R PDM-1 INPUT INPUT SURROUND VOL VOL N R PICTURE PICTURE PICTURE POS.
Table of Contents Important Safety Notice .............................................. 4 Safety Precautions ...................................................... 5 Accessories ................................................................. 7 Accessories Supply .................................................... 7 Optional Accessories ................................................. 7 Remote Control Batteries ........................................... 8 Connections ...................................
Important Safety Notice WARNING: To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or moisture. Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set. (including on shelves above, etc.) WARNING: 1) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel. 2) Do not remove the earthing pin on the power plug.
Safety Precautions WARNING Setup This plasma display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury. PDS-150 • Pedestal .......................................... .......................... Wall Mounting Unit PWK-150 • .........................................
Safety Precautions If problems occur during use If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odour starts to come out from the plasma display, immediately unplug the power cord plug from the wall outlet. If you continue to use the plasma display in this condition, fire or electric shock could result. After checking that the smoke has stopped, contact your local Yamaha dealer so that the necessary repairs can be made.
Accessories Accessories Supply Check that you have the accessories and items shown Remote Control Transmitter Batteries for the Remote Control Transmitter (2 × R6 Size) Fixing bands 2 pcs AC cord (Australia) Ferrite core (small size) × 1 INPUT SURROUND VOL N R PICTURE SOUND PICTURE POS.
Remote Control Batteries Requires two R6 batteries. 1. Turn the transmitter face down. Press and slide off the battery cover. 2. Install the batteries as shown in the battery compartment. (Polarity + or – must match the markings in the compartment.) 3. Replace the cover and slide in reverse until the lock snaps. Two "R6" size Helpful Hint: For frequent remote control users, replace old batteries with Alkaline batteries for longer life.
Connections AC cord connection (see page 18) – Cable fixing bands Secure any excess cables with bands, as required. To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure. While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band. Pass the attached cable fixing band through the clip as shown in the figure.
Connections Basic connection (Example) When connecting an AV amplifier S VIDEO 4 pin socket AUDIO VIDEO S VIDEO Chrominance earth Luminance in Chrominance in L R L R Luminance earth AUDIO HD VD AV IN PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN Video pin cable S Video cable Component Video cable AV amplifier VOLUME INPUT SELECTOR VIDEO S VIDEO INPUT MODE STANDBY /ON SPEAKERS A B 6CH INPUT PROGRAM STEREO FM/AM PRESET /TUNING A/B/C/D/E PRESET /TUNING EDIT EFFECT BASS BALANCE T
Connections Speaker Terminals connection When you do not use an AV amplifier, connect the speakers directly with the speaker terminals of the plasma display. Refer to the speaker’s Installation Manual for details on speaker installation. When connecting the speakers, be sure to use only the optional accessory speakers. Speakers (Optional accessories) 1 3 2 1 Remove the tubes from the ends of the speaker cables.
Connections Component/RGB Input connection RGB signal (R, G, B, HD, VD) connection BNC-RCA adaptor plug RGB input to R, G, B, HD, VD sockets Example of input signal source HDTV-compatible VCR 5×BNC RGB cables RGB camera R L AUDIO VD HD PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN AUDIO 2×RCA audio cables Audio input to L/R sockets Computer VD HD R B G Notes: (1) Change the “Component/RGB-in” setting in the “Setup” menu to “RGB”.
Connections PC Input Terminals connection COMPUTER AUDIO PC IN POWER / R - STANDBY INPUT — VOL + G POWER ON Conversion adapter (if necessary) Less than 3" 15/16 (10 cm) Ferrite core (large size) (supplied) D-sub 15p RGB PC cable Ferrite core (small size) (supplied) Less than 3" 15/16 (10 cm) Audio 1/8" (3 mm)Stereo plug Connect a cable which matches the audio output terminal on the computer.
Connections Signal Names for D-sub 15P Connector Pin No. 1 2 3 4 5 11 12 13 14 15 6 7 1 9 10 8 2 3 4 5 Pin Layout for PC Input Terminal Signal Name R G B GND (Ground) GND (Ground) Pin No. Signal Name Pin No.
Connections SERIAL Terminals connection The SERIAL terminal is used when the plasma display is controlled by a computer. 6 1 7 2 8 3 9 4 5 Pin layout for RS-232C Notes: (1) Use the RS-232C cable to connect the computer to the plasma display. (2) The computer shown is for example purposes only. (3) Additional equipment and cables shown are not supplied with this set.
Basic Controls INPUT R - STANDBY G POWER ON — VOL + PDM-1 Main Power On/Off Switch Power Indicator The Power Indicator will light. Power-OFF ..... Indicator not illuminated (The unit will still consume some power as long as the power cord is still inserted into the wall outlet.) Stand-by .... Red Power-ON ...... Green • • • INPUT button (AV(S Video), Component/RGB and PC Mode Selection) Press the “INPUT” button to select AV (S Video), Component/RGB and PC input signal modes sequentially.
Basic Controls SURROUND button (see page 27) INPUT button (AV(S Video), Component/RGB and PC Mode Selection) Press to select AV(S Video), Component/RGB and PC input signal modes sequentially. (see page 19) Sound mute On/Off (see page 26) INPUT INPUT SURROUND Volume Adjustment Press the Volume Up “+” or Down “–” button to increase or decrease the sound volume level.
Power On/Off and input signal selection AC cord connection Connecting the AC cord plug to the plasma display. Power On/Off Connecting the plug to the Wall Outlet Note: Main plug types vary between countries. The power plug shown at left may, therefore, not be the type fitted to your set. R - STANDBY INPUT – VOL switch on the plasma display to turn Press the the set on:Power-On.
Power On/Off and input signal selection Select the input signal INPUT Press the INPUT button to select the input AV signal desired from equipment such as a VCR which has been connected to the plasma display. Input signals will change as follows: R - STANDBY INPUT — VOL + For Component Input (see page 34) G POWER ON AV INPUT — Component PC + VOL For RGB Input (see page 34) AV RGB PC INPUT SURROUND VOL N R Selecting the On-Screen Menu Language SET UP Press to display the Setup menu.
On-Screen Menu Display from Remote Control To Picture adjust menu (see page 28) Press to select each item. Picture Normal Normalise Picture Mode Contrast Brightness Colour Tint Sharpness White balance Advanced settings Normal 20 0 0 0 0 INPUT Normal On SURROUND Setup To Advanced Settings (see page 28, 29) VOL RGB Advanced Settings Normal Normalise Black extension W/B High R W/B High B W/B Low R W/B Low B Gamma Component/RGB-in select N English (UK) OSD Language 0 0 0 0 0 Set up TIMER 2.
