created using DME Designer.
Parameter Range Function
THRESHOLD –54 through 0dB
Sets the threshold
value.
ATTACK
FAST
MID
SLOW
MANUAL (0–
120.0ms)
Sets the attack time.
RELEASE
FAST
MID
SLOW
MANUAL
44.1kHz: 6ms–46s,
48kHz: 5ms–42.3s,
88.2kHz: 3ms–23s,
96kHz: 3ms–21.1s
Sets the release time.
If you select Fast,
Mid, or Slow, the unit
automatically sets the
optimum value based
on the maximum
wave length of audio
input to the Limiter.
NOTE
• You can set the attack time only when “Manual” is selected for
the Attack parameter.
• You can set the release time only when “Manual” is selected for
the Release parameter.
LIBRARY LIST
IF2112/95
HINT
You can protect a scene to forbid overwriting.
OUT 1
ON/OFF = ON
OUT 4
ON/OFF = ON
OUT 4
THRESHOLD= -54dB
Для отмены операции вызова, вместо клавиши [YES],
нажмите на клавишу [NO]. Устройство вернется к
дисплею Library List.
СОВЕТ:
Можно использовать данные библиотеки, созданные с ис-
пользованием программы DME Designer, для компонентов
процессора акустических систем для DME64N/24N.
ЛИМИТЕР
Настройка лимитера Выходного канала.
Лимитер предотвращает повышение уровня сигнала выше
определенного порога, во избежание повреждения акусти-
ческой системы из-за чрезмерно высокого уровня выходно-
го сигнала.
Параметр Диапазон Функция
THRESHOLD –54 до 0dB Установка значения
порога
ATTACK FAST
MID
SLOW
MANUAL (0– 120.0ms)
Установка времени
атаки
RELEASE FAST
MID
SLOW
MANUAL
44.1kHz: 6ms–46s,
48kHz: 5ms–42.3s,
88.2kHz: 3ms–23s,
96kHz: 3ms–21.1s
Установка вре-
мени отпускания.
При выборе опции
Fast, Mid, или Slow,
устройство автома-
тически устанавли-
вает оптимальное
значение исходя из
максимальной дли-
ны волны входного
аудио сигнала на
лимитере.
ПРИМЕЧАНИЕ:
• Установка времени атаки возможна только в том случае,
когда для параметра Attack (Атака) установлена опция
«Manual».
• Установка времени отпускания возможна только в том
случае, когда для параметра Release (Отпускание) уста-
новлена опция «Manual».
1. Нажмите на клавишу [LIMTER] для выбо-
ра экрана LIMITER (Лимитер).
Panel Operation
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction to the SP2060
The Controls and Connectors
30
5. To confirm the selection, press the [YES] key.
The library is recalled and the unit returns to the Library
List display.
To cancel the recall operation, press the [NO] key, in-
stead of the [YES] key. The unit returns to the Library
List display.
LIMITER
You can set up the Output channel limiter.
The Limiter precludes signal levels higher than a specified
threshold to avoid speaker damage from excess output level.
1. Press the [LIMITER] key to select the Limiter
display.
2. Press the [SEL] key for the target channel.
The [SEL] key LED of the selected channel lights up,
and the corresponding channel name is displayed.
3. Press the [LIMITER], [BACK] or [NEXT] key to
display the On/Off parameter.
4. Press the [▲INC] key to set the On/Off
parameter to On to apply the Limiter to the
signal. Press the [▼DEC] key to set the On/
Off parameter to Off to cancel the Limiter.
5. Press the [NEXT]/[BACK] keys to select a
parameter to edit.
6. Press the [▲INC]/[▼DEC] keys to set the
parameter value.
SCENE
About a scene
The SP2060 enables you to store various parameter settings
as part of scene, and recall them via the front panel or re-
motely from DME Designer.
You can store the following settings in a scene:
• Configuration
• Routing
• Parameter sets of all components
• Scene titles
• Scene protection status
• INPUT A/B LINK
• The title of the library most recently recalled
HINT
You can use the library data for speaker processor components for
DME64N/24N that you have created using DME Designer.
Parameter Range Function
THRESHOLD –54 through 0dB
Sets the threshold
value.
ATTACK
FAST
MID
SLOW
MANUAL (0–
120.0ms)
Sets the attack time.
RELEASE
FAST
MID
SLOW
MANUAL
44.1kHz: 6ms–46s,
48kHz: 5ms–42.3s,
88.2kHz: 3ms–23s,
96kHz: 3ms–21.1s
Sets the release time.
If you select Fast,
Mid, or Slow, the unit
automatically sets the
optimum value based
on the maximum
wave length of audio
input to the Limiter.
NOTE
• You can set the attack time only when “Manual” is selected for
the Attack parameter.
• You can set the release time only when “Manual” is selected for
the Release parameter.
LIBRARY LIST
IF2112/95
HINT
You can protect a scene to forbid overwriting.
OUT 1
ON/OFF = ON
OUT 4
ON/OFF = ON
OUT 4
THRESHOLD= -54dB
2. Нажмите на клавишу [SEL] для выбора
нужного канала.
Клавиша [SEL] выбранного канала загорится, и на
экране будет выведено имя соответствующего канала.
Panel Operation
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction to the SP2060
The Controls and Connectors
30
5. To confirm the selection, press the [YES] key.
The library is recalled and the unit returns to the Library
List display.
To cancel the recall operation, press the [NO] key, in-
stead of the [YES] key. The unit returns to the Library
List display.
LIMITER
You can set up the Output channel limiter.
The Limiter precludes signal levels higher than a specified
threshold to avoid speaker damage from excess output level.
