安全上のご注意 ご使用の前に、必ずこの「安全上のご注意」をよくお読みください。 ここに示した注意事項は、製品を安全に正しくご使用いただき、お客様や他の方々へ の危害や財産への損害を 未然に防止するためのものです。必ずお守りください。 お子様 がご使用になる 場合は、保護者の 方が以下の内容 をお子様にご徹 底くださいま すようお願いい たしま す。 お読みになったあとは、使用される方がいつでも見られる所に必ず保管してください。 ■ 記号表示について この製品や取扱説明書に表示されている記号には、 次のような意味があります。 「ご注意ください」という注意喚起を示します。 〜しないでくださいという「禁止」を示します。 「必ず実行」してくださいという強制を示します。 ■ 「警告」と「注意」について 以下、 誤った取り扱いをすると生じることが想定される内容を、 危害や損害の大きさと切迫の程度を明示するた めに、 「警告」と「注意」に区分して掲載しています。 警告 この表示の欄は、 「死亡す る可能性または重傷を負 う可能性が想定される」 内容です。 注意 この表示の欄は、 「傷害を 負う可能性または物的損
警告 電源 / 電源コード 水に注意 電源は必ず交流 100V を使用する。 本体の上に花瓶や薬品など液体の入ったものを置かない。 エアコンの電源など交流200V のものがあります。誤って接 続すると、 感電や火災のおそれがあります。 また、 浴室 や雨天時の屋外など湿気の多いと ころで使用しな い。 必ず実行 禁止 電源プラグにほこりが付着してい る場合は、 ほこりを きれい に拭き取る。 感電や火災、 または故障の原因になります。 濡れた手で電源プラグを抜き差ししない。 感電のおそれがあります。 感電やショートのおそれがあります。 必ず実行 禁止 電源コード / プラグは、 必ず付属のものを使用する。 他の電源コード / プラグを使用すると、発熱や感電の原因に なります。 火に注意 本体の上にろうそくなど火気のあるものを置かない。 ろうそくなどが倒れたりして、 火災の原因になります。 必ず実行 電源コードをストーブなどの熱器 具に近づけたり、 無 理に曲 げたり、 傷つけた りしない。 また、電源コードに重いも のをの 禁止 せない。 電源コードが破損し、 感電や火災の原因にな
組み立て 必ず実行 手入れ 組み立てる前に、 必 ず本書の組み立て方の説明をよく お読み ( 艶出し仕上げモデルの場合 )本体のほこりや汚れは、柔らか ください。 手順どおりに正しく組み立てない と、 楽器が破損した りお客 い布で軽く拭き取る。 強く拭くと、ほこりの粒子で本体の表面に傷 がつく場合があ 様がけがをしたりする原因になります。 必ず実行 本体を手入れすると きは、 ベンジンやシ ンナー、 洗剤、化学ぞ うきんなどは使用しない。 設置 禁止 直射日光の あたる場 所 (日中 の車内な ど) やス トーブの近 く など極端に温度が高くなるところ、逆に温度が極端に 低いと 禁止 本体のパネルや鍵盤が変色 / 変質する原因になります。お手 入れは、乾いた 柔らかい布、もしく は水を固 くしぼった 柔ら かい布をご使用ください。 ころ、 また、ほこりや振動の多いところで使用しない。 本体のパネルが変形したり、内部の部品が故障したり する原 使用時の注意 因になります。 禁止 ります。 テレビやラ ジオ、 ス テレオ、携帯電話 など他の 電気製品の 近 くで使用しない。
イス データの保存 不安定な場所に置かない。 作成したデータの保存とバックアップ イスが転倒して、 お 客様や他の方々がけがをする原因 になり ます。 下記の データは、保存前に 電源を切る と消えて しまいます。 保存しておきたいデータは 「ユーザー」画面 (24 ページ ) や、 USB 記憶装置 (USB フラッシュメモリー/ フロッピーディ 禁止 イスで遊んだり、 イスを踏み台にしたりしない。 このイスは楽器演奏用です。イスを遊び道具や踏み台 にする 禁止 必ず実行 ・ 録音/編集したソング(本書102ページ、 117ページ、別冊 と、 イス が転倒した りこわれ たりして、お客様 がけがをす る 原因になります。 クイックガイド 21ページ) ・ スタイル制作(74ページ)で制作/編集したスタイル イスには二人以上ですわらない。 ・ ボイス編集 (55ページ)で編集したボイス ・ 設定を登録したワンタッチセッティング (別冊クイックガ イスが転倒したりこわれたりして、お客様がけがをす る原因 になります。 イド 30ページ) ・ MIDI設定編集 (162ページ)で編集した
このたびは、ヤマハクラビノーバをお買い上げいただきまして、まことにありがとうございます。 クラビノーバの優れた機能を十分に生かして演奏をお楽しみいただくため、本書をお読みください。また、お読みに なったあとも、いつでもご覧になれるところに大切に保管してください。 取扱説明書について この取扱説明書は、以下のように構成されています。 本書 準備 (16ページ)...............................最初にお読みください。 基本操作 (21ページ) .......................画面の操作など、操作の基本を説明します。 本編 (37ページ)...............................本体を便利に使いこなすための操作を説明します。 付録 (168ページ)............................
