Owner`s manual

ELB-01 Owner’s Manual
55
Voice Controls and Effects
3
DYNAMIC
This effect (also called compression) “squeezes” the
overall dynamic range of the sound, and has a gain
control—letting you make soft sounds louder, and
thus give more “punch” to the sound.
EQ/ENHANCER
EQ
This processing tool lets you change the level for
specific frequency ranges in the sound, and affects the
overall sound quality.
ENHANCER
This effect emphasizes and enhances the overtones in
the high frequency sound range overtone—not
merely making the sound brighter, but giving it more
clarity and presence.
THRU
Bypass control. This cancels the effect processing.
Sensitivity 0 – 127 Determines the degree to which
the wah filter is affected by your
playing touch.
Dry/Wet D63>W – D<W63 Determines the balance of the
original sound and the effect
sound.
No. Type
01 COMPRESSOR
02 NOISE GATE
Parameter Value Description
Attack 1 – 40 msec Determines how soon the
compression effect is applied,
once the compressor has been
triggered (as a result of Threshold
below.
Release 10 – 680 msec Determines how soon the
compressor returns to its normal
gain, once the trigger signal
drops below the Threshold point.
Threshold Compressor:
-48 – -6 dB
Noise Gate:
-72 – -30 dB
Determines the level of the input
signal required to trigger the
compressor. Signals at a level
below the Threshold pass
through unaffected; signals at
and above the Threshold are
compressed.
Ratio 1.0 – 20.0 Determines the amount of
compression of the sound (for
signals passing the Threshold).
This is expressed as a ratio—the
change in output signal relative to
the change in input. The range
here is 1/1 (no change in output
signal, hence no compression) to
20/1. Higher ratios result in
greater compression.
OutputLevel 0 – 127 Determines the overall output of
the compressed signal. Use this
to bring up the overall level after
you’ve reduced the dynamic
range with compression.
No. Type
01 ST 2BAND EQ
02 ST 3BAND EQ
03 XG 3BAND EQ
04 EQ DISCO
05 EQ TEL
Parameter Value Description Parameter Value Description
EQ LowFreq. 50 – 2.0k Hz
ST 2Band EQ:
32 – 2.0k Hz
Determines the central frequency
of the low frequency range that is
to be boosted or cut.
EQ Low Gain -12 – +12 dB Determines the amount over
which the low frequency range is
boosted or cut.
EQ Mid.Freq 100 – 16k Hz Determines the central frequency
of the middle frequency range
that is to be boosted or cut.
EQ Mid.Gain -12 – +12 dB Determines the amount over
which the middle frequency
range is boosted or cut.
EQ M Width 0.1 – 12.0 Determines the bandwidth or the
range of frequencies around the
specific middle frequency that is
to be boosted or cut. Lower
values let you narrow in on a
specific frequency, while higher
values select a broader range of
frequencies to be affected.
EQ Hi.Freq 500 Hz – 16k Hz Determines the central frequency
of the high frequency range that
is to be boosted or cut.
EQ Hi.Gain -12 – +12 dB Determines how much increase/
decrease the wave frequency
point of EQ high frequency.
No. Type
06 HM ENHANCER
07 XG HM ENHNCE
Parameter Value Description
HPF Cutoff 500 Hz – 16k Hz Determines the cutoff frequency
of the low pass filter. Frequencies
above this value are cut or filtered
out.
Drive 0 – 127 Determines the amount or depth
of the Enhancer effect.
Mix Level 0 – 127 Determines how much of the
processed enhanced sound is
mixed together with the original
sound.
No. Type
01 Thru