User Manual

MONTAGE Data List
214
MIDI Data Table
TOTAL SIZE = 68 44 (HEX)
p = Part number
0 – F
TOTAL SIZE = 39 27 (HEX)
p = Part number
0 – F
TOTAL SIZE = 17 11 (HEX)
p = Part number
0 – F
43 1 00 – 11,
7F
Insertion-B Side Chain Part 0: Part 1, 1: Part 2 –
15: Part 16, 16: A/D,
17: Master, 127: Off
127
Address Size
Data
Range
(HEX)
Parameter Name Description
Default
(HEX)
Notes
31 4p 00 1 00 – 05 LFO Phase 0, 90, 120, 180, 240,
270
00 LFO-related
parameters
hereinafter
are not
available for
Drum Part.
01 1 00 – 0C LFO Wave Triangle, Triangle+,
Saw Up, Saw Down,
Squ1/4, Squ1/3,
Square, Squ2/3,
Squ3/4, Trapezoid,
S/H1, S/H2, User
00
02 1 00 – 3F LFO Speed 0 – 63 20 This is
available
only when
Tempo Sy nc
is set to Off.
03 1 05 – 18 LFO Tempo Speed 5 – 24
(16th, 8th/3, 16th.,
8th, 4th/3, 8th., 4th,
2th/3, 4th., 2nd,
Whole/3, 2nd.,
4thX4, 4thX5, 4thX6,
4thX7, 4thX8,
4thX16, 4thX32,
4thX64)
0B This is
available
only when
Tempo Sy nc
is set to On.
04 1 00 – 01 LFO Tempo Sync Off, On 00
05 1 00 – 7F LFO Delay Time 0 – 127 00
06 1 00 – 7F LFO Fade In Time 0 – 127 00
07 1 00 – 7F LFO Hold Time 0 – 126, Hold 7F
08 1 00 – 7F LFO Fade Out Time 0 – 127 40
09 1 00 – 02 LFO Key On Reset Off, Each-On,1st-On 02
0A 1 00 – 01 LFO Loop Switch On, Off 00
0B 1 00 – 45 LFO Destination 1 0 – 69 (Refer to LFO
Box Destination of
Control List)
02
0C 1 00 – 7F LFO Depth 1 0 – 127 00
0D 1 reserved
0E 1 00 – 45 LFO Destination 2 0 – 69 (Refer to LFO
Box Destination of
Control List)
04
0F 1 00 – 7F LFO Depth 2 0 – 127 00
10 1 reserved
11 1 00 – 45 LFO Destination 3 0 – 69 (Refer to LFO
Box Destination of
Control List)
04
12 1 00 – 7F LFO Depth 3 0 – 127 00
13 1 reserved
14 1 00 – 06 User LFO Cycle 2 steps, 3 steps,
4 steps, 6 steps,
8 steps, 12 steps,
16 steps
06
15 1 00 – 03 User LFO Slope Off, Up, Down,
Up&Down
00
16 1 00 – 7F User LFO Step Value 1 -64 – +63 40
17 1 00 – 7F User LFO Step Value 2 -64 – +63 40
18 1 00 – 7F User LFO Step Value 3 -64 – +63 40
19 1 00 – 7F User LFO Step Value 4 -64 – +63 40
1A 1 00 – 7F User LFO Step Value 5 -64 – +63 40
1B 1 00 – 7F User LFO Step Value 6 -64 – +63 40
1C 1 00 – 7F User LFO Step Value 7 -64 – +63 40
1D 1 00 – 7F User LFO Step Value 8 -64 – +63 40
1E 1 00 – 7F User LFO Step Value 9 -64 – +63 40
1F 1 00 – 7F User LFO Step Value 10 -64 – +63 40
20 1 00 – 7F User LFO Step Value 11 -64 – +63 40
21 1 00 – 7F User LFO Step Value 12 -64 – +63 40
22 1 00 – 7F User LFO Step Value 13 -64 – +63 40
23 1 00 – 7F User LFO Step Value 14 -64 – +63 40
24 1 00 – 7F User LFO Step Value 15 -64 – +63 40
25 1 00 – 7F User LFO Step Value 16 -64 – +63 40
26 1 00 – 7F Part LFO Random Speed
Depth
0 – 127 00 This is
available
only when
Tempo Sy nc
is set to Off.