付属品 ( お確かめください ) □保証書 □ヤマハ オンラインメンバー製品ユーザー登録のご案内 □取扱説明書 ( 本書 ) □取扱説明書別冊「クイックガイド」 □取扱説明書別冊「データリスト」 □ヘッドフォン □イス ( 高さ調節付き ) ■ 調律について 調律の必要ありません。 ■ お引越しの際は 通常の荷物と一緒にお運びいただけます。組み立てた状態でも、組み立てる前の部品に分解した状態でも問題ありませ んが、本体は立てかけたりせず、必ず水平に置いてお運びください。また、大きな振動、衝撃を与えないでください。 組み立てた状態でお運びいただいた場合は、設置の際、各部のネジのゆるみを確認し、ゆるんでいる場合は締め直して ください。 CVP-405/403/401 取扱説明書 7
クラビノーバの世界へようこそ! 自然な鍵盤タッチ GH鍵盤では、低音部は重く、高音部は軽く、グランドピアノに近い鍵盤の重さで自然な弾き心地が得ら れます。CVP-405/403に搭載されているGH3鍵盤では、さらに、グランドピアノのように、ペダルを 踏まずに音をつなげる奏法や高速の同音連打も可能です。 オーディオ録音する (CVP-405/403) 演奏をオーディオ録音してみましょう ...........................別冊クイックガイド41ページ ご自分の演奏をUSB記憶装置にオーディオ録音することができます。ギターやマイクを 楽器につなげば、ギターと鍵盤演奏のアンサンブルや弾き語りの録音を楽しめます。 演奏する ピアノの音で演奏しましょう......................................... 別冊クイックガイド 8ページ ワンタッチでピアノ設定を呼び出すことができます。本格的なグランドピアノの音で、演 奏をお楽しみください。 いろいろな楽器音(ボイス)で演奏しましょう .................
練習する 画面に譜面を表示させて演奏しましょう .......................別冊クイックガイド 17ページ 画面に譜面を表示させることができます。譜面を見ながら練習しましょう。 ガイドランプを使いましょう.......................................別冊クイックガイド 19ページ 鍵盤ガイドランプが、鍵盤を弾くタイミングや押さえる鍵盤位置などを教えてくれます。 ご自分の演奏を録音しましょう....................................別冊クイックガイド 21ページ ご自分の演奏を録音して、本体やUSB記憶装置(USBフラッシュメモリー /フロッピー ディスクなど)に保存できます。録音した演奏を聞けば、演奏の弱点を見つけたりするの に役立ちます。 インターネットに接続する インターネットダイレクト接続機能を使いましょう ..................................
目次 ミュージックファインダーの便利な使い方 .......................68 準備 レコードを検索する ............................................................ 68 お気に入りのレコードを簡単に呼び出す.......................... 70 クラビノーバの世界へようこそ!.................................. 8 各部の名称 .............................................................. 12 音を出してみましょう ............................................... 14 譜面立てを使う.....................................................................16 譜面止めを使う(CVP-405/403) ....................................
目次 楽器本体のスピーカーから外部機器の音を出す ( 4[AUX IN]端子 ) ............................................................151 楽器本体の画面をテレビに映し出す ( 5[VIDEO OUT] 端子)(CVP-405) ..............................151 フットスイッチやフットコントローラーを使う (6[AUX PEDAL] 端子)................................................. 152 ペダル(フットスイッチやフットコントローラー含む )に 機能を割り当てる ..............................................................152 準備 外部 MIDI機器と接続する (7[MIDI]端子).....................156 コンピューター、USB機器、 およびインターネットと接続す る (789)) ...................................
各部の名称 準 備 ! 電源 .............................................................................................14ページ デバ イ ス 2 [USB TO DEVICE ]端子................................... 35ページ、 157ページ # [音量] ..........................................................................................15ページ $ [デモ] ........................................................ 別冊クイックガイド 3ページ 4 [画面コントラスト] .................................................................. 19ページ 5 [A]〜[J] .......................................
準 備 ピアノ設定 P [ピアノリセット] ..................................... 別冊クイックガイド 8ページ ボタン名を50音順に並べた「パネルボタン早見表」 が巻末(188ページ)にあります。ご活用ください。 レジストレーションメモリー Q レジストレーションバンク[-][+] .............................................90ページ S [1]〜[8] .....................................................................................89ページ 楽器本体底面の左端手前にある端子や、楽器本体 底面の左端後ろにある端子群については、150 ページを参照してください。 ボイスコントロール T ボイスボタン .........................................
