Owner's Manual

DSP-R10 Owner’s Manual
18
Error messages indicating a need for attention
Names marked with an asterisk (*) are Unit IDs.
NOTE
If multiple issues occur at the same time, press the [U] or [D] key to view the corresponding error messages.
LCD
Message
Color
Indicator
Status
Description Possible solution
*[ERR T0#]
TWINLANe
WRONG LOOP
Red
(flashing)
Fiber optic cable is not connected properly.
A number sign (#) indicates the error
description.
1: Signal is looped back to the unit itself
(IN-OUT).
2: Input connectors are connected to each
other (IN-IN).
3: Output connectors are connected to
each other (OUT-OUT).
Check the cable connection.
*[ERR T07]
TWINLANe
OPEN LOOP
Ye l l o w
(lit steadily)
Fiber optic cable is not connected properly.
The TWINLANe network loop is not closed.
Check the cable connection.
*[ERR T12]
TWINLANe
T V B OP IP
Ye l l o w
(lit steadily)
An error has occurred with the optical
transceiver module on the HY256-TL.
T: Temperature, V: Voltage, B: Bias current,
OP: Output Power, IP: Input Power
• Make sure that the cable is securely inserted.
• Use a commercially-available cleaning tool fo
r
f
iber optics to clean both ends of the cabl
e and
the connectors on the card.
• Change to a different cable.
If the solutions above do not resolve the issue
,
have the unit checked by an authorized
t
echnician, although the problem will not aff
ect
oper
ation of the unit. Please contact your Yamaha
dealer.
*[ERR T0#]
CONSOLE NETWK
WRONG LOOP
Red
(flashing)
Ethernet cable is not connected properly.
A number sign (#) indicates the error
description.
4: Signal is looped back to the unit itself
(IN-OUT).
5: Input connectors are connected to each
other (IN-IN).
6: Output connectors are connected to
each other (OUT-OUT).
Check the cable connection.
*[ERR T08]
CONSOLE NETWK
OPEN LOOP
Ye l l o w
(lit steadily)
Ethernet cable is not connected properly.
The Console network loop is not closed.
Check the cable connection.
*[ERR W01]
BNC UNLOCK
Red
(flashing)
The unit is unable to lock to the word clock
that is being input from the WORD CLOCK
IN connector (if the WORD CLOCK IN has
been selected as the clock source).
Check the external device that is supplying the
word clock.
*[ERR W02]
DATA CORRUPT
TRY RE-SYNC
Red
(flashing)
Mix data inside the unit has been corrupted.
The loading of a file or data syncing might
have been interrupted due to power outage.
Try data syncing again by transmitting data from
the control surface.
*[ERR P01]
POWER A OFF
Ye l l o w
(lit steadily)
Power is not supplied from power supply
unit A.
Make sure that the power switch on power supply
unit A is turned on, and that the power cord is
connected to the unit and power supply unit A.
*[ERR P02]
POWER B OFF
Ye l l o w
(lit steadily)
Power is not supplied from power supply
unit B.
Make sure that the power switch on power supply
unit B is turned on, and that the power cord is
connected to the unit and power supply unit B.
*[ERR C11]
LOW BATT
Ye l l o w
(lit steadily)
The backup battery voltage is down to 2.8V
or lower.
Please contact your Yamaha dealer immediately
and ha
v
e qualified Yamaha service personnel
replace the backup battery.
*[ERR C12]
NO BATT
Ye l l o w
(lit steadily)
The backup battery voltage is down to
2.45V or lower.
Please contact your Yamaha dealer immediately
and have qualified Yamaha service personnel
replace the backup battery.