Owner's Manual
Table Of Contents
- English
- INTRODUCTION
- PREPARATION
- Preparing remote control
- Connections
- Placing speakers
- Connecting speakers
- Information on jacks and cable plugs
- Connecting a TV monitor or projector
- Connecting other components
- Connecting a Yamaha iPod universal dock or Bluetooth™ wireless audio receiver
- Connecting a USB storage device
- Using the VIDEO AUX jacks
- Connecting the FM and AM antennas
- Connecting the power cable
- Turning this unit on and off
- Optimizing the speaker setting for your listening room (YPAO)
- BASIC OPERATION
- ADVANCED OPERATION
- APPENDIX
- Français
- INTRODUCTION
- PRÉPARATIONS
- Préparation du boîtier de télécommande
- Raccordements
- Disposition des enceintes
- Raccordements des enceintes
- Information sur les prises et les fiches des câbles
- Raccordement d'un moniteur TV ou d'un projecteur
- Raccordement d’autres appareils
- Raccordement d'une station universelle Yamaha iPod ou d'un ampli-syntoniseur Bluetooth™ sans fil
- Raccordement d'un périphérique de stockage USB
- Utilisation des prises VIDEO AUX
- Raccordement des antennes FM et AM
- Raccordement du câble d'alimentation
- Mise en ou hors service de cet appareil
- Optimisation du réglage des enceintes pour votre salle d'écoute (YPAO)
- OPÉRATIONS DE BASE
- Lecture
- Opérations de base
- Utilisation de la fonction SCENE
- Sélection d’une source sur l’écran GUI
- Mise en sourdine du son
- Réglage des aigus/graves (correction de tonalité)
- Écoute du son pur en hi-fi
- Utilisation d’un casque
- Affichage des informations concernant le signal d’entrée
- Modification des informations sur l’afficheur de la face avant
- Des corrections de champ sonore pour tous les goûts
- Sélection d’une correction de champ sonore
- Écoute de sources d’entrée non traitées (mode de décodage direct)
- Utilisation des corrections de champ sonore sans enceintes d’ambiance (Virtual CINEMA DSP)
- Écoutez des corrections de champ sonore avec un casque (SILENT CINEMA™)
- Utilisation du mode CINEMA DSP 3D
- Syntonisation FM/AM
- Utilisation d’un iPod™
- Utilisation d’appareils Bluetooth™
- Connexion de périphériques de stockage USB
- Autres fonctions
- Lecture
- OPÉRATIONS DÉTAILLÉES
- Réglage du menu d’option pour chaque source d’entrée (menu Option)
- Édition de décodeurs d’ambiance/corrections de champ sonore
- Utilisation de divers réglages pour cet appareil (menu Setup)
- Utilisation d'une configuration multi-zones
- Commande d’autres périphériques avec la télécommande
- Réglages approfondis
- APPENDICE
- Information about software
- List of remote control codes
63 En
Troubleshooting
English
INTRODUCTION
APPENDIX
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
E-7:NO MIC The optimizer microphone was
unplugged during the “Auto Setup”
procedure.
Do not touch the optimizer microphone during “Auto
Setup”.
20
E-8:NO SIGNAL The optimizer microphone does not
detect test tones.
Check whether the microphone is properly placed. 20
Check whether the speakers are properly placed and
connected.
10, 11
The optimizer microphone or OPTIMIZER MIC
jack may be defective. Contact the nearest Yamaha
dealer or service center.
—
E-9:USER CANCEL “Auto Setup” was canceled due to an
inappropriate user operation.
Run “Auto Setup” again. 20
E-10:INTERNAL
ERROR
An internal error occurred. Run “Auto Setup” again. 20
After Auto Setup
Error message Cause Remedy
See
page
W-1:OUT OF PHASE Speaker polarity is not correct. This
message may appear depending on the
speakers even when the speakers are
connected correctly.
Check the polarities (+, –) of the displayed speaker.
If they are correct, the speakers work properly even
when this message is displayed.
12
W-2:OVER 24m (80ft) The distance between the speaker and the
listening position is over 24 m (80 ft).
Bring the speaker within 24 m (80 ft.) area around
the listening position.
—
W-3:LEVEL ERROR The difference of volume level among
speakers is excessive.
Recheck the speaker positions and make sure all
speakers are placed in a similar environment.
—
Check the polarities (+, –) of the speakers. 12
We recommended that you use speakers with the
same or similar specifications.
—
Adjust the output volume of the subwoofer. —
W-4:CHECK PRNS Presence speakers were not detected
during measurement with “Extra Speaker
Assignment” set to “Presence”.
Check the presence speaker connections and perform
measurement again. If presence speakers are not
connected, set the “Extra Speaker Assignment” to
other than “Presence”.
11, 46
Error message Cause Remedy
See
page