User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon and channel color
- Making HA (Head Amp) settings
- Sending a signal from an input channel to the STEREO/MONO buses
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Correcting delay between channels (Input Delay)
- Channel library operations
- Output channels
- EQ and Dynamics
- Grouping and linking
- Scene memory
- About scene memories
- Using scene memories
- Editing scene memories
- Using the Global Paste function
- Using the Focus function
- Using the Recall Safe function
- Using the Fade function
- Outputting a control signal to an external device in tandem with scene recall (GPI OUT)
- Playing back an audio file that links to a scene recall
- Using Preview mode
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, effects, and Premium Rack
- I/O device and external head amp
- MIDI
- User settings (Security)
- Recorder
- Help function
- Other functions
- About the SETUP screen
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Appendices
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Effects and tempo synchronization
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- Functions that can be assigned to USER DEFINED keys
- Functions that can be assigned to USER DEFINED knobs
- Functions that can be assigned to the assignable encoders
- MIDI Data Format
- Warning/Error Messages
- Electrical characteristics
- Mixer Basic Parameters
- M IDI Implementation Chart
- Index
Recorder
Reference Manual
191
■ When setup method selection button = SPECIFIED IP ADDRESS
If you’re using DANTE-ACCEL, use the SPECIFIED IP ADDRESS field to specify the IP address of the
PC. Since the IP address of DANTE-ACCEL will differ from the IP address used by CL Extension, you
must specify the IP address manually.
This screen contains the following items.
1 IP ADDRESS knobs
Use the multifunction knobs to specify the IP address.
NOTE
• As the IP address, specify the IP address of the PC that is running Nuendo Live.
• Set the address of that PC in the range of 169.254.0.0 – 169.254.255.255, and set the subnet
mask as 255.255.0.0.
• For the PC in which DANTE-ACCEL is installed, the Dante port of DANTE-ACCEL as well as the
Ethernet port of the PC must both be connected to the same network.
Refer to the illustration below.
NOTE
Depending on the firmware version, DANTE-ACCEL might not support redundant networking.
Refer to the following website to check whether your version of the DANTE-ACCEL (Dante
Accelerator) firmware supports redundant networking.
http://www.yamahaproaudio.com/
2. When you have finished making settings, press the OK button to close the
NUENDO LIVE SET UP popup window.
1
PC
SW
(Primary)
SW
(Secondary)
Ethernet
DANTE-ACCEL
P
S
CL
Dante
P
S