manual

51
English
ADVANCED
OPERATION
Using the test tone
Use the test tone to set speaker levels so that the volume
from each speaker is identical when heard from your
listening position.
1 Press AMP to set the remote control in AMP
mode.
Check that “AMP” is showing on the remote control
display.
2 Press TEST.
The unit will output a test tone.
3 Press u / d repeatedly to select a speaker
to adjust.
Each time you press d, the unit will cycle through
the speakers in the following order:
TEST LEFT(main L)→TEST CENTER(center)→TEST
RIGHT(main R)→TEST R SUR.(rear R)→TEST
REAR CNTR(rear center)→TEST L SUR.(rear
L)→TEST SUBWOOFER(subwoofer)→.....
(Press u to cycle the speakers in the reverse order.)
4 Press j / i to adjust speaker volumes.
5 Press TEST when you have completed your
adjustment.
The test tone halts.
Notes
• You cannot enter test mode if headphones are connected to the
PHONES jack. Remove the headphones from the PHONES
jack.
• You cannot adjust speaker volumes if the “SOUND 1
SPEAKER SET” parameter on the set menu is set to NON.
• You cannot adjust the subwoofer level if the “1E BASS”
parameter in “SOUND 1 SPEAKER SET” in the set menu is
set to MAIN.
• If you select “BASIC 1 SETUP” in the set menu and then
select “SET”, speaker levels change in response to any
changes you make in “BASIC 1 SETUP”.
y
• Depending on the source the unit is reproducing, the speaker
levels set with the test tone may not be to your liking. If this is
the case, adjust the speaker levels while listening to the
source.
SETTING THE SPEAKER LEVELS
Adjusting the volume during
playback
You can adjust the volume of the speakers while listening
to sound playback.
1 Press AMP to set the remote control in AMP
mode.
Check that “AMP” is showing on the remote control
display.
2 Press LEVEL repeatedly to select the
speaker you want to adjust.
The unit cycles through the speakers in the following
order each time you press LEVEL:
MAIN L→CENTER→MAIN R→R SUR.
(rear R)→REAR CT (rear center)→L SUR.
(rear L)→SWFR (subwoofer)→.....
y
• Pressing LEVEL once opens the level display. Press u / d at
this time to select a speaker.
3 Press j / i to adjust the speaker volume.
• The center and rear speakers can be adjusted by a
maximum of –10dB ~ +10dB.
• The main speakers and subwoofer can be adjusted
by a maximum of –20dB ~ 0dB.
Notes
• You cannot adjust speaker levels if the “SOUND 1 SPEAKER
SET” parameter in the set menu is set to NON.
• You cannot adjust the subwoofer level if the “1E BASS”
parameter in “SOUND 1 SPEAKER SET” in the set menu is
set to MAIN.
• If you use LEVEL to adjust speaker levels, the speaker levels
you previously set with the test tone will also change.
• If you select “BASIC 1 SETUP” in the set menu and then
select “SET”, speaker levels change in response to any
changes you make in “BASIC 1 SETUP”.
DISC SKIP
POWER
TV
AMP
REC
AUDIO
VOL
TV INPUT
SET MENU
A/B/C/D/E
LEVEL
TITLE
TV VOL
TV VOL
TV MUTE
SELECT
MENU
MUTE
CH
TEST
ON SCREEN
STEREO
EFFECT
DISPLAYRETURN
CH
PRESET PRESET
ROCK ENTER-
POWER
AV
3
1
2
DISC SKIP
POWER
TV
AMP
REC
AUDIO
VOL
TV INPUT
SET MENU
A/B/C/D/E
LEVEL
TITLE
TV VOL
TV VOL
TV MUTE
SELECT
MENU
MUTE
CH
TEST
ON SCREEN
STEREO
EFFECT
DISPLAYRETURN
CH
PRESET PRESET
ROCK ENTER-
POWER
AV
2,5
3
4
1
0109RX-V740_46-53_EN-U.p65 03.1.10, 6:35 PM51