User Manual

Reference Manual
Basic Structure
23
Basic Structure
Functional Blocks
Tone Generator
A/D Input
Arpeggio
Sequencer
Audio Record/Play
Controller
Effect
Internal Memory
Reference
Voice
Performance
Multi
SEQ Play
Master
Remote
File
Audio Rec/Play
Utility
Appendix
About MIDI
Display Messages
Troubleshooting
*1: The Bottom parameter is available only when the value is less than that of the Top parameter.
*2: The Color parameter may not be effective depending on the values of the Mode and Stage parameters.
*3: The Top parameter is available only when the value is more than that of the Bottom parameter.
Pan AEG Type
This parameter of the Slice effect determines the type of the AEG applied to the panned sound.
Pan Depth
Determines the depth of the pan effect.
Pan Direction
Determines the direction toward which the stereo pan position of the sound moves.
Pan Type
Determines the pan type.
Pedal Control
When “VCM Pedal Wah” is selected, this parameter determines the cutoff frequency of the wah filter. For
best results, assign the this parameter to the Foot Controller in the Controller Set display, then use the
Foot Controller to control this parameter.
Pedal Response
Determines how the sound responds to the change of the damper control.
Phase Shift Offset
Determines the offset value of the phase modulation.
Pitch 1, 2
Determines the pitch in semitones for each of the 1st series and 2nd series.
PM Depth
Determines the depth of the pitch modulation.
Pre Mod HPF Cutoff
Frequency
Determines the Cutoff frequency of the High Pass Filter before the modulation.
Pre-LPF Cutoff Frequency
Determines the Cutoff frequency of the Low Pass Filter before the modulation.
Pre-LPF Resonance
Determines the Resonance of the Low Pass Filter for the input sound.
Presence
This parameter of the guitar amp effect controls high frequencies.
Ratio
Determines the ratio of the compressor.
Release
Determines the amount of time that elapses between the releasing of a key and the end of the
compressor effect.
Release Curve
Determines the release curve of the envelope follower.
Release Time
Determines the release time of the envelope follower.
Resonance
Determines the resonance of the filter.
Resonance Offset
Determines the resonance as offset.
Reverb Delay
Determines the delay time from the early reflections until the reverberations.
Reverb Time
Determines the reverb time.
Room Size
Determines the size of the room in which the instrument sounds.
Rotor Speed Fast
Determines the speed of the rotor when the slow/fast switch is set to “fast.”
Rotor Speed Slow
Determines the speed of the rotor when the slow/fast switch is set to “slow.”
Rotor/Horn Balance
Determines the volume balance of the horn and rotor.
Sampling Freq. Control
Controls the sampling frequency.
Sensitivity
When one of “Dynamic Flanger,” “Dynamic Phaser,” and the TEC effects is selected, this parameter
determines the sensitivity of the modulation applied to the input change.
When one of the VCM Touch Wah effects is selected, this parameter determines the sensitivity of the
wah filter's change applied to the input change.
Slow-Fast Time of Horn
Determines how long it takes for the rotation speed of the horn to change from the current speed (slow
or fast) to the other one (fast or slow) when the rotation speed is switched.
Slow-Fast Time of Rotor
Determines how long it takes for the rotation speed of the rotor to change from the current speed (slow
or fast) to the other one (fast or slow) when the rotation speed is switched.
Space Type
Selects the type of space simulation.
Speaker Type
Selects the type of speaker simulation.
Speed
When “VCM Flanger” is selected, this parameter determines the frequency of the LFO wave which
controls the cyclic change of the delay modulation.
When any of the phaser types is selected, this parameter determines the frequency of the LFO wave
which controls the cyclic change of the phase modulation.
When “VCM Auto Wah” is selected, this parameter determines the speed of the LFO.
Speed Control
Switches the rotary speed.
Spread
Determines the spread of the sound.
Stage
Determines the step number of the phase shifter.
Threshold
Determines the minimum input level at which the effect is applied.
To p
*3
Determines the maximum value of the wah filter.
Ty pe
When “VCM Flanger” is selected, this parameter determines the flanger type.
When any of the wah effects is selected, this parameter determines the type of the Auto Wah.
When “Early Reflection” is selected, this parameter determines the type of the reflection sound.
Vowel
Selects a vowel type.
Wall Vary
Determines the wall status of the simulated room. Higher settings produces more diffuse reflections.
Width
Determines the width of the simulated room.
Word Length
Determines the degree of sound roughness.
Parameter name Descriptions