User Manual

ManualsBrandsYamaha ManualsElectronic KeyboardS90 XS

Reference Manual

Reference

Voice

Performance

Multi

SEQ Play

Master

Remote

File

Audio Rec/Play

Utility

Voice

Play

Normal Voice Edit

Common Edit

Name

Play Mode

Arpeggio

Arp Edit

Arp 1-5 Type

Controller

LFO

Filter/EG

3 Band EQ

Effect

Element Edit

OSC

Tune

PEG

Filter Type

FEG

Filter Scale

AMP Level/Pan

AEG

AMP Scale

LFO

Drum Voice Edit

Common Edit

Name

Play Mode

Arpeggio

Controller

Filter/EG

3 Band EQ

Effect

Key Edit

OSC

Tune

Filter Type

AMP Level/Pan

AEG

Job

Recall

Bulk

Supplementary Info.

Basic Structure

Appendix

Ctrl Set 1 – 6 Src (Controller Set 1 – 6 Source)

Determines which panel controller is to be assigned and used for the selected Set. You can also assign multiple

functions to a controller.

Settings: PitchBend (Pitch Bend Wheel), ModWheel (Modulation Wheel), AfterTch (After Touch), FootCtrl1 (Foot Controller 1), FootSw

(Foot Switch), Ribbon (Ribbon Controller), Breath (Breath Controller), Assign 1, Assign 2, FootCtrl2 (Foot Controller 2), A. Func 1

(Assignable Function 1), A. Func 2 (Assignable Function 2)

NOTE: The Control Number in Controller display in the Utility mode can be selected for the controller which can be changed in this

parameter.

NOTE: You can determine the degree to which the Pitch Bend wheel affects the Destination parameter (below) by setting the Pitch

Bend Range Upper and Pitch Bend Range Lower in the Play Mode display (page 35).

Ctrl Set 1 – 6 Dest (Controller Set 1 – 6 Destination)

Determines the parameter that is controlled by the Source controller (above). You can select a parameter for each

controller from the 101 parameters, such as volume, pitch and LFO depth.

Settings: Refer to the Control List in the Data List (separate PDF documentation).

NOTE: Regarding “Insertion Effect A Parameter 1 – 16,” “Insertion Effect B Parameter 1 – 16” and “Vocoder 1 – 32” described in the

Control List, the actual parameter names of the selected Effect type are shown on the display. If “insA/B---(Prm 1 – 16)” is shown

instead of a clear name, no function is assigned to that parameter.

NOTE: When at least one of the “Controller Set 1 – 6 Element Sw” parameters is set to “off” and the Element related parameters are

assigned to any of the “Ctrl Set 1 – 6 Dest” parameters, an exclamation mark (“!”) is shown at the beginning of the value for “Ctrl

Set 1 – 6 Src,” “Ctrl Set 1 – 6 Dest” and “Ctrl Set 1 – 6 Depth.” This indicates that the function specified as destination is not

applied to all the Elements.

Ctrl Set 1 – 6 Depth (Controller Set 1 – 6 Depth)

Determines the degree to which the Source controller affects the Destination parameter. For negative values, the

controller operation is reversed; maximum controller settings produce minimum parameter changes.

Settings: -64 – +0 – +63

Controller Set 1 – 6 Element Sw (Controller Set 1 – 6 Element Switch)

Determines whether or not the selected controller affects each individual Element. This parameter is disabled when the

“Ctrl Set 1 – 6 Dest” described above is set to a parameter unrelated to the Voice Elements. When some buttons are set

to “on,” the corresponding Elements are to be affected by the selected controller.

Determines how the vibrato, tremolo and wah effect are produced by using the LFO (Low Frequency Oscillator). From

the following displays, you can set the basic LFO parameters common to all Elements of the Voice.

Wave

Selects the Wave and determines how the LFO waveform modulates the sound.

Settings: triangle, triangle+, saw up, saw down, squ1/4 (Square 1/4), squ1/3 (Square 1/3), square, squ2/3 (Square 2/3), squ3/4 (Square 3/

4), trapezoid, S/H1 (Sample and Hold 1), S/H2 (Sample and Hold 2), user

Play Mode

Determines whether the LFO cycles repeatedly (loop) or only once (one shot).

Settings: loop, one shot

Speed

Determines the speed of the LFO Wave. The higher the value, the faster the speed. This parameter is disable when the

“Tempo Sync” is set to on.

Settings: 0 – 63

5 LFO (Common LFO)

user You can create your original LFO wave by selecting this. Creating LFO waves is available only on the S90 XS/S70 XS Editor. For

details, refer to “User LFO Template” section (page 43).