Owner's Manual
Table Of Contents
- Owners Manual
- Reset
- Table of Contents
- Features
- HDMI Information
- Supplied Accessories
- Parts & Controls
- Connections
- Getting Started
- Basic Operation
- Advanced Setup / Menu Operation
- Remote Control Operation
- Troubleshooting
- Glossary
- Specs
- Remote Control Codes
- Index
- Correction to Manual
- Front Panel Diagram
- Remote Control Diagram
- XM Channel Guide
- Warranty
IMPORTANT
SAFETY
INSTRUCTIONS
ANTENNA
LEAD
IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEe SECTION 810-20)
GROUNDING
CONDUCTORS
(NEC
SEcnON
810-21)
o-o,-~=-
GROUND CLAMPS
MAST
EXAMPLE
OF
ANTENNA GROUNDING
NEe
- NATIONAL
ELECTRICAL
CODE
~
POWER
SERViCE
GROUNDING
-=-
ELECTRODE
SYSTEM
(NEe
ART
250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
Outdoor Antenna Grounding -
If
an outside antenna
or
cable system is connected to the product, be sure the antenna
or
cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810
of
the National Electrical Code, ANSIINFPA 70,
provides information with regard to proper grounding
of
the
mast and supporting structure, grounding
of
the lead-in wire
to an antenna discharge unit, size
of
grounding conductors,
location
of
antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
24
d)
If
the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment
of
other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e)
If
the product has been dropped
or
damaged in any
way,
and
f)
When
the product exhibits a distinct change in perfor-
mance - this indicates a need for service.
20 Replacement Parts - When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer
or
have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock,
or
other
hazards.
21
Safety
Check
- Upon completion
of
any service
or
repairs to
this product, ask the service technician to perform safety
checks to determine that the product
is
in proper operating
condition.
22 Wall
or
Ceiling Mounting -
The
unit should be mounted
to a wall
or
ceiling only as recommended by the
manufacturer.
23 Heat -
The
product should be situated away from heat
sources such as radiators, heat registers, stoves,
or
other
products (including amplifiers) that produce heat.
Note
to
CATV system installer:
This reminder is provided to call the CATV system
installer's attention to Article 820-40
of
the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system
of
the building, as
close to the point
of
cable entry as practical.
FCC INFORMATION (for US customers)
IMPORTANT
NOTICE:
DO
NOT
MODIFY
THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2
IMPORT
ANT:
When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3
NOTE:
This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part
15
for Class
"B"
digital devices. Compliance with these
requirements provides a reasonable level
of
assurance that
your use
of
this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and,
if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation
of
other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not
occur
in
all installations.
If
this
product is found to be the source
of
interference, which
can be determined by turning the unit
"OFF'
and
"ON",
please try to eliminate the problem by using one
of
the
following measures:
Relocate either this product
or
the device that
is
being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker
or
fuse) circuits
or
install AC line filter/so
In the case
of
radio
or
TV interference, relocate/reorient
the antenna.
If
the antenna lead-in is
300
ohm
ribbon lead,
change the lead-in to coaxial type cable.
If
these corrective measures
do
not produce satisfactory
results, please contact the local retailer authorized to
distribute this type
of
product.
If
you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A.
6660
Orangethorpe Ave., Buena Park,
CA
90620.
The above statements apply ONLY to those products
distributed
by
Yamaha Corporation
of
America
or
its
subsidiaries.
Caution-ii En