Owner's Manual
Table Of Contents
- English
- INTRODUCTION
- PREPARATION
- Preparing remote control
- Connections
- Placing speakers
- Connecting speakers
- Information on jacks and cable plugs
- Connecting a TV monitor or projector
- Connecting other components
- Connecting a Yamaha iPod universal dock or Bluetooth™ wireless audio receiver
- Connecting a USB storage device
- Using the VIDEO AUX jacks
- Connecting the FM and AM antennas
- Connecting the power cable
- Turning this unit on and off
- Optimizing the speaker setting for your listening room (YPAO)
- BASIC OPERATION
- ADVANCED OPERATION
- APPENDIX
- Français
- INTRODUCTION
- PRÉPARATIONS
- Préparation du boîtier de télécommande
- Raccordements
- Disposition des enceintes
- Raccordements des enceintes
- Information sur les prises et les fiches des câbles
- Raccordement d'un moniteur TV ou d'un projecteur
- Raccordement d’autres appareils
- Raccordement d'une station universelle Yamaha iPod ou d'un ampli-syntoniseur Bluetooth™ sans fil
- Raccordement d'un périphérique de stockage USB
- Utilisation des prises VIDEO AUX
- Raccordement des antennes FM et AM
- Raccordement du câble d'alimentation
- Mise en ou hors service de cet appareil
- Optimisation du réglage des enceintes pour votre salle d'écoute (YPAO)
- OPÉRATIONS DE BASE
- Lecture
- Opérations de base
- Utilisation de la fonction SCENE
- Sélection d’une source sur l’écran GUI
- Mise en sourdine du son
- Réglage des aigus/graves (correction de tonalité)
- Écoute du son pur en hi-fi
- Utilisation d’un casque
- Affichage des informations concernant le signal d’entrée
- Modification des informations sur l’afficheur de la face avant
- Des corrections de champ sonore pour tous les goûts
- Sélection d’une correction de champ sonore
- Écoute de sources d’entrée non traitées (mode de décodage direct)
- Utilisation des corrections de champ sonore sans enceintes d’ambiance (Virtual CINEMA DSP)
- Écoutez des corrections de champ sonore avec un casque (SILENT CINEMA™)
- Utilisation du mode CINEMA DSP 3D
- Syntonisation FM/AM
- Utilisation d’un iPod™
- Utilisation d’appareils Bluetooth™
- Connexion de périphériques de stockage USB
- Autres fonctions
- Lecture
- OPÉRATIONS DÉTAILLÉES
- Réglage du menu d’option pour chaque source d’entrée (menu Option)
- Édition de décodeurs d’ambiance/corrections de champ sonore
- Utilisation de divers réglages pour cet appareil (menu Setup)
- Utilisation d'une configuration multi-zones
- Commande d’autres périphériques avec la télécommande
- Réglages approfondis
- APPENDICE
- Information about software
- List of remote control codes
54 En
In the advanced setup menu, you can set basic operations
of this unit, such as on and off of a bi-amp connection, or
initialize user settings.
1 Set this unit to standby.
2 While holding down OSTRAIGHT on the
front panel, press KMAIN ZONE ON/OFF.
Keep holding down OSTRAIGHT until
“ADVANCED SETUP” appears on the front panel
display.
3 Rotate the NPROGRAM selector to select
the parameter you want to change.
The default setting are marked with “*”.
y
• Set values are placed in XXX of the following parameters on an
actual display screen.
SP IMP. -XXX
Selects output impedance of this unit according to
connected speakers. When you connect 4-ohm
speakers to the FRONT speaker terminals, set “SP
IMP.” to “6ΩMIN.”.
REMOTE ID -XXX
Sets a remote control ID. When using multiple
Yamaha AV receivers, you can operate them with a
single remote control by setting the receiver IDs to
the same setting.
BI AMP - XXX
Switches on and off of bi-amp connection of main
speakers. For bi-amp connection, see page 12.
SCENE IR -XXX
Selects whether or not to transmit the control signals
to an external component connected to the REMOTE
OUT jack on this unit when BD/DVD or CD SCENE
function is selected.
MON.CHK - XXXX
Adds upscaling limitation on output signals to a video
monitor connected to this unit via the HDMI OUT
jack.
INIT-XXXXXXXXX
Initializes various settings stored in this unit. You can
select an initialization method from the following.
DSP PARAM: All parameters of sound field
programs
VIDEO Video conversion settings (resolution/
aspect) in the Setup menu and the GUI
display position
ALL All
CANCEL Cancellation of initialization
4 Press OSTRAIGHT repeatedly to change
the selected parameter setting.
To change other settings, repeat steps 3 and 4.
5 Press KMAIN ZONE ON/OFF to set this
unit to standby.
The settings you made are reflected next time you
turn on this unit.
You can check the firmware of this unit and update the
firmware using the USB port on the front panel.
Select the following parameter in step 3 above.
FIRM UPDATE
Updates the firmware of this unit. To update the firmware,
select “FIRM UPDATE” and then press OSTRAIGHT.
Notes
• Do not use this feature unless you need to update the firmware.
• Be sure to read information supplied with updates before updating the
firmware.
VERXXX.XXX.XXX
Displays the firmware of this unit.
Two IDs are provided for the remote control of this unit. If
another Yamaha amplifier is in the same room, setting a
different remote control ID to this unit prevents unwanted
operation of the other amplifier.
“ID1” is set for both the main unit and remote control by
default. If you have changed the remote control ID, make
sure that you select the same ID for the main unit in the
the advanced setup menu.
1 Press oCODE SET on the remote control
using a pointed object such as the tip of a
ballpoint pen.
nTRANSMIT blinks twice.
2 Press iON SCREEN.
Advanced setup
Choices: 6ΩMIN, 8ΩMIN*
Choices: ID1*, ID2
Choices: ON, OFF*
Choices: ON*, OFF
Choices: YES*, SKIP
Choices: DSP PARAM, VIDEO, ALL, CANCEL*
ADVANCEDSETUP
Updating the firmware
Setting a remote control ID