User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Remount function to USB flash drives
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Setup
V5 Reference Manual
211
NOTE
• If no password has been set, you will simply be logged-in in step 6 when you press the LOAD
button.
• If the password was incorrect, a message of “Wrong Password!” will appear near the bottom of
the screen.
• If you have selected a user authentication key that was created on a different QL series console,
a keyboard window will appear, allowing you to enter the Administrator password of the QL series
console that you will be using. (If the Administrator passwords are identical, this window will not
appear.) When you enter the correct Administrator password, another keyboard window will
appear, allowing you to enter the password for the selected user. If you re-save the user
authentication key, you will not be asked for the Administrator password the next time. Refer to
“Editing a user authentication key” on page 211.
• For details about loading files from the USB flash drive, refer to “Loading a file from a USB flash
drive” on page 230.
Changing the password
Follow the steps below to change the password of the logged-in user. The Guest account
does not have a password.
NOTE
After you change the password, if you log out from the console without saving the user
authentication key, the changed password will be discarded.
Editing a user authentication key
If you are logged-in as a user, you can edit your preference settings, USER DEFINED keys,
USER DEFINED knobs, custom fader banks, master fader, comments, and password, and
save (overwrite) them onto your user authentication key. If you are logged-in as a Power User,
you can also change the user level.
NOTE
• If you are logged-in as a Power User, you can also change the user level.
• If you loaded a user authentication key from a USB flash drive, press the SAVE KEY button before
removing the USB flash drive. If you do remove the USB flash drive before pressing this button,
load the user authentication key again.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the PASSWORD CHANGE button.
3. In the keyboard window, enter the current password and press the OK button.
4. Enter the new password in the NEW PASSWORD field, then enter the same
password in the RE-ENTER PASSWORD field for verification, and finally press the OK
button.
5. Refer to “Editing a user authentication key” on page 211 to overwrite the user
authentication key.
STEP
1. Log in as a user, and edit the Preference settings (page 214), USER DEFINED keys
(page 216), USER DEFINED knobs (page 222), and CUSTOM FADER BANK
(page 224) settings.
2. Close the USER SETUP window.
3. In the SETUP screen, press the SAVE KEY button.
4. In the SAVE KEY window, choose the save-destination button, and then press the
SAVE TO button.
5. A dialog box will ask you to confirm that you want to overwrite that user
authentication key; press the OK button.
SETUP screen SAVE KEY window