User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Remount function to USB flash drives
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Graphic EQ, Parametric EQ, effects, and Premium Rack
V5 Reference Manual
156
EQ-1A
EQ-1A is a processor that emulates a famous passive-type vintage EQ. It features a unique
style of operation, allowing you to individually boost and attenuate (cut) each of two frequency
ranges (high and low). The frequency response is utterly unlike that of a conventional EQ, and
is a uniquely distinctive characteristic of this model. The input/output circuits and vacuum
tubes produce a tonal character that is highly musical and well-balanced.
1 IN switch
Turns the processor on or off.
When the switch is off, the signal will bypass the filter section, but pass through the
input/output transformer and amp circuits.
2 LOW FREQUENCY knob
Sets the frequency of the low range filter.
3 (LOW) BOOST knob
Sets the amount of boost applied to the frequency band specified by the LOW
FREQUENCY knob.
4 (LOW) ATTEN knob
Sets the amount of attenuation applied to the frequency band specified by the LOW
FREQUENCY knob.
5 BAND WIDTH knob
Sets the width of the frequency band controlled by the high range filter.
As you rotate the knob toward the right (Broad), the band will become wider and the
peak level will decrease. This affects only the response of the boost.
6 HIGH FREQUENCY knob
Sets the frequency of the high range filter. This affects only the response of the boost.
7 (HIGH) BOOST knob
Sets the amount of boost applied to the frequency band specified by the HIGH
FREQUENCY knob.
8 (HIGH) ATTEN knob
Sets the amount of attenuation applied to the frequency band specified by the ATTEN
SEL knob.
9 (HIGH) ATTEN SEL knob
Switches the frequency region attenuated by the ATTEN knob.
Dynamic EQ
Dynamic EQ is a newly-developed equalizer that does not emulate any specific model of
equalizer. The sidechain has a filter that extracts the same frequency band as the EQ. This
allows you to apply EQ in the same way as you might apply a compressor or expander to a
specific frequency region, causing the EQ gain to vary dynamically only when a specific
frequency region of the input signal becomes too high or too low. For example you could use
this on a vocal sound as a de-esser, so that EQ is applied to a specific frequency band only
when sibilance or high-frequency consonants reach an unpleasant level, thus preserving a
natural sound that does not impair the original tonal character. Two full-band Dynamic EQs
are provided, enabling you to process a wide range of audio sources.
1 BAND ON/OFF button
Turns each band on or off.
2 61
3 4 5 7 8 9
82A
4
3
1
9
0
6
5
7B
C