Read this manual carefully before operating this vehicle.
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM EAU10042 Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM INTRODUCTION EAU10083 Congratulations on your purchase of the Yamaha FJR13AD(C). This model is the result of Yamaha’s vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields. This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle.
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM IMPORTANT MANUAL INFORMATION EAU10133 Particularly important information is distinguished in this manual by the following notations: This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING NOTICE TIP A WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
U1MC10E0.book Page 2 Monday, July 30, 2012 4:56 PM IMPORTANT MANUAL INFORMATION EAU10193 FJR13AD(C) OWNER’S MANUAL ©2012 by Yamaha Motor Corporation, U.S.A. 1st edition, July 2012 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A. is expressly prohibited. Printed in Japan.
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM TABLE OF CONTENTS LOCATION OF IMPORTANT LABELS .............................................1-1 SAFETY INFORMATION ..................2-1 DESCRIPTION ..................................3-1 Left view ..........................................3-1 Right view ........................................3-2 Controls and instruments.................3-3 INSTRUMENT AND CONTROL FUNCTIONS .......................................4-1 Main switch/steering lock ...............
U1MC10E0.book Page 2 Monday, July 30, 2012 4:56 PM TABLE OF CONTENTS Checking and lubricating the brake and shift pedals ...............7-28 Checking and lubricating the brake and clutch levers .............7-29 Checking and lubricating the centerstand and sidestand ........7-29 Lubricating the rear suspension ...7-30 Lubricating the swingarm pivots ...7-30 Checking the front fork .................7-31 Checking the steering ...................7-31 Checking the wheel bearings .......7-32 Battery ...........
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM LOCATION OF IMPORTANT LABELS EAU10384 1 Read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label is available from your Yamaha dealer.
U1MC10E0.book Page 2 Monday, July 30, 2012 4:56 PM LOCATION OF IMPORTANT LABELS 1 California only 3 LOAD LIMIT FUEL TANK 3 kg {7 lbs} ATMOSPHERE 3TB-24877-A0 #1 #2 #3 #4 EMISSION HOSE ROUTING CHARCOAL THROTTLE BODY CANISTER 1MC-21686-00 2 California only 4 LOAD LIMIT VACUUM HOSE ROUTING 1 kg {2 lbs} PRESS.
U1MC10E0.book Page 3 Monday, July 30, 2012 4:56 PM LOCATION OF IMPORTANT LABELS 5 8 6 9 1 250 kPa, {2.50 kgf/cm 2 }, 36 psi 290 kPa, {2.90 kgf/cm 2 }, 42 psi 7 250 kPa, {2.50 kgf/cm 2 }, 36 psi 290 kPa, {2.90 kgf/cm 2 }, 42 psi NOTICE 5VY-21668-00 Cleaning with alkaline or acid cleaner, gasoline or solvent will damage windshield. Use neutral detergent.
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM SAFETY INFORMATION EAU1028A Be a Responsible Owner As the vehicle’s owner, you are responsible for the safe and proper operation of your motorcycle. Motorcycles are single-track vehicles. Their safe use and operation are dependent upon the use of proper riding techniques as well as the expertise of the operator. Every operator should know the following requirements before riding this motorcycle.
U1MC10E0.book Page 2 Monday, July 30, 2012 4:56 PM SAFETY INFORMATION ● 2 ● Many accidents involve inexperienced operators. In fact, many operators who have been involved in accidents do not even have a current motorcycle license. • Make sure that you are qualified and that you only lend your motorcycle to other qualified operators. • Know your skills and limits. Staying within your limits may help you to avoid an accident.
U1MC10E0.book Page 3 Monday, July 30, 2012 4:56 PM SAFETY INFORMATION Avoid Carbon Monoxide Poisoning All engine exhaust contains carbon monoxide, a deadly gas. Breathing carbon monoxide can cause headaches, dizziness, drowsiness, nausea, confusion, and eventually death. Carbon Monoxide is a colorless, odorless, tasteless gas which may be present even if you do not see or smell any engine exhaust.
U1MC10E0.book Page 4 Monday, July 30, 2012 4:56 PM SAFETY INFORMATION ● 2 tents, can create unstable handling or a slow steering response. This vehicle is not designed to pull a trailer or to be attached to a sidecar. Genuine Yamaha Accessories Choosing accessories for your vehicle is an important decision. Genuine Yamaha accessories, which are available only from a Yamaha dealer, have been designed, tested, and approved by Yamaha for use on your vehicle.
U1MC10E0.book Page 5 Monday, July 30, 2012 4:56 PM SAFETY INFORMATION ● tor and may limit control ability, therefore, such accessories are not recommended. Use caution when adding electrical accessories. If electrical accessories exceed the capacity of the motorcycle’s electrical system, an electric failure could result, which could cause a dangerous loss of lights or engine power.
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM DESCRIPTION EAU10410 Left view 1 2 3 4 3 13 12 11 10 9 8 7 1. 2. 3. 4. 5. 6. 7. 8. 6 5 9. Shift pedal (page 4-23) 10.Engine oil filler cap (page 7-13) 11.Engine oil filter cartridge (page 7-13) 12.Engine oil level check window (page 7-13) 13.
U1MC10E0.book Page 2 Monday, July 30, 2012 4:56 PM DESCRIPTION EAU10420 Right view 1 2 3,4 5 6,7 3 11 10 1. 2. 3. 4. 5. 6. 7. 8. 9 8 9. Brake pedal (page 4-24) 10.Shock absorber assembly rebound damping force adjusting knob (page 4-40) 11.
U1MC10E0.book Page 3 Monday, July 30, 2012 4:56 PM DESCRIPTION EAU10430 Controls and instruments 1 2 3 4 5 6 7 8 2 3 11 1. 2. 3. 4. 5. 6. 7. 8. 12 10,11 9. Brake lever (page 4-24) 10.Throttle grip (page 7-20) 11.Grip warmer (page 4-10) 12.
