Owner`s manual

ManualsBrandsYamaha ManualsStereo ReceiverHTR-5440

3

4

5

6

7

8

9

OYAMAHAe

YHT-24

QUICK-CONNECT

GUIDE

OPERATING

THE

UNIVERSAL

REMOTE

CONTROL

3.

Load a DVD (or

LD)

into the DVD (or

LD)

player.

4.

Aim

the remote control at the DVD (or

LD)

player,

and

press>

(forward button) to start play.

NOTE:

The

DVD player's

controls

are

now

assigned

to

the

remote

control

buttons,

since

DVD

was

the

last

selected

component.

3.

Using the

keypad,

enter

the code "0000".

4.

The indicator LED will flash twice to confirm all

codes have been reset to factory values.

If

the

lED

does

not

flash twice,

repeat

steps 1

through

3.

5.

For

your

convenience, the following reference

chart

lists the factory codes:

Component

Component

Code

Selector Button

RESETTING

THE

REMOTE

CONTROL

To

fACTORY

CODES

You can reset the remote control to factory codes for all

components

or

a

desired

component, as follows:

RESETTING

CODES

FOR

ALL

COMPONENTS

1. Press any

component

selector

button

other

than

AMP/TUNER.

2.

Press

and

hold

both

VOLUME

buttons

at least four

seconds until the indicator

LED

flashes twice.

3.

Using the keypad,

enter

the

code

"9990".

4.

The indicator LED will flash twice to confirm all

codes have been reset to factory values.

If

the

lED

does

not

flash twice,

repeat

steps 1

through

3.

RESETTING

CODES

FOR

A

DESIRED

COMPONENT

1.

Press a

component

selector

button

that

matches the

component

you

wish

to reset to factory codes.

2.

Press

and

hold

both

VOLUME

buttons

at

least four

seconds until the indicator LED flashes twice.

0101

0006

0002

0008 Yamaha

0005 Yamaha

0024 Yamaha

TV

Cable

TV

VCR

DVD

player

CD

player

MD recorder

TV

CBL/SAT

VCR

DVD/LD

CD

TAPE/MD

PLAYING

ADVD

1.

Aim

the remote control at the HTR-5440, press AMP/

TUNER to select the component,

and

then press

POWER to

turn

the receiver on. Press DVD

/lD

(i.e.,

4

on the keypad) as the input for the receiver.

2.

Press DVD

/lD

and

then

press POWER to

turn

the

DVD (or

lD)

player on.

NOTE:

If

the

DVD

player

is

plugged

into

the

switched

ac

outlet

(on

the

back

of

the

receiver)

and

its

power

switch

was

already

engaged,

the

unit will

come

on

each

time

the

receiver

is

powered

on.

OVERVIEW

The universal remote control will control

up

to seven

different types of components (including the HTR-5440

receiver), each of which becomes active

when

you

press

a selection (e.g.,

TV,

VCR,

etc.). We can only briefly

describe some functions here,

and

we

encourage you

use the

HTR-5440 Owner's

Manual

to gain additional

experience

with

this powerful unit.

PLAYING

A

VIDEOCASSETTE

1.

Aim the remote control at the HTR-5440, press

AMP

/TUNER

to select the component,

and

then

press POWER to

turn

the receiver on. Press

VCR

(i.e.,

6

on

the keypad) as the

input

for the receiver.

2.

Aim

the remote control

at

the

TV,

press the

TV

to

select the component,

and

then press POWER to

turn

the television on. Press

TV

INPUT (or

A/B)

to

select the correct input.

3.

Aim the remote control at the

VCR,

press

VCR

to

select the component,

and

then press POWER to

turn

the

VCR

on.

Put

a tape in the

VCR,

press PLAY.

NOTE:

At

this

point,

the

VCR

controls

are

assigned

to

the

remote

control,

since

VCR

was

the

last

selected

compo-

nent. If

you

now

press

the

VOLUME

up

(down)

buttons,

the

TV

NCR

volume

will

be

raised

(or

lowered).

To

adjust

the

receiver's

volume,

you

must

press

AMP/TUNER

to

activate

its

functions.

_YAMAHA-

©2001

YAMAHA ELECTRONICS CORPORA

nON,

USA

6660

Orange

thorpe

Avenue, Buena Park, CA 90620

PH: (714) 522-9105;

FAX:

(888) 435-7922

http://www.yamaha.com