Owner's Manual

49 En
Changing various settings of this unit (SETUP menu)
English
INTRODUCTION
ADDITIONAL
INFORMATION APPENDIX
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
Crossover Freq.
Sets the lower limit of the low frequency component
output from a speaker with a size set to “Small (SMLx1/
SMLx2).” Sound with a frequency below that limit is
output from a subwoofer or front speakers.
y
• If your subwoofer has a volume control or a crossover frequency control,
set the volume to half or the crossover frequency at the maximum.
Subwoofer Phase
Sets the phase of your subwoofer if bass sounds are
lacking or unclear.
■
B)Level
Separately adjusts volume of each speaker so that the
sounds from speakers are at the same volume at the
listening position. Items to be displayed vary depending
on the number of speakers connected.
y
• When only one surround back speaker is connected, “SB” appears
instead of “SBL” and “SBR.”
• You can adjust the volume listening to test tones when you set “E)Test
Tone” to “On” (see page 49).
• If your subwoofer has a volume control or a crossover frequency control,
set the volume to half or the crossover frequency at the maximum.
■ C)Distance
Adjusts timing at which each speaker outputs sound so
that sounds from speakers reach the listening position at
the same time. Set the unit (Unit) first and then the
distance of each speaker.
Unit
Front L
/ Front R / Center / Sur. L /
Sur. R / Sur.B L / Sur.B R / SWFR/
PRNS L/ PRNS R
y
• Different items are displayed depending on settings of “A)Config”
(see page 47).
• When only one surround back speaker is connected, “Sur.B” appears
instead of “Sur.B L” and “Sur.B R.”
■ D)Equalizer
Adjusts sound quality and tone using a parametric graphic
equalizer.
EQ Type Select
Selects an equalizer type.
GEQ
Adjusts sound quality of each speaker using a graphic
equalizer. The graphic equalizer of this unit can adjust
signal levels in 7 frequency ranges.
To adjust the signal level within each range, select the
desired speaker with kCursor l / h while “→” is
displayed next to “Channel,” then the desired frequency
band with kCursor k / n, and adjust the signal level
with kCursor l / h.
■
E)Test Tone
Switches test tones on and off. To generate test tones
select “On” using kCursor l / h. When “On” is
selected, you can adjust the settings of “2 Manual Setup”
while listening to a test tone.
You can set various items for sound outputs.
y
• The default settings are marked with “*.”
■ 1 Dynamic Range
Selects the dynamic range adjustment method for
reproducing bitstream signals.
Choices: 40Hz/60Hz/80Hz*/90Hz/100Hz/110Hz/120Hz/
160Hz/200Hz
Choices: Normal*/Reverse
Normal Select this not to change the phase of your
subwoofer.
Reverse Select this to reverse the phase of your
subwoofer.
Adjustable range: -10.0dB to +10.0dB (0.5 dB steps)
Defaults: “FR.L/FR.R/SWFR/PR.L/PR.R” 0dB
“CNTR/SUR.L/SUR.R/SBL/SBR” -1.0dB
Choices: meters (m)*/feet (ft)
meters (m) Displays the speaker distance in meters.
feet (ft) Displays the speaker distance in feet.
Adjustable range: 0.30m to 24.00m (1.0ft to 80.0ft)
Defaults: 3.00m (10.0ft) “Front L/Front R/
SWFR/PRNS L/PRNS R”
2.60m (8.5ft) “Center”
2.40m (8.0ft) “Sur. L/Sur. R/
Sur.B L/Sur.B R/PRNS L/PRNS R”
Choices: Auto PEQ/GEQ*/Off
Auto PEQ Uses a parametric equalizer selected in
“1 Auto Setup.” Characteristics of the
currently used parametric equalizer
(see page 21) are displayed below “Auto
PEQ.”
If Auto Setup is not executed, this
parameter is not displayed.
GEQ Adjusts tone using a graphic equalizer. To
display the adjustment menu, press
kENTER.
Off Not use a graphic equalizer.
Choices: 63Hz/160Hz/400Hz/1kHz/2.5kHz/
6.3kHz/16kHz
Adjustable range: -6.0dB to 0dB* to +6.0dB (0.5 dB steps)
Choices: Off*/On
Off Does not generate test tones.
On Generates test tones.
Sound Setup
Choices: Min/Auto/STD/Max*
Min/Auto (Min) Sets the dynamic range suitable for
low volume or a quiet environment, such as
at night, for bitstream signals except for
Dolby TrueHD signals.
(Auto) Adjusts the dynamic range for Dolby
TrueHD signals based on input signal
information.
STD Sets the standard dynamic range
recommended for regular home use.
Max Outputs sound without adjusting the
dynamic range of the input signals.