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS EAU10461 Main switch/steering lock EAU10661 OFF All electrical systems are off. The key can be removed. To lock the steering 1 2 EWA10061 WARNING Never turn the key to “OFF” or “LOCK” while the vehicle is moving. Otherwise the electrical systems will be switched off, which may result in loss of control or an accident.
U1MC10E0.book Page 2 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS To unlock the steering 1 ECA11020 NOTICE 2 Do not use the parking position for an extended length of time, otherwise the battery may discharge. EAU49392 Indicator lights and warning lights 1 23 4 5 6 7 GEAR N A.TEMP C.TEMP TIME TRIP 4 1. Push. 2. Turn. ˚F 77 Lo 0:06 ˚F 9 8 1. 2. 3. 4. 5. 6.
U1MC10E0.book Page 3 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS EAU11060 Neutral indicator light “ ” This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light “ ” This indicator light comes on when the high beam of the headlight is switched on. EAU11123 Oil level warning light “ ” This warning light comes on if the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”.
U1MC10E0.book Page 4 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS while riding, the brake system reverts to conventional braking. If either of the above occurs, or if the warning light does not come on at all, use extra caution to avoid possible wheel lock during emergency braking. Have a Yamaha dealer check the brake system and electrical circuits as soon as possible.
U1MC10E0.book Page 5 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS N A.TEMP C.TEMP TIME TR 1 2 1. Cruise control system indicator light “ ” 2. Cruise control setting indicator light “SET” Activating and setting the cruise control system 1. Push the cruise control power switch “ ” located on the left handlebar. The cruise control system indicator light “ ” will come on. 2. Push the “SET–” side of the cruise control setting switch to activate the cruise control system.
U1MC10E0.book Page 6 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS speed will return to the previously set cruising speed. The “SET” indicator light will come on. EWA16350 2 WARNING 1 It is dangerous to use the resume function when the previously set cruising speed is too high for current conditions. 4 1. Closed position 2. Cruise control cancel direction ● Apply the front or rear brake. ● Disengage the clutch. Push the power switch to turn off the cruise control system.
U1MC10E0.book Page 7 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS If the cruise control system is automatically deactivated, please stop and confirm that your vehicle is in good operating condition. Before using the cruise control system again, activate it using the power switch. TIP In some cases, the cruise control system may not be able to maintain the set cruising speed when the vehicle is traveling uphill or downhill.
U1MC10E0.book Page 8 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS EAU54781 Multi-function meter unit 12 3 4 5 6 7 8 9 10 11 GEAR N A.TEMP C.TEMP TIME TRIP ˚F 77 Lo 0:06 ˚F settings while riding can distract the operator and increase the risk of an accident. ● TIP The select switch “ / ” and the menu switch “MENU” are located on the left handlebar. These switches allow you to control or change the settings of the multi-function meter unit. ● ● ● 4 1. “RESET” button 2.
U1MC10E0.book Page 9 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS Tachometer 1 segments start flashing. If this occurs, have a Yamaha dealer check the electrical circuit. Fuel meter 1 2 Eco indicator 1 GEAR N A.TEMP C.TEMP 1. Tachometer 2. Tachometer red zone 4 1. Fuel meter The electric tachometer allows the rider to monitor the engine speed and keep it within the ideal power range.
U1MC10E0.book Page 10 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS ● Select the transmission gear that is appropriate for the vehicle speed. Function display Drive mode display 1 1 Transmission gear display 1 GEAR N 2 A.TEMP GEAR N C.TEMP TIME TRIP A.TEMP GEAR 4 C.TEMP N A.TEMP C.TEMP TIME TRIP 2 ˚F 77 Lo 0:06 1. Drive mode display ˚F 1. Neutral indicator light “ ” 2.
U1MC10E0.book Page 11 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS ● Adjusting the grip warmer This vehicle is equipped with grip warmers, which can only be used when the engine is running. There are 4 grip warmer settings. If the handlebar grip or throttle grip becomes worn or damaged, stop using the grip warmers and replace the grips. Selecting the information display Setting Display GEAR TRIP-1 1 Low 2 GEAR A.TEMP C.
U1MC10E0.book Page 12 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS “TRIP-1” and “TRIP-2” show the distance traveled since they were last set to zero. 4 When approximately 5.5 L (1.45 US gal, 1.21 Imp.gal) of fuel remains in the fuel tank, the last segment of the fuel meter starts flashing. In addition, the information display will automatically change to the fuel reserve tripmeter mode “TRIP-F” and start counting the distance traveled from that point.
U1MC10E0.book Page 13 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS ● TIP ● ● ● 16 °F will be displayed even if the ambient temperature falls below 16 °F. 122 °F will be displayed even if the ambient temperature climbs above 122 °F. The accuracy of the temperature reading may be affected when riding slowly [approximately under 20 km/h (12.5 mi/h)] or when stopped at traffic signals, railroad crossings, etc. GEAR 4 C.
U1MC10E0.book Page 14 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS ECA15473 NOTICE If there is a malfunction, “– –.–” will be continuously displayed. Have a Yamaha dealer check the vehicle. Instantaneous fuel consumption display: FUEL CRNT 4 TIP If traveling at speeds under 10 km/h (6.2 mi/h), “_ _._” will be displayed. The instantaneous fuel consumption display modes “km/L”, “L/100km” or “MPG” show the fuel consumption under the current riding conditions.
U1MC10E0.book Page 15 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS “Unit” “Display” “Brightness” “Clock” “All Reset” This function allows you to switch the display units between kilometers and miles. When kilometers are selected, the fuel consumption units can be switched between “L/100km” and “km/L”. This function allows you to change the items shown in 3 information displays.
U1MC10E0.book Page 16 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS 2. Push the menu switch “MENU”, and then push the “RESET” button to select the item to reset. Grip Warmer High 10 Maintenance Middle 5 OIL mile 1 FREE-1 mile FREE-2 mile 12 Low 6 4 TIP The setting can be set to 10 temperature levels. Resetting the maintenance counters 1. Use the select switch to highlight “Maintenance”. MENU Grip Warmer Maintenance Time Trip Unit Display Brightness Clock 6 3.
