User Manual
Table Of Contents
- Introduction
- Audio Components
- The Difference Between Mono, Stereo, and Multi
- How to Control Control Signals
- Acoustic Echo Canceller (AEC)
- Ambient Noise Compensator (ANC)
- Audio Detector
- Auto Gain Control (AGC)
- Combiner
- Room Combiner/Room Combiner plus Automixer
- ■ “Room Combiner” component editor/”Room Combiner plus Automixer” component editor
- ■ “Room Combiner” component editor/”Room Combiner plus Automixer” component editor
- Combiner parameter setting window (Room Combiner)
- Combiner parameter setting window (Room Combiner plus Automixer)
- Control
- Control
- Dugan Automixer window (Room Combiner plus Automixer)
- Room Combiner/Room Combiner plus Automixer
- DCA
- Delay
- Dynamics
- REV-X
- EQ
- Fader
- Feedback Suppressor
- Filter
- Input/Output
- Meter
- Mixer
- Oscillator
- Polarity
- Probe
- Router
- Source Selector
- Speaker Processor
- Control Components
- Control Methods for Control Components
- Trigger
- Button (Normalized Value)
- Button (Value)
- Radio Button (Normalized Value)
- Radio Button (Value)
- Fader (Normalized Value)
- Fader (Value)
- Processing
- Logic (Normalized Value)
- NOT (Normalized Value)
- Flip-Flop (Normalized Value)
- Invert (Normalized Value)
- Compare (Normalized Value)
- Difference (Normalized Value)
- Max/Min (Normalized Value)
- Negate (Value)
- Compare (Value)
- Multi Compare (Value)
- Difference (Value)
- Max/Min (Value)
- Delay
- External Events
- Suspend
- Router
- Other
- GPI In
- GPI Out
ProVisionaire Design DME7 Component Guide
53
a
Paging Ducker [ON] button
Switches the paging ducker function between enabled and disabled.
b
TRIGGER [ON] button
If you turn this on, the audio signal level of the program source is lowered to the value
specified by the [RANGE] knob. If you turn this off, the audio signal level of the program
source returns to its original level. Set this so that it operates in tandem with the talk
switch/button of the paging mic.
c
[RANGE] knob/indicator
The knob sets the audio signal level of the program source when the TRIGGER [ON]
button is on. The indicator is lit when the signal decreases to the level specified by the
knob. If you attach an LED to GPI and register the [RANGE] indicator to GPI, you’ll be able
to check whether the paging mic is active.
d [ATTACK] knob
Specifies the time over which the audio signal level of the program source decreases to
the level specified by the [RANGE] knob, starting when the TRIGGER [ON] button turns on.
e [HOLD] knob
Specifies the time after which the audio signal level of the program source starts
returning to the original level after the TRIGGER [ON] button turns off.
f
[RELEACE] knob
Specifies the time over which the audio signal level of the program source returns to the
original level after the time specified by the [HOLD] knob.
g [OUTPUT] meter
Shows the output signal level.
Control
Parameter types of the input/output values for each Port
Input Value
Control Parameter Output Value
Type Range
Input Port Name Parameter Range
Output Port Name Type Range
Value Num 0,1
●
On OFF:0, ON:1
●
On Value Num
OFF:0,
ON:1
Value Num 0,1
●
Trigger OFF:0, ON:1
●
Trigger Value Num
OFF:0,
ON:1
Value dB
−∞–
10.00
●
Release −∞–10.00
●
Release Value dB
−∞–
10.00
Normalized
0.00–
1.00
- - - - - OFF:0, ON:1
●
Range Indicator Value Num 0,1