Owner's Manual
Table Of Contents
- English
- INTRODUCTION
- PREPARATION
- Preparing remote control
- Connections
- Placing speakers
- Connecting speakers
- Information on jacks and cable plugs
- Connecting a TV monitor or projector
- Connecting other components
- Connecting a Yamaha iPod universal dock or Bluetooth™ wireless audio receiver
- Connecting a USB storage device
- Using the VIDEO AUX jacks
- Connecting the FM and AM antennas
- Connecting the power cable
- Turning this unit on and off
- Optimizing the speaker setting for your listening room (YPAO)
- BASIC OPERATION
- ADVANCED OPERATION
- APPENDIX
- Français
- INTRODUCTION
- PRÉPARATIONS
- Préparation du boîtier de télécommande
- Raccordements
- Disposition des enceintes
- Raccordements des enceintes
- Information sur les prises et les fiches des câbles
- Raccordement d'un moniteur TV ou d'un projecteur
- Raccordement d’autres appareils
- Raccordement d'une station universelle Yamaha iPod ou d'un ampli-syntoniseur Bluetooth™ sans fil
- Raccordement d'un périphérique de stockage USB
- Utilisation des prises VIDEO AUX
- Raccordement des antennes FM et AM
- Raccordement du câble d'alimentation
- Mise en ou hors service de cet appareil
- Optimisation du réglage des enceintes pour votre salle d'écoute (YPAO)
- OPÉRATIONS DE BASE
- Lecture
- Opérations de base
- Utilisation de la fonction SCENE
- Sélection d’une source sur l’écran GUI
- Mise en sourdine du son
- Réglage des aigus/graves (correction de tonalité)
- Écoute du son pur en hi-fi
- Utilisation d’un casque
- Affichage des informations concernant le signal d’entrée
- Modification des informations sur l’afficheur de la face avant
- Des corrections de champ sonore pour tous les goûts
- Sélection d’une correction de champ sonore
- Écoute de sources d’entrée non traitées (mode de décodage direct)
- Utilisation des corrections de champ sonore sans enceintes d’ambiance (Virtual CINEMA DSP)
- Écoutez des corrections de champ sonore avec un casque (SILENT CINEMA™)
- Utilisation du mode CINEMA DSP 3D
- Syntonisation FM/AM
- Utilisation d’un iPod™
- Utilisation d’appareils Bluetooth™
- Connexion de périphériques de stockage USB
- Autres fonctions
- Lecture
- OPÉRATIONS DÉTAILLÉES
- Réglage du menu d’option pour chaque source d’entrée (menu Option)
- Édition de décodeurs d’ambiance/corrections de champ sonore
- Utilisation de divers réglages pour cet appareil (menu Setup)
- Utilisation d'une configuration multi-zones
- Commande d’autres périphériques avec la télécommande
- Réglages approfondis
- APPENDICE
- Information about software
- List of remote control codes
19 En
Connections
English
INTRODUCTION
ADDITIONAL
INFORMATION APPENDIX
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
After all connections are complete, plug the power cable
of this unit into an AC wall outlet.
1 Press KMAIN ZONE ON/OFF on the front
panel (or pPOWER on the remote control)
to turn on this unit.
2 Press KMAIN ZONE ON/OFF (or
pPOWER) again to turn off this unit
(standby mode).
y
• The unit needs a few seconds until ready to play back.
• You can also turn on this unit by pressing PSCENE (or hSCENE).
• This unit consumes a small amount of electricity even in the standby
mode. We recommend disconnecting the power cable from the AC wall
outlet.
Connecting the power cable
Turning this unit on and off
Caution
Do not unplug this unit while it is turned on. Doing so
may damage this unit or cause the settings of this unit
to be saved incorrectly.
C
LA
SS
2 WIRIN
G
N
E2
/
PRE
S
EN
CE
To the AC wall outlet
Power cable