U1MC10E0.book Page 17 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS 4. Push the menu switch “MENU” to return to the setting mode menu. Selecting the units 1. Use the select switch to highlight “Unit”. MENU 3. Push the menu switch “MENU”. “km” or “mile” will flash in the display. 4. Use the select switch to select “km” or “mile”, and then push the menu switch “MENU”. Unit Grip Warmer Maintenance Time Trip Unit Display Brightness Clock 6.
U1MC10E0.book Page 18 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS MENU Grip Warmer Maintenance Time Trip Unit Display Brightness Clock 4 2. Push the menu switch “MENU”, use the select switch to highlight the display to change, and then push the menu switch “MENU” again. Display-1 Display-1 1-1 1-1 A.TEMP 1-2 C.TEMP 1-3 TIME TRIP TIME TRIP 4. Use the select switch to select the item to show, and then push the menu switch “MENU”. 6.
U1MC10E0.book Page 19 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS 3. Use the select switch to select the desired brightness level, and then push the menu switch “MENU” to return to the setting mode menu. 3. When the hour digits start flashing, use the select switch to set the hours. Clock Brightness 5 55 Setting the clock 1. Use the select switch to highlight “Clock”. 4. Push the menu switch “MENU”, and the minute digits start flashing. 5. Use the select switch to set the minutes.
U1MC10E0.book Page 20 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS Self-diagnosis device ECA11590 GEAR N A.TEMP C.TEMP TIME TRIP 4 1 ˚C 25 Lo 0:06 ˚C D-mode (drive mode) If the display indicates an error code, the vehicle should be checked as soon as possible in order to avoid engine damage. D-mode is an electronically controlled engine performance system with two mode selections (touring mode “T” and sports mode “S”). Push the drive mode switch “MODE” to switch between modes.
U1MC10E0.book Page 21 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS This mode allows the rider to enjoy smooth drivability from the low-speed range to the high-speed range. EAU1234B Handlebar switches Right 1 Left STO Sports mode “S” This mode offers a sportier engine response in the low- to mid-speed range compared to the touring mode.
U1MC10E0.book Page 22 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS position. To cancel the turn signal lights, push the switch in after it has returned to the center position. EAU12500 Horn switch “ ” Press this switch to sound the horn. EAU54210 4 Start/Engine stop switch “ / / ” To crank the engine with the starter, set this switch to “ ”, and then push the “ ” side of the switch. See page 6-1 for starting instructions prior to starting the engine.
U1MC10E0.book Page 23 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS EAU12830 Clutch lever 3 2 1 5 4 1 2 3 4 Make sure that the appropriate setting on the adjusting dial is aligned with the arrow mark on the clutch lever. The clutch lever is equipped with a clutch switch, which is part of the ignition circuit cut-off system. (See page 4-42.) EAU12871 Shift pedal 4 1. 2. 3. 4.
U1MC10E0.book Page 24 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS EAU26824 Brake lever EAU39540 Brake pedal The brake lever is located on the right side of the handlebar. To apply the front brake, pull the lever toward the throttle grip. 1 1 2 2 4 3 4 1. 2. 3. 4. 1 5 4 3 Brake lever Brake lever position adjusting dial “ ” mark Distance between brake lever and throttle grip The brake lever is equipped with a brake lever position adjusting dial.
U1MC10E0.book Page 25 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS TIP ● ● The ABS performs a self-diagnosis test each time the vehicle first starts off after the key is turned to “ON” and the vehicle has traveled at a speed of 10 km/h (6 mi/h) or higher. During this test, a “clicking” noise can be heard from under the seat, and if the brake lever or brake pedal is even slightly applied, a vibration can be felt at the lever and pedal, but these do not indicate a malfunction.
U1MC10E0.book Page 26 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS proach surfaces that may be slippery with caution and avoid especially slippery surfaces. 4 When the key is turned to “ON”, the traction control system automatically turns on. The traction control system can be turned on or off manually only when the key is in the “ON” position and the motorcycle is stopped.
U1MC10E0.book Page 27 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS To reset the traction control system Turn the key to “OFF”. Wait at least 1 second, then turn the key back to “ON”. The “TCS” indicator/warning light should go off and the system will be enabled. The engine trouble warning light should go off after the motorcycle reaches at least 20 km/h (12 mi/h).
U1MC10E0.book Page 28 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS ately. If gasoline spills on your skin, wash with soap and water. If gasoline spills on your clothing, change your clothes. EAU13221 Fuel Make sure there is sufficient gasoline in the tank. EWA10881 WARNING 4 Gasoline and gasoline vapors are extremely flammable. To avoid fires and explosions and to reduce the risk of injury when refueling, follow these instructions. 1.
U1MC10E0.book Page 29 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS or premium unleaded fuel. Use of unleaded fuel will extend spark plug life and reduce maintenance costs. Gasohol There are two types of gasohol: gasohol containing ethanol and that containing methanol. Gasohol containing ethanol can be used if the ethanol content does not exceed 10% (E10).
U1MC10E0.book Page 30 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS EAU13445 NOTICE This vehicle is equipped with catalytic converters in the exhaust system. Use only unleaded gasoline. The use of leaded gasoline will cause unrepairable damage to the catalytic converter. EWA10862 WARNING 4 ECA10701 Catalytic converters The exhaust system is hot after operation.
U1MC10E0.book Page 31 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS 2. Install the passenger seat. TIP ● ● 1. Projection 2. Seat holder 2. Remove the key. Rider seat To remove the rider seat 1. Remove the passenger seat. 2. Push the rider seat lock lever, located under the back of the rider seat, to the left as shown, and then pull the seat off. 1. Rider seat lock lever 2. Rider seat To install the rider seat 1.
