Owner's Manual
Table Of Contents
- English
- INTRODUCTION
- PREPARATION
- Preparing remote control
- Connections
- Placing speakers
- Connecting speakers
- Information on jacks and cable plugs
- Connecting a TV monitor or projector
- Connecting other components
- Connecting a Yamaha iPod universal dock or Bluetooth™ wireless audio receiver
- Connecting a USB storage device
- Using the VIDEO AUX jacks
- Connecting the FM and AM antennas
- Connecting the power cable
- Turning this unit on and off
- Optimizing the speaker setting for your listening room (YPAO)
- BASIC OPERATION
- ADVANCED OPERATION
- APPENDIX
- Français
- INTRODUCTION
- PRÉPARATIONS
- Préparation du boîtier de télécommande
- Raccordements
- Disposition des enceintes
- Raccordements des enceintes
- Information sur les prises et les fiches des câbles
- Raccordement d'un moniteur TV ou d'un projecteur
- Raccordement d’autres appareils
- Raccordement d'une station universelle Yamaha iPod ou d'un ampli-syntoniseur Bluetooth™ sans fil
- Raccordement d'un périphérique de stockage USB
- Utilisation des prises VIDEO AUX
- Raccordement des antennes FM et AM
- Raccordement du câble d'alimentation
- Mise en ou hors service de cet appareil
- Optimisation du réglage des enceintes pour votre salle d'écoute (YPAO)
- OPÉRATIONS DE BASE
- Lecture
- Opérations de base
- Utilisation de la fonction SCENE
- Sélection d’une source sur l’écran GUI
- Mise en sourdine du son
- Réglage des aigus/graves (correction de tonalité)
- Écoute du son pur en hi-fi
- Utilisation d’un casque
- Affichage des informations concernant le signal d’entrée
- Modification des informations sur l’afficheur de la face avant
- Des corrections de champ sonore pour tous les goûts
- Sélection d’une correction de champ sonore
- Écoute de sources d’entrée non traitées (mode de décodage direct)
- Utilisation des corrections de champ sonore sans enceintes d’ambiance (Virtual CINEMA DSP)
- Écoutez des corrections de champ sonore avec un casque (SILENT CINEMA™)
- Utilisation du mode CINEMA DSP 3D
- Syntonisation FM/AM
- Utilisation d’un iPod™
- Utilisation d’appareils Bluetooth™
- Connexion de périphériques de stockage USB
- Autres fonctions
- Lecture
- OPÉRATIONS DÉTAILLÉES
- Réglage du menu d’option pour chaque source d’entrée (menu Option)
- Édition de décodeurs d’ambiance/corrections de champ sonore
- Utilisation de divers réglages pour cet appareil (menu Setup)
- Utilisation d'une configuration multi-zones
- Commande d’autres périphériques avec la télécommande
- Réglages approfondis
- APPENDICE
- Information about software
- List of remote control codes
38 En
Setting the option menu for each input source (Option menu)
Decoder Mode
Selects DTS digital audio signals for reproduction.
Extended Surround
Selects whether to reproduce multi-channel input signals
in 6.1- or 7.1-channel when surround back speakers are
used.
Signal Info
Displays information on audio and video signals on the
GUI screen and front panel display. You can change items
to be displayed using jCursor k / n.
• Audio information
•
Notes
• “No Signal” is displayed when no signals are input and “---” is displayed
when signals that this unit cannot recognize are input.
• The bit rate may vary during playback.
• Video information
•
• HDMI error message
(appears only when an error has occurred)
•
FM Mode
Sets FM broadcasting receiving mode.
Auto Preset
Automatically detects FM radio stations and registers
them as preset stations (page 30).
Clear Preset
Clears preset station (page 31).
Shuffle
Changes the shuffle playback style.
Repeat
Changes the repeat playback style.
Input source: HDMI1-4, AV1-4
Choices: Auto*, DTS
Auto Automatically selects audio input signals.
DTS Selects DTS signals only. Other input signals
are not reproduced.
Input source: HDMI1-4, AV1-4
Choices: Auto*, PLIIxMovie, PLIIxMusic, EX/ES, Off
Auto Automatically selects the most suitable
decoder according to whether a flag for
reproducing surround back channel is present,
and reproduces the signals in 6.1- or 7.1-
channel.
PLIIx
Movie
Always reproduces signals in 6.1- or 7.1-
channel using the PLIIxMovie decoder
whether or not surround back channel signals
are contained. You can select this parameter
when two surround back speakers are
connected.
PLIIx
Music
Always reproduces signals in 6.1- or 7.1-
channel using the PLIIxMusic decoder whether
or not surround back channel signals are
contained. You can select this parameter when
one or two surround back speakers are
connected.
EX/ES Automatically selects the most suitable
decoder for input signals whether or not the
flag for reproducing surround back channel is
present, and always reproduces signals in 6.1-
channel.
Off Always reproduces original signals whether or
not the flag for reproducing surround back
channel is present.
Input source: HDMI1-4, AV1-4, USB
Format
Format of digital audio signals.
Channel
The number of input signal channels
(front/surround/LFE).
For example, if input signal channels are
3 front channels, 2 surrounds and LFE,
“3/2/0.1” is displayed.
If a channel that cannot be expressed as
the above, a total number of channels
such as “5.1ch” may be displayed.
Sampling
Frequency
The sampling frequency per second in
analog-to-digital conversion.
Bitrate
The bit rate of input signal per second.
Video In
Format and resolution of video input
signal.
Video Out
Format and resolution of video output
signal.
Message
Error messages about HDMI signals and
HDMI components. See the following for
details of the error messages.
HDCP Error
HDCP authentication failed.
Device Over
The number of HDMI components
connected is over the limit.
Out of Res.
The connected monitor is not compatible
with the video input signal.
Input source: TUNER
Choices: Stereo*, Mono
Stereo Receives in stereo mode.
Mono Receives in monaural mode. You can get a
better reception in monaural mode.
Input source: TUNER
Input source: TUNER
Input source: iPod (DOCK), USB
Choices: iPod (DOCK): Off*, Songs, Albums
USB: Off*, On
Input source: iPod (DOCK), USB
Choices: Off*, One, All