User Manual

Reference Manual
Reference
75
Voice
Performance
Multi
SEQ Play
Master
Remote
File
Audio Rec/Play
Utility
Performance
Play
Mixing
Edit Select
Common Edit
Name
Play Mode
Arpeggio
Controller
Filter / EG
EQ
Effect
Parameter
A/D Out
A/D FX
Parameter
Part Edit
Voice
Play Mode
Arpeggio
Arp Edit
Arp 1-5 Type
Filter / EG
3 Band EQ
Rcv Sw
FX Send
Job Select
Recall
Bulk
Copy
Initialize
Supplementary Info.
Basic Structure
Appendix
Arp Tempo (Arpeggio Tempo)
Determines the tempo for the Arpeggio.
Settings: 5 – 300
NOTE: If you are using this instrument with an external sequencer, DAW software, or MIDI device, and you want to synchronize the
Arpeggio with that device, set the MIDI Sync parameter in the Utility MIDI display (page 137) to “external” or “auto.” When MIDI
Sync is set to “auto” (only when MIDI clock is received continuously) or “external,” the Tempo parameter here indicates
“external” and cannot be changed.
Sync Qntz Val (Sync Quantize Value)
Determines the actual timing at which the next Arpeggio playback starts when you trigger it while the Arpeggio of a
certain Part is played back. When set to “off,” the next Arpeggio starts as soon as you trigger it.
Settings: off, 60 (32nd note), 80 (16th note triplet), 120 (16th note), 160 (8th note triplet), 240 (8th note), 320 (1/4 note triplet), 480 (1/4
note)
A. Func 1 Mode (Assignable Function 1 Mode)
A. Func 2 Mode (Assignable Function 2 Mode)
Determines whether the ASSIGNABLE FUNCTION [1] and [2] buttons functions as a latch type or momentary type.
When set to “latch,” pressing the button alternates the lamp status between on and off. When set to “momentary,”
pressing/holding the button turns the lamp on and releasing the button turns the lamp off.
Settings: momentary, latch
Cutoff
Raises or lowers the cutoff frequency of the low pass filter to adjust the tone brilliance. The sound can be brightened by
raising the cutoff frequency, and darkened or muffled by lowering it. This parameter can be changed via the Knob
directly.
Settings: -64 – +0 – +63
Resonance
Determines the emphasis given to the Cutoff Frequency to add further character to the sound. Higher values result in a
more pronounced effect. This can be used in combination with the cutoff frequency parameter to add further character
to the sound. This parameter can be changed via the Knob directly.
Settings: -64 – +0 – +63
FEG Attack/Decay/Release/Depth (FEG Attack Time/Decay Time/Release Time/Depth)
Determines the FEG (Filter Envelope Generator) parameters for each Part. Using the Filter EG, you can control the
transition in tonal color (Cutoff Frequency) from the moment the sound starts to the moment the sound stops. The
settings made here will be applied to the same parameters in the Filter EG (page 51) of each Voice as offset. “FEG
Sustain” is not available here.
Settings: -64 – +0 – +63
AEG Attack/Decay/Sustain/Release (AEG Attack Time/Decay Time/Sustain Level/Release Time)
These can be used to control the change in volume from the moment a note is played to the moment the sound stops.
The settings mode here will be applied to the same parameters in the Amplitude EG (page 62) of each Part as offset.
Each of the AEG parameters can be changed directly via the Knob.
Settings: -64 – +0 – +63
4 Controller
5 Filter/EG