U1MC10E0.book Page 32 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS EAU39632 Adjusting the rider seat height The rider seat height can be adjusted to one of two positions to suit the rider’s preference. The rider seat height was adjusted to the lower position at delivery. 1. Rider seat height position adjuster 4 3. Move the rider seat holder cover to the lower position as shown. 1. Rider seat height position adjuster 2. “H” mark 3. Match mark 5.
U1MC10E0.book Page 33 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS 6. Align the projection on the bottom of the rider seat with the “L” position slot, and then push the rear of the seat down to lock it in place as shown. 6. Align the projection on the bottom of the rider seat with the “H” position slot, and then push the rear of the seat down to lock it in place as shown. 1. Rider seat height position adjuster 2. “L” mark 3. Match mark 1. “H” position slot 5.
U1MC10E0.book Page 34 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS ● EAU40252 Storage compartments This vehicle is equipped with two storage compartments. Storage compartment A is located under the rider seat. (See page 4-30.) 1 1 1. Storage compartment B 4 1. Storage compartment A Storage compartment B is located under the passenger seat. (See page 4-30.
U1MC10E0.book Page 35 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS EAU39480 Accessory box 2. Remove the key. EAU39611 ECA11800 The accessory box is located beside the meter panel. To open the accessory box 1. Insert the key into the main switch, and then turn it to “ON”. 2. Push the accessory box button, and then open the accessory box lid. 2 NOTICE Do not place heat-sensitive items in the accessory box.
U1MC10E0.book Page 36 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS EAU39641 Handlebar position The handlebars can be adjusted to one of three positions to suit the rider’s preference. Have a Yamaha dealer adjust the position of the handlebars. EAU54150 Opening and closing the cowling vents 2 The cowling vents can be opened 20 mm (0.79 in) for added ventilation to suit the riding conditions. 1 3 1 4 1 1. Handlebar 2 1 1. Cowling vent panel 2. Lower slot 3. Quick fastener 3.
U1MC10E0.book Page 37 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS 4. Install the quick fastener. EAU39671 2 To close a cowling vent 1. Remove the quick fastener. 2. Slide the cowling vent panel forward to unhook its projections from the upper slots, and then pull the panel off. 2 1 The rear view mirrors of this vehicle can be folded forward or backward for parking in narrow spaces. Fold the mirrors back to their original position before riding. 3 1 2 1 1 2 1. Projection 2.
U1MC10E0.book Page 38 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS EAU54140 Adjusting the front fork EWA14670 1 WARNING Always adjust the spring preload on both fork legs equally, otherwise poor handling and loss of stability may result. 4 Each front fork leg is equipped with a spring preload adjusting bolt. The right front fork leg is equipped with a rebound damping force adjusting knob and compression damping force adjusting screw.
U1MC10E0.book Page 39 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS ber of clicks of each damping force adjusting mechanism and to modify the specifications as necessary. Rebound damping setting: Minimum (soft): 16 click(s) in direction (b)* Standard: 12 click(s) in direction (b)* Maximum (hard): 1 click(s) in direction (b)* * With the adjusting knob fully turned in direction (a) Compression damping force The compression damping force is adjusted on the right front fork leg only.
U1MC10E0.book Page 40 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS EAU14916 Adjusting the shock absorber assembly This shock absorber assembly is equipped with a spring preload adjusting lever and a rebound damping force adjusting knob. (a) (b) ECA16570 NOTICE 4 To avoid damaging the mechanism, do not attempt to move beyond the maximum or minimum settings. Spring preload For riding solo, move the spring preload adjusting lever in direction (a).
U1MC10E0.book Page 41 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS EWA10221 WARNING This shock absorber assembly contains highly pressurized nitrogen gas. Read and understand the following information before handling the shock absorber assembly. ● Do not tamper with or attempt to open the cylinder assembly. ● Do not subject the shock absorber assembly to an open flame or other high heat source. This may cause the unit to explode due to excessive gas pressure.
U1MC10E0.book Page 42 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS EAU54490 Ignition circuit cut-off system 4 The ignition circuit cut-off system (comprising the sidestand switch, clutch switch and neutral switch) has the following functions. ● It prevents starting when the transmission is in gear and the sidestand is up, but the clutch lever is not pulled. ● It prevents starting when the transmission is in gear and the clutch lever is pulled, but the sidestand is still down.
U1MC10E0.book Page 43 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS With the engine turned off: 1. Move the sidestand down. 2. Make sure that the start/engine stop switch is set to “ 3. Turn the key on. 4. Shift the transmission into the neutral position. 5. Push the “ ” side of the start/engine stop switch. Does the engine start? YES WARNING • The vehicle must be placed on the center- ”. stand during this inspection.
U1MC10E0.book Page 44 Monday, July 30, 2012 4:56 PM INSTRUMENT AND CONTROL FUNCTIONS EAU39655 Auxiliary DC jack 1 EWA14360 WARNING To prevent electrical shock or shortcircuiting, make sure that the cap is installed when the auxiliary DC jack is not being used. ECA15431 NOTICE 4 The accessory connected to the auxiliary DC jack should not be used with the engine turned off, and the load must never exceed 30 W (2.5 A), otherwise the fuse may blow or the battery may discharge. 1.
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM FOR YOUR SAFETY – PRE-OPERATION CHECKS EAU15596 Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection and maintenance procedures and schedules described in the Owner’s Manual. EWA11151 WARNING Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment damage. Do not operate the vehicle if you find any problem.
U1MC10E0.book Page 2 Monday, July 30, 2012 4:56 PM FOR YOUR SAFETY – PRE-OPERATION CHECKS ITEM 5 CHECKS PAGE Rear brake • • • • • • • Check operation. If soft or spongy, have Yamaha dealer bleed hydraulic system. Check brake pads for wear. Replace if necessary. Check fluid level in reservoir. If necessary, add specified brake fluid to specified level. Check hydraulic system for leakage. 7-25, 7-26 Clutch • • • • • Check operation. If soft or spongy, have Yamaha dealer bleed hydraulic system.