Address Size
Data
Range
(HEX)
Parameter Name Description
Default
(HEX)
Notes Address Size
Data
Range
(HEX)
Parameter Name Description
Default
(HEX)
Notes
31 5p 00 1 00 – 01 Zone Switch Off, On 00
01 1 00 – 0F,
7F
MIDI Transmit Channel Ch1 – 16, Off 7F
02 1 3D – 43 Zone Octave Shift -3 – +3 40
03 1 35 – 4B Zone Transpose -11 – +11 (semitones) 40
04 1 00 – 7F Note Limit Low C-2 – G8 00
05 1 00 – 7F Note Limit High C-2 – G8 7F
06 1 00 – 01 Zone Internal Switch Off, On 01
07 1 00 – 7F MIDI Volume 0 – 127 64
08 1 00 – 7F MIDI Pan L64 – C – R63 40
09 1 00 – 7F MIDI Bank MSB 0 – 127 00
0A 1 00 – 7F MIDI Bank LSB 0 – 127 00
0B 1 00 – 7F MIDI Program Number 1 – 128 00
0C 1 00 – 7F Transmit Pitch Bend
Transmit After Touch
Transmit Program Change
Transmit Bank Select
Transmit Control Change
bit 6: Off, On PB
bit 5: Off, On AT
bit 4: Off, On Program
Change
bit 3: Off, On Bank Select
bit 2: Off, On Control
Change
bit1-0: reserved
7C
0D 1 00 – 7F Transmit Assignable Knob 8
Transmit Assignable Knob 7
Transmit Assignable Knob 6
Transmit Assignable Knob 5
Transmit Assignable Knob 4
Transmit Assignable Knob 3
Transmit Assignable Knob 2
bit 6: Off, On Assignable
Knob 8
bit 5: Off, On Assignable
Knob 7
bit 4: Off, On Assignable
Knob 6
bit 3: Off, On Assignable
Knob 5
bit 2: Off, On Assignable
Knob 4
bit 1: Off, On Assignable
Knob 3
bit 0: Off, On Assignable
Knob 2
7F
0E 1 00 – 7F Transmit Assignable Knob 1
Transmit Foot Controller 2
Transmit Foot Controller1
Transmit Modulation Wheel
Transmit Sustain/Sostenuto
Trans mit Pa n
Transmit Volume/Expression
bit 6: Off, On Assignable
Knob 1
bit 5: Off, On FC2
bit 4: Off, On FC1
bit 3: Off, On MW
bit 2: Off, On Sustain/
Sostenute
bit 1: Off, On Pan
bit 0: Off, On Volume/
Expression
7F
0F 1 00 – 7F Transmit Ribbon Controller
Transmit Breath Controller
Transmit Foot Switch
bit 6: Off, On RB
bit 5: Off, On BC
bit 4: Off, On FS
bit 3: reserved
bit 2: reserved
bit 1: reserved
bit 0: reserved
70
10 1 00 – 7F Transmit Motion Seq Trigger
Transmit Motion Seq Hold
Trans mit As signa bl e
Function 2
Trans mit As signa bl e
Function 1
bit 6: Off, On Motion Seq
Trigger
bit 5: Off, On Motion Seq
Hold
bit 4: Off, On Assignable
Function 2
bit 3: Off, On Assignable
Function 1
bit 2: reserved
bit 1: reserved
bit 0: reserved
78
Address Size
Data
Range
(HEX)
Parameter Name Description
Default
(HEX)
Notes
31 6p 00 1 00 – 01 Part Arp Switch Off, On 00
01 1 reserved
02 1 reserved
03 1 00 – 01 Arp Play Only Off, On 00
04 1 00 – 01 Arp Fixed SD/BD Off, On 00
Not
available
for
Normal/
FM Parts
05 1 reserved
06 1 00 – 01 Arp Loop Off, On 01
07 1 00 – 02 Arp Hold Sync-Off, Off, On 01
08 1 00 – 0A Part Unit Multiply 50%, 66%, 75%, 100%,
133%, 150%, 200%,
266%, 300%, 400%,
Common
03
09 1 00 – 7F Arp Note Limit Low C-2 – G8 00
0A 1 00 – 7F Arp Note Limit High C-2 – G8 7F
0B 1 01 – 7F Arp Velocity Limit Low 1 – 127 01
0C 1 01 – 7F Arp Velocity Limit High 1 – 127 7F
0D 1 00 – 04 Arp Key Mode Sort, Thru, Direct,
Sort+Drct, Thru+Drct
00
0E 1 00 – 01 Arp Velocity Mode Original, Thru 00
0F 1 00 – 01 Arp Change Timing Real-time, Measure 01
10 1 01 – 07 Arp / Motion Seq Gird 60, 80, 120, 160, 240,
320, 480
03
11 1 00 – 64 Arp Quantize Strength 0 – 100% 00