Reference Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Correcting delay between channels (Input Delay)
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- MIDI Data Format
- Input/Output Specifications
- Electrical characteristics
- Mixer Basic Parameters
- Pin Assignment Chart
- MIDI Implementation Chart
Setup
Reference Manual
190
4 PAN LINK button
This button appears if SIGNAL TYPE is set to STEREO and the bus type is set to VARI. If
the button is on, the pan setting of signals sent from input channels to the
corresponding two buses will link with the STEREO bus pan setting.
5 Tabs
Enable you to switch between the MIX and MATRIX buses.
Switching the entire phantom power supply on/
off
NOTE
This +48V MASTER setting does not affect the inputs of external racks such as DANTE inputs
(I/O devices). Each rack has a +48V MASTER switch, and will operate according to its setting.
Specifying the brightness of the touch screen,
LEDs, channel name displays, and lamps
Follow the steps below to specify the brightness of the touch screen, top panel LEDs, channel
name displays, and lamps connected to the rear panel LAMP connectors. You can save two
different brightness settings in bank A and B, and switch between them rapidly if desired.
NOTE
You can also assign this parameter to a USER DEFINED key, and press that key to switch
between banks A and B.
SETUP screen (brightness setting field)
1 BANK A/B buttons
Switch between the brightness settings.
CONTRAST field
2
NAME
Adjusts the contrast of the characters of the channel name displays on the top panel.
BRIGHTNESS field
3
NAME
Adjusts the brightness of the channel name displays on the top panel.
This will also change the CH COLOR brightness and LED brightness in the lower part of
the [TOUCH AND TURN] knob. If you want to adjust the CH COLOR brightness after
setting the name display brightness, use the CH COLOR knob.
4 CH COLOR
Adjusts the brightness of the channel colors on the top panel.
This lets you apply a relative adjustment to only the channel color brightness without
changing the channel name display brightness.
STEP
1. In the Function Access Area, press the SETUP button to access the SETUP screen.
2. In the center of the SETUP screen, press the +48V MASTER field’s ON button or OFF
button.
If this button is off, phantom power will not be supplied even if the +48V button of an
OMNI jack input channel or TALKBACK IN is on.
SETUP screen
STEP
1. In the Function Access Area, press the SETUP button.
2. In the field located in the right of the bottom row of the SETUP screen, press the
BANK A or BANK B button.
3. Use the [TOUCH AND TURN] knob to adjust the brightness of each item.
1 2 3 4 5 6 7