U1MC10E0.book Page 3 Monday, July 30, 2012 4:56 PM FOR YOUR SAFETY – PRE-OPERATION CHECKS ITEM CHECKS Instruments, lights, signals and switches • Check operation. • Correct if necessary. Sidestand switch • Check operation of ignition circuit cut-off system. • If system is not working correctly, have Yamaha dealer check vehicle.
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM OPERATION AND IMPORTANT RIDING POINTS EAU15951 EAU47150 EAU54750 Starting the engine Read the Owner’s Manual carefully to become familiar with all controls. If there is a control or function you do not understand, ask your Yamaha dealer. EWA10271 WARNING Failure to familiarize yourself with the controls can lead to loss of control, which could cause an accident or injury.
U1MC10E0.book Page 2 Monday, July 30, 2012 4:56 PM OPERATION AND IMPORTANT RIDING POINTS dicator light remains on, see page 4-2 for the corresponding warning and indicator light circuit check. battery. Do not crank the engine more than 10 seconds on any one attempt. EAU16671 Shifting ECA11042 The ABS warning light should come on when the key is turned to “ON”, and then go off after traveling at a speed of 10 km/h (6 mi/h) or higher.
U1MC10E0.book Page 3 Monday, July 30, 2012 4:56 PM OPERATION AND IMPORTANT RIDING POINTS ECA10260 NOTICE ● ● 6 Even with the transmission in the neutral position, do not coast for long periods of time with the engine off, and do not tow the motorcycle for long distances. The transmission is properly lubricated only when the engine is running. Inadequate lubrication may damage the transmission.
U1MC10E0.book Page 4 Monday, July 30, 2012 4:56 PM OPERATION AND IMPORTANT RIDING POINTS EAU16841 Engine break-in There is never a more important period in the life of your engine than the period between 0 and 1600 km (1000 mi). For this reason, you should read the following material carefully. Since the engine is brand new, do not put an excessive load on it for the first 1600 km (1000 mi). The various parts in the engine wear and polish themselves to the correct operating clearances.
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU17244 EWA15122 EAU17302 WARNING 7 Periodic inspection, adjustment, and lubrication will keep your vehicle in the safest and most efficient condition possible. Safety is an obligation of the vehicle owner/operator. The most important points of vehicle inspection, adjustment, and lubrication are explained on the following pages.
U1MC10E0.book Page 2 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU17361 Owner’s tool kit 1. Owner’s tool kit The owner’s tool kit is located under the rider seat. (See page 4-30.) The service information included in this manual and the tools provided in the owner’s tool kit are intended to assist you in the performance of preventive maintenance and minor repairs. However, additional tools such as a torque wrench may be necessary to perform certain maintenance work correctly.
U1MC10E0.book Page 3 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU48490 TIP ● ● From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months. Items marked with an asterisk require special tools, data and technical skills, have a Yamaha dealer perform the service. EAU17601 Periodic maintenance chart for the emission control system INITIAL No.
U1MC10E0.book Page 4 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL No. ITEM ROUTINE 7 * Evaporative emission control system (for California only) • Check control system for damage. • Replace if necessary. 8 * Air induction system • Check the air cut-off valve, reed valve, and hose for damage. • Replace any damaged parts.
U1MC10E0.book Page 5 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU32188 General maintenance and lubrication chart INITIAL No. ITEM ROUTINE 1 Air filter element • Clean with compressed air. • Replace if necessary. 2 * Clutch • Check operation and fluid leakage. • Correct if necessary.
U1MC10E0.book Page 6 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL No. ITEM ROUTINE 9 * Wheel bearings • Check bearings for smooth operation. • Replace if necessary. 10 * Swingarm pivot bearings • Check bearing assemblies for looseness. • Moderately repack with lithiumsoap-based grease. 11 * Steering bearings • Check bearing assemblies for looseness.
U1MC10E0.book Page 7 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL No. 7 ITEM ROUTINE ODOMETER READINGS 600 mi (1000 km) or 1 month 4000 mi (7000 km) or 6 months √ √ √ √ √ √ 8000 mi 12000 mi 16000 mi 20000 mi (13000 km) (19000 km) (25000 km) (31000 km) or or or or 12 months 18 months 24 months 30 months 18 * Sidestand switch • Check operation and replace if necessary. 19 * Front fork • Check operation and for oil leakage. • Replace if necessary.
U1MC10E0.book Page 8 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL No. ITEM ROUTINE 27 * Control cables • Apply Yamaha chain and cable lube or engine oil thoroughly. 28 * Throttle grip • Check operation. • Check throttle grip free play, and adjust if necessary. • Lubricate cable and grip housing. 29 * Lights, signals and switches • Check operation. • Adjust headlight beam.
U1MC10E0.book Page 9 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU18771 EAU54130 Removing and installing panels 1 Panel A The panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a panel needs to be removed and installed. To remove the panel 1. Remove each headlight beam adjusting knob by removing the screw. 2 1. Panel B 1 1 1 7 1. Panel A 1. Screw 2. Headlight beam adjusting knob 2.
U1MC10E0.book Page 10 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT 1 2 3 To install the panel 1. Place the panel in its original position, and then install the bolt, screw and quick fastener. 2 1. Front cowling 2. Bolt 3. Quick fastener 4. Remove the bolt, screw and quick fastener, and then take the panel off. 3. Take the front cowling off as shown. 1 4 2 3 1. 2. 3. 4. 2. Place the front cowling in its original position, and then install the bolts and quick fasteners. 3.
U1MC10E0.book Page 11 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT 2 3 1 2 3 3 2 3. Pull the bottom of the panel outward, pull the front of the panel downward, and then slide the panel forward to release it in the rear as shown. 1 1 1. Panel B 2. Quick fastener screw 3. Bolt 3 2 1 1. Panel B 2. Install the seats. 2 3 7 2 1. Panel B To install a panel 1. Place the panel in the original position, and then install the bolts and the quick fastener screws. 1. Panel C 2.