音を出してみましょう 1 電源コードを接続する 最初に本体側のプラグを差し込み、次にコンセント側(家庭用AC100V)のプラ グを差し込みます。 準 備 2 キーカバーを開ける CVP-405/403: 本体正面のくぼみに手を掛け、キーカバーを持ち上げます。 CVP-401: 少し持ち上げて、奥へ押し込みます。 CVP-405/403 キーカバーを開閉するときは、両手 で静かに行ない、途中で手を離さな いでください。また、ご自分や周り の方、特にお子様などが、キーカ バーの端と本体の間に手や指をはさ まないようご注意ください。 手や指をはさまないように注意 3 キーカバーを開けるとき、キーカ バーの上に金属や紙片などを置かな いでください。 本体の内部に落ちて取り出せなくな り、感電、ショート、発火や故障な どの原因になります。 CVP-405/403/401 取扱説明書 手や指をはさまないように注意 電源を入れる 本体パネル右の[電源]ボタンを押すと、電源が入ります。 本体パネル中央の画面に表示が現れます。また、本体前面左の電源ランプが点灯 します。 電源ランプが点灯 14 CVP
4 鍵盤を弾く 鍵盤を弾いて、音を出してみましょう。 準 備 音量を調節する 音量は、本体パネル左の[音量]ダイアルで調節します。鍵盤を弾いて音を出しな がら調節してください。 5 電源を切る もう一度[電源]ボタンを押します。 画面の表示が消え、本体前面左の電源ランプも消灯します。 6 キーカバーを閉める CVP-405/403: 本体パネル上部の金属部分を持ち、キーカバーを下ろします。 CVP-401: 手前に引いて、静かに降ろします。 CVP-405/403 手や指をはさまないように注意 CVP-401 手や指をはさまないように注意 CVP-405/403/401 取扱説明書 15
準備 譜面立てを使う 譜面立てを立てるとき/倒すときは、 途中で手を離さないでください。 立てるとき CVP-405/403: 譜面立てを手前に起こします。 譜面立ては、一定の位置で固定されます。 CVP-401: 1. 譜面立てを、止まるまで手前に起こします。 2. 譜面立て裏にある左右2つの金具を下ろします。 準 備 3. 金具が固定される位置まで、譜面立てを戻します。 CVP-401 CVP-405/403 譜面立ては、金具が固定されない位 置で使用または放置しないでくださ い。 倒すとき (CVP-405/403) 譜面立てを倒す前に、譜面止め(下 記)を下ろしてください。 譜面止めを上げた状態では、譜面立 てを倒せません。 また、譜面止めを上げたまま譜面立 てを倒すと、譜面立てと譜面止めの 間に指をはさみ、お客様がけがをす るおそれがあります。 CVP-405/403: 譜面立ての中央部を持ち上げてから、回転させるようにゆっくり戻します。 CVP-401: 1. 譜面立てを、止まるまで手前に起こします。 2. 譜面立て裏にある左右2つの金具を上げます。 3.
譜面止めを使う (CVP-405/403) 譜面立てに置いた楽譜のページを止めます。 上げるとき 準 備 下ろすとき ヘッドフォンを使う ヘッドフォンを使う場合は、楽器本体底面の左側にある[PHONES]端子に接続します。 接続端子は2つありますので、ヘッドフォンを2本接続して2人で演奏を楽しむこともで きます。1本だけ接続する場合は、どちらの端子を使っても構いません。 大きな音量で長時間ヘッドフォンを 使用しないでください。 聴覚障害の原因になります。 CVP-401 CVP-405/403 INPUT VOLUME MIN MIC. LINE IN MIC.
ヘッドフォンハンガーを取り付ける 本体には、取り付け式のヘッドフォンハンガーが同梱されています。ヘッドフォンハン ヘッドフォンハンガーにヘッドフォ ン以外のものを掛けないでくださ い。本体またはヘッドフォンハン ガーが破損する場合があります。 ガーを取り付けると、本体にヘッドフォンを掛けられます。 付属のネジ(4×10mm)2本で、図のように取り付けてください。 CVP-405/403 CVP-401 準 備 ヘッドフォンを接続したままスピーカーから音を出す 1 設定画面を表示させます: [ファンクション]→[J]UTILITY→タブ切替[E][ F]CONFIG 2 2 [3▲▼]/[4▲▼](SPEAKER)ボタンを押して、ONを選びます。 ヘッドフォンだけで音を聞く 上記手順1の画面で[3▲▼]/[4▲▼](SPEAKER)ボタンを押して、OFFを 選びます。 OFFを選ぶと本体のスピーカーが鳴らず、ヘッドフォンを使ってのみ音を聞 くことができます。 画面に表示される言語を切り替える 画面に表示されるメッセージ、ファイル名などの言語を指定します。 1 設定画面を表示させます: [
画面を調整 / 設定する 画面のコントラスト(明暗比)を調整する 画面の左上にある[画面コントラスト]つまみを回して、画