1. Press the [LIMITER] key to select the Limiter
display.
2. Press the [SEL] key for the target channel.
The [SEL] key LED of the selected channel lights up,
and the corresponding channel name is displayed.
3. Press the [LIMITER], [BACK] or [NEXT] key to
display the On/Off parameter.
4. Press the [▲INC] key to set the On/Off
parameter to On to apply the Limiter to the
signal. Press the [▼DEC] key to set the On/
Off parameter to Off to cancel the Limiter.
5. Press the [NEXT]/[BACK] keys to select a
parameter to edit.
6. Press the [▲INC]/[▼DEC] keys to set the
parameter value.
SCENE
About a scene
The SP2060 enables you to store various parameter settings
as part of scene, and recall them via the front panel or re-
motely from DME Designer.
You can store the following settings in a scene:
• Configuration
• Routing
• Parameter sets of all components
• Scene titles
• Scene protection status
• INPUT A/B LINK
• The title of the library most recently recalled
HINT
You can use the library data for speaker processor components for
DME64N/24N that you have created using DME Designer.
Parameter Range Function
THRESHOLD –54 through 0dB
Sets the threshold
value.
ATTACK
FAST
MID
SLOW
MANUAL (0–
120.0ms)
Sets the attack time.
RELEASE
FAST
MID
SLOW
MANUAL
44.1kHz: 6ms–46s,
48kHz: 5ms–42.3s,
88.2kHz: 3ms–23s,
96kHz: 3ms–21.1s
Sets the release time.
If you select Fast,
Mid, or Slow, the unit
automatically sets the
optimum value based
on the maximum
wave length of audio
input to the Limiter.
NOTE
• You can set the attack time only when “Manual” is selected for
the Attack parameter.
• You can set the release time only when “Manual” is selected for
the Release parameter.
LIBRARY LIST
IF2112/95
HINT
You can protect a scene to forbid overwriting.
OUT 1
ON/OFF = ON
OUT 4
ON/OFF = ON
OUT 4
THRESHOLD= -54dB
3. Нажмите на клавишу [LIMITER], [BACK]
или [NEXT] для просмотра параметра
On/Off.
4. Нажмите на клавишу [
/
INC] для вклю-
чения лимитера в сигнале. Нажмите на
клавишу [
\
DEC] для выключения лими-
тера в сигнале.
5. Для выбора редактируемого параметра
нажмите на клавиши [NEXT]/[BACK].
Panel Operation
SP2060 Owner’s Manual
Foreword
Network Settings ReferencesPanel Operation
Introduction to the SP2060
The Controls and Connectors
30
5. To confirm the selection, press the [YES] key.
The library is recalled and the unit returns to the Library
List display.
To cancel the recall operation, press the [NO] key, in-
stead of the [YES] key. The unit returns to the Library
List display.
LIMITER
You can set up the Output channel limiter.
The Limiter precludes signal levels higher than a specified
threshold to avoid speaker damage from excess output level.
1. Press the [LIMITER] key to select the Limiter
display.
2. Press the [SEL] key for the target channel.
The [SEL] key LED of the selected channel lights up,
and the corresponding channel name is displayed.
3. Press the [LIMITER], [BACK] or [NEXT] key to
display the On/Off parameter.
4. Press the [▲INC] key to set the On/Off
parameter to On to apply the Limiter to the
signal. Press the [▼DEC] key to set the On/
Off parameter to Off to cancel the Limiter.
5. Press the [NEXT]/[BACK] keys to select a
parameter to edit.
6. Press the [▲INC]/[▼DEC] keys to set the
parameter value.
SCENE
About a scene
The SP2060 enables you to store various parameter settings
as part of scene, and recall them via the front panel or re-
motely from DME Designer.
You can store the following settings in a scene:
• Configuration
• Routing
• Parameter sets of all components
• Scene titles
• Scene protection status
• INPUT A/B LINK
• The title of the library most recently recalled
HINT
You can use the library data for speaker processor components for
DME64N/24N that you have created using DME Designer.
Parameter Range Function
THRESHOLD –54 through 0dB
Sets the threshold
value.
ATTACK
FAST
MID
SLOW
MANUAL (0–
120.0ms)
Sets the attack time.
RELEASE
FAST
MID
SLOW
MANUAL
44.1kHz: 6ms–46s,
48kHz: 5ms–42.3s,
88.2kHz: 3ms–23s,
96kHz: 3ms–21.1s
Sets the release time.
If you select Fast,
Mid, or Slow, the unit
automatically sets the
optimum value based
on the maximum
wave length of audio
input to the Limiter.
NOTE
• You can set the attack time only when “Manual” is selected for
the Attack parameter.
• You can set the release time only when “Manual” is selected for
the Release parameter.
LIBRARY LIST
IF2112/95
HINT
You can protect a scene to forbid overwriting.
OUT 1
ON/OFF = ON
OUT 4
ON/OFF = ON
OUT 4
THRESHOLD= -54dB
6. Для установки значения параметра, на-
жмите на клавиши [
/
INC]/[
\
DEC]
СЦЕНА
О сцене
SP2060 позволяет сохранить различные настройки парамет-
ра как часть сцены для последующего вызова с передней
панели или с использованием программы DME Designer. В
сцене могут быть сохранены следующие настройки:
• Конфигурация
• Маршрутизация
• Настройки параметров всех компонентов
• Имена сцены
• Статус защиты сцены
• INPUT A/B LINK
• Имя наиболее часто вызываемой библиотеки
СОВЕТ:
Возможная установка защиты сцены от случайного стира-
ния или перезаписи.