U1MC10E0.book Page 12 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU19652 Checking the spark plugs The spark plugs are important engine components, which should be checked periodically, preferably by a Yamaha dealer. Since heat and deposits will cause any spark plug to slowly erode, they should be removed and checked in accordance with the periodic maintenance and lubrication chart. In addition, the condition of the spark plugs can reveal the condition of the engine.
U1MC10E0.book Page 13 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU19681 FUEL TANK ATMOSPHERE #2 #1 7 EAU19886 Engine oil and oil filter cartridge 2 The engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter cartridge replaced at the intervals specified in the periodic maintenance and lubrication chart.
U1MC10E0.book Page 14 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT 4. Remove the engine oil filler cap, the engine oil drain bolt and its gasket to drain the oil from the crankcase. 2 1 2 1 1. Engine oil drain bolt 2. Gasket TIP Skip steps 5–7 if the oil filter cartridge is not being replaced. 1. Oil filter wrench 2. Oil filter cartridge 1. O-ring TIP An oil filter wrench is available at a Yamaha dealer. 6.
U1MC10E0.book Page 15 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT ECA11620 Tightening torque: Oil filter cartridge: 17 Nm (1.7 m·kgf, 12 ft·lbf) NOTICE ● 8. Install the engine oil drain bolt and its new gasket, and then tighten the bolt to the specified torque. Tightening torque: Engine oil drain bolt: 43 Nm (4.3 m·kgf, 31 ft·lbf) 9. Refill with the specified amount of the recommended engine oil, and then install and tighten the oil filler cap.
U1MC10E0.book Page 16 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU20016 Final gear oil The final gear case must be checked for oil leakage before each ride. If any leakage is found, have a Yamaha dealer check and repair the vehicle. In addition, the final gear oil level must be checked and the oil changed as follows at the intervals specified in the periodic maintenance and lubrication chart. TIP The oil level should be at the brim of the filler hole.
U1MC10E0.book Page 17 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU20070 Tightening torque: Final gear oil drain bolt: 23 Nm (2.3 m·kgf, 17 ft·lbf) 5. Refill with the recommended final gear oil to the brim of the filler hole. Recommended final gear oil: Yamaha genuine shaft drive gear oil SAE 80 API GL-5 Oil quantity: 0.20 L (0.21 US qt, 0.18 Imp.qt) 7 6. Check the oil filler bolt gasket for damage, and replace it if necessary. 7.
U1MC10E0.book Page 18 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT reservoir cap. WARNING! Remove only the coolant reservoir cap. Never attempt to remove the radiator cap when the engine is hot. [EWA15161] NOTICE: If coolant is not available, use distilled water or soft tap water instead. Do not use hard water or salt water since it is harmful to the engine.
U1MC10E0.book Page 19 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT out with compressed air as shown. If the air filter element is damaged, replace it. 2 1 1 2 1. Air filter case cover 2. Screw 1. Fuel tank breather/overflow hose 4. Pull the air filter element out. 1 7 1. Air filter element 5. Lightly tap the air filter element to remove most of the dust and dirt, and then blow the remaining dirt 6. Insert the air filter element into the air filter case.
U1MC10E0.book Page 20 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU44734 Checking the engine idling speed EAU21384 Checking the throttle grip free play Check the engine idling speed and, if necessary, have it corrected by a Yamaha dealer. Engine idling speed: 1000–1100 r/min EAU21401 Valve clearance The valve clearance changes with use, resulting in improper air-fuel mixture and/or engine noise.
U1MC10E0.book Page 21 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU21756 Tires Tires are the only contact between the vehicle and the road. Safety in all conditions of riding depends on a relatively small area of road contact. Therefore, it is essential to maintain the tires in good condition at all times and replace them at the appropriate time with the specified tires. Tire air pressure The tire air pressure should be checked and, if necessary, adjusted before each ride.
U1MC10E0.book Page 22 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT Minimum tire tread depth (front and rear): 1.0 mm (0.04 in) Tire information EWA10481 WARNING ● EWA10581 WARNING ● ● ● It is dangerous to ride with a worn-out tire. When a tire tread begins to show crosswise lines, have a Yamaha dealer replace the tire immediately.
U1MC10E0.book Page 23 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT Front tire: Size: 120/70 ZR17M/C (58W) Manufacturer/model: BRIDGESTONE/BT023F F Rear tire: Size: 180/55 ZR17M/C (73W) Manufacturer/model: BRIDGESTONE/BT023R F FRONT and REAR: Tire air valve: TR412 Valve core: #9100 (original) ● ● speed riding to ride conservatively for approximately 100 km (60 mi) after installing a new tire. The tires must be warmed up before a high-speed run.
U1MC10E0.book Page 24 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU22073 Clutch lever Since this model is equipped with a hydraulic clutch, adjusting the clutch lever free play is not needed. However, it is necessary to check the clutch fluid level and check the hydraulic system for leakage before each ride. (See page 7-26.
U1MC10E0.book Page 25 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT Checking the front and rear brake pads cator groove has almost disappeared, have a Yamaha dealer replace the brake pads as a set. The front and rear brake pads must be checked for wear at the intervals specified in the periodic maintenance and lubrication chart.
U1MC10E0.book Page 26 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU40271 Checking the brake and clutch fluid levels Rear brake Specified brake and clutch fluid: DOT 4 brake fluid Before riding, check that the brake and clutch fluids are above the minimum level marks. Check the brake and clutch fluid levels with the tops of the reservoirs level. Replenish the brake and clutch fluids if necessary. Front brake EWA16030 WARNING 1. Minimum level mark Clutch 1.
U1MC10E0.book Page 27 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT and may result in vapor lock, and dirt may clog the ABS hydraulic unit valves. ECA17640 NOTICE Brake fluid may damage painted surfaces or plastic parts. Always clean up spilled fluid immediately. 7 The brake or clutch fluid reservoir diaphragm will lose its shape from the negative pressure if the fluid level goes down too far.
