Owner's Manual
Table Of Contents
- English
- INTRODUCTION
- PREPARATION
- Preparing remote control
- Connections
- Placing speakers
- Connecting speakers
- Information on jacks and cable plugs
- Connecting a TV monitor or projector
- Connecting other components
- Connecting a Yamaha iPod universal dock or Bluetooth™ wireless audio receiver
- Connecting a USB storage device
- Using the VIDEO AUX jacks
- Connecting the FM and AM antennas
- Connecting the power cable
- Turning this unit on and off
- Optimizing the speaker setting for your listening room (YPAO)
- BASIC OPERATION
- ADVANCED OPERATION
- APPENDIX
- Français
- INTRODUCTION
- PRÉPARATIONS
- Préparation du boîtier de télécommande
- Raccordements
- Disposition des enceintes
- Raccordements des enceintes
- Information sur les prises et les fiches des câbles
- Raccordement d'un moniteur TV ou d'un projecteur
- Raccordement d’autres appareils
- Raccordement d'une station universelle Yamaha iPod ou d'un ampli-syntoniseur Bluetooth™ sans fil
- Raccordement d'un périphérique de stockage USB
- Utilisation des prises VIDEO AUX
- Raccordement des antennes FM et AM
- Raccordement du câble d'alimentation
- Mise en ou hors service de cet appareil
- Optimisation du réglage des enceintes pour votre salle d'écoute (YPAO)
- OPÉRATIONS DE BASE
- Lecture
- Opérations de base
- Utilisation de la fonction SCENE
- Sélection d’une source sur l’écran GUI
- Mise en sourdine du son
- Réglage des aigus/graves (correction de tonalité)
- Écoute du son pur en hi-fi
- Utilisation d’un casque
- Affichage des informations concernant le signal d’entrée
- Modification des informations sur l’afficheur de la face avant
- Des corrections de champ sonore pour tous les goûts
- Sélection d’une correction de champ sonore
- Écoute de sources d’entrée non traitées (mode de décodage direct)
- Utilisation des corrections de champ sonore sans enceintes d’ambiance (Virtual CINEMA DSP)
- Écoutez des corrections de champ sonore avec un casque (SILENT CINEMA™)
- Utilisation du mode CINEMA DSP 3D
- Syntonisation FM/AM
- Utilisation d’un iPod™
- Utilisation d’appareils Bluetooth™
- Connexion de périphériques de stockage USB
- Autres fonctions
- Lecture
- OPÉRATIONS DÉTAILLÉES
- Réglage du menu d’option pour chaque source d’entrée (menu Option)
- Édition de décodeurs d’ambiance/corrections de champ sonore
- Utilisation de divers réglages pour cet appareil (menu Setup)
- Utilisation d'une configuration multi-zones
- Commande d’autres périphériques avec la télécommande
- Réglages approfondis
- APPENDICE
- Information about software
- List of remote control codes
58 En
Troubleshooting
No sound is heard
from the subwoofer.
“LFE / Bass Out” is set to “Front” and a
Dolby Digital, DTS or AAC signals is
being played.
Set “LFE / Bass Out” to “Subwoofer” or “Both”. 46
“LFE / Bass Out” is set to “Subwoofer” or
“Front” and a 2-channel source is being
played.
Set “LFE / Bass Out” to “Both”. 46
The source does not contain low
frequency signals.
No sound is heard
from the surround
back speakers.
“Extended Surround” in the Option menu
is set to “Off”, or an input signal does not
contain a surround back flag with
“Extended Surround” set to “Auto”.
Set “Extended Surround” other than “Off” or “Auto”. 38
The audio input
sources cannot be
played in the desired
digital audio signal
format.
The connected component is not set to
output the desired digital audio signals.
Set the playback component properly referring to its
operating instructions.
—
Noise/hum noise is
heard.
Incorrect cable connection. Connect the audio cables properly. If the problem
persists, the cables may be defective.
—
A DTS-CD is being played back. 1) When only noise is output
If a DTS bitstream signal is not properly input to this
unit, only noise is output. Connect the playback
component to this unit by digital connection and play
back the DTS-CD. If the condition is not improved,
the problem may results from the playback
component. Consult the manufacturer of the playback
component.
2) When noise is output during playback or skip
operation
Before playing back the DTS-CD, display the Option
menu after selecting the input source and set
“Decoder Mode” to “DTS”.
15, 38
The volume level
cannot be increased,
or the sound is
distorted.
The component connected to the AUDIO
1/2 jacks of this unit is turned off.
Turn on the power of the component. 53
“Memory Guard!” is
displayed and the
setting cannot be
changed.
“Memory Guard” in “Set Menu” is set to
“On”.
Set “Memory Guard” to “Off”. 50
There is noise
interference from
digital or radio
frequency equipment.
This unit is too close to other digital or
radio frequency equipment.
Move this unit further away from such equipment. —
Problem Cause Remedy
See
page