U1MC10E0.book Page 28 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU23114 EAU44273 Checking and lubricating the throttle grip and cable Checking and lubricating the brake and shift pedals The operation of the throttle grip should be checked before each ride. In addition, the cable should be lubricated by a Yamaha dealer at the intervals specified in the periodic maintenance chart. The throttle cable is equipped with a rubber cover. Make sure that the cover is securely installed.
U1MC10E0.book Page 29 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU43601 Checking and lubricating the brake and clutch levers EAU23213 Recommended lubricant: Silicone grease Checking and lubricating the centerstand and sidestand The operation of the brake and clutch levers should be checked before each ride, and the lever pivots should be lubricated if necessary.
U1MC10E0.book Page 30 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU23251 Recommended lubricant: Lithium-soap-based grease EAUM1652 Lubricating the rear suspension Lubricating the swingarm pivots The pivoting points of the rear suspension must be lubricated by a Yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart.
U1MC10E0.book Page 31 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU23272 EAU45511 Checking the front fork Checking the steering The condition and operation of the front fork must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart. Worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart. 1.
U1MC10E0.book Page 32 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU23291 Checking the wheel bearings EAU39525 Battery 2 1 3 The front and rear wheel bearings must be checked at the intervals specified in the periodic maintenance and lubrication chart. If there is play in the wheel hub or if the wheel does not turn smoothly, have a Yamaha dealer check the wheel bearings. 1. Battery 2. Positive battery lead (red) 3.
U1MC10E0.book Page 33 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT battery tends to discharge more quickly if the vehicle is equipped with optional electrical accessories. ECA16521 NOTICE To charge a VRLA (Valve Regulated Lead Acid) battery, a special (constant-voltage) battery charger is required. Using a conventional battery charger will damage the battery. 7 To store the battery 1.
U1MC10E0.book Page 34 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT 1 7 8 7 2 3 12 13 4 11 5 10 6 9 14 7 15 7 2. Remove the blown fuse, and then install a new fuse of the specified amperage. WARNING! Do not use a fuse of a higher amperage rating than recommended to avoid causing extensive damage to the electrical system and possibly a fire. [EWA15131] 1. 2. 3. 4. ABS motor fuse ABS solenoid fuse Fuel injection system fuse Backup fuse (for clock and immobilizer system) 5.
U1MC10E0.book Page 35 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT 3. Turn the key to “ON” and turn on the electrical circuit in question to check if the device operates. 4. If the fuse immediately blows again, have a Yamaha dealer check the electrical system. EAU40361 EAU54770 Headlight bulb Front turn signal/position light If a headlight does not come on, have a Yamaha dealer check its electrical circuit or replace the bulb.
U1MC10E0.book Page 36 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU27004 Replacing a rear turn signal light bulb or a tail/brake light bulb 5. Install the socket (together with the bulb) by turning it clockwise. 6. Install the passenger seat. EAU24313 Replacing the license plate light bulb 1. Remove the license plate light unit by removing the screws. 1. Remove the passenger seat. (See page 4-30.) 2.
U1MC10E0.book Page 37 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU54500 Auxiliary light 2 1 1. License plate light bulb 2. License plate light bulb socket 1 1 1. Auxiliary light 7 3. Remove the burnt-out bulb by pulling it out. 4. Insert a new bulb into the socket. 5. Install the socket (together with the bulb) by pushing it in. 6. Install the license plate light unit by installing the screws. EAU25871 Troubleshooting This model is equipped with LED-type auxiliary lights.
U1MC10E0.book Page 38 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT heaters or furnaces. Gasoline or gasoline vapors can ignite or explode, causing severe injury or property damage.
U1MC10E0.book Page 39 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT EAU42504 Troubleshooting charts Starting problems or poor engine performance 1. Fuel There is enough fuel. Check the battery. There is no fuel. Supply fuel. Check the fuel level in the fuel tank. 2. Battery The engine does not start. Check the battery. The engine turns over quickly. The battery is good. The engine turns over slowly.
U1MC10E0.book Page 40 Monday, July 30, 2012 4:56 PM PERIODIC MAINTENANCE AND ADJUSTMENT Engine overheating EWAT1040 WARNING ● ● Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled. Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape.
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM MOTORCYCLE CARE AND STORAGE EAU37833 Matte color caution ECA15192 NOTICE Some models are equipped with matte colored finished parts. Be sure to consult a Yamaha dealer for advice on what products to use before cleaning the vehicle. Using a brush, harsh chemical products or cleaning compounds when cleaning these parts will scratch or damage their surface. Wax also should not be applied to any matte colored finished parts.
U1MC10E0.book Page 2 Monday, July 30, 2012 4:56 PM MOTORCYCLE CARE AND STORAGE ● ● ● off any detergent residue using plenty of water, as it is harmful to plastic parts. Do not use any harsh chemical products on plastic parts. Be sure to avoid using cloths or sponges which have been in contact with strong or abrasive cleaning products, solvent or thinner, fuel (gasoline), rust removers or inhibitors, brake fluid, antifreeze or electrolyte.
U1MC10E0.book Page 3 Monday, July 30, 2012 4:56 PM MOTORCYCLE CARE AND STORAGE windshield. Before using them, make a test by polishing an area which does not affect your visibility. 8 After cleaning 1. Dry the motorcycle with a chamois or an absorbing cloth. 2. Use a chrome polish to shine chrome, aluminum and stainlesssteel parts, including the exhaust system. (Even the thermally induced discoloring of stainlesssteel exhaust systems can be removed through polishing.) 3.
U1MC10E0.book Page 4 Monday, July 30, 2012 4:56 PM MOTORCYCLE CARE AND STORAGE EAU26243 Storage Short-term Always store your motorcycle in a cool, dry place and, if necessary, protect it against dust with a porous cover. Be sure the engine and the exhaust system are cool before covering the motorcycle. ECA10810 NOTICE ● ● Storing the motorcycle in a poorly ventilated room or covering it with a tarp, while it is still wet, will allow water and humidity to seep in and cause rust.
U1MC10E0.book Page 5 Monday, July 30, 2012 4:56 PM MOTORCYCLE CARE AND STORAGE TIP Make any necessary repairs before storing the motorcycle.
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM SPECIFICATIONS Dimensions: Overall length: 2230 mm (87.8 in) Overall width: 750 mm (29.5 in) Overall height: 1325/1455 mm (52.2/57.3 in) Seat height: 805/825 mm (31.7/32.5 in) Wheelbase: 1545 mm (60.8 in) Ground clearance: 130 mm (5.12 in) Minimum turning radius: 3100 mm (122.
U1MC10E0.book Page 2 Monday, July 30, 2012 4:56 PM SPECIFICATIONS Secondary reduction ratio: 2.698 (35/37 x 21/27 x 33/9) Transmission type: Constant mesh 5-speed Operation: Left foot operation Gear ratio: 1st: 2.529 (43/17) 2nd: 1.773 (39/22) 3rd: 1.348 (31/23) 4th: 1.077 (28/26) 5th: 0.929 (26/28) Chassis: Frame type: Diamond Caster angle: 26.00 ° Trail: 109 mm (4.
U1MC10E0.book Page 3 Monday, July 30, 2012 4:56 PM SPECIFICATIONS Spring/shock absorber type: Coil spring/gas-oil damper Wheel travel: 125.0 mm (4.92 in) Electrical system: Ignition system: TCI Charging system: AC magneto Battery: Model: GT14B-4 Voltage, capacity: 12 V, 12.0 Ah Headlight: Bulb type: Halogen bulb Bulb voltage, wattage × quantity: Headlight: 12 V, 60.0 W/55.0 W × 2 Tail/brake light: 12 V, 5.0 W/21.0 W × 2 Front turn signal/position light: LED Rear turn signal light: 12 V, 21.
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM CONSUMER INFORMATION EAU26353 Identification numbers EAU26381 Key identification number EAU26400 Vehicle identification number Record the key identification number, vehicle identification number and model label information in the spaces provided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehicle is stolen. 1 KEY IDENTIFICATION NUMBER: VEHICLE IDENTIFICATION NUMBER: 1.
U1MC10E0.book Page 2 Monday, July 30, 2012 4:56 PM CONSUMER INFORMATION EAU26520 Model label EAU48270 Vehicle Emission Control Information label 1 1. Model label The model label is affixed to the frame under the passenger seat. (See page 4-30.) Record the information on this label in the space provided. This information will be needed when ordering spare parts from a Yamaha dealer. 1.
U1MC10E0.book Page 3 Monday, July 30, 2012 4:56 PM CONSUMER INFORMATION EAU26551 Reporting safety defects If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation, U.S.A.
U1MC10E0.
U1MC10E0.book Page 5 Monday, July 30, 2012 4:56 PM CONSUMER INFORMATION EAU26632 Maintenance record Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder that maintenance work is required. It is not acceptable proof of maintenance work.
U1MC10E0.
U1MC10E0.book Page 7 Monday, July 30, 2012 4:56 PM CONSUMER INFORMATION EAU26663 YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED WARRANTY Yamaha Motor Corporation, U.S.A. hereby warrants that new Yamaha motorcycles will be free from defects in material and workmanship for the period of time stated herein, subject to certain stated limitations.
U1MC10E0.book Page 8 Monday, July 30, 2012 4:56 PM CONSUMER INFORMATION WARRANTY QUESTIONS AND ANSWERS CUSTOMER SERVICE Q. What costs are my responsibility during the warranty period? A. The customer’s responsibility includes all costs of normal maintenance services, non-warranty repairs, accident and collision damages, and oil, oil filters, air filters, spark plugs, and brake shoes.
U1MC10E0.book Page 9 Monday, July 30, 2012 4:56 PM CONSUMER INFORMATION EAU26751 YAMAHA EXTENDED SERVICE (Y.E.S.) Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended Service (Y.E.S.). In addition, Travel and Recreation Interruption Protection (TRIP) is included at no extra cost.
U1MC10E0.book Page 10 Monday, July 30, 2012 4:56 PM CONSUMER INFORMATION We urge you to act now. You’ll get the excellent benefits of TRIP coverage right away, and you’ll rest easy knowing you’ll have strong factory-backed protection even after your Yamaha Limited Warranty expires. A special note: If visiting your dealer isn’t convenient, contact Yamaha with your Primary ID number (your frame number). We’ll be happy to help you get the Y.E.S. coverage you need. Yamaha Service Marketing P.O.
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM INDEX A ABS....................................................... 4-24 ABS warning light.................................... 4-3 Accessory box....................................... 4-35 Air filter element, cleaning..................... 7-18 Auxiliary DC jack................................... 4-44 Auxiliary light......................................... 7-37 D Dimmer/Pass switch ............................. 4-21 D-mode (drive mode).....................
U1MC10E0.book Page 2 Monday, July 30, 2012 4:56 PM INDEX Start/Engine stop switch ....................... 4-22 Starting the engine ................................. 6-1 Steering, checking ................................ 7-31 Storage ................................................... 8-4 Storage compartments ......................... 4-34 Swingarm pivots, lubricating................. 7-30 T Throttle grip and cable, checking and lubricating ...........................................
U1MC10E0.
U1MC10E0.book Page 1 Monday, July 30, 2012 4:56 PM EAU51390 For your best ownership experience, think Genuine Yamaha! Genuine Yamaha Parts – Genuine Yamaha replacement parts are the exact same parts as the ones originally equipped on your vehicle, providing you with the performance and durability you have come to expect.
PRINTED ON RECYCLED PAPER PRINTED IN JAPAN 2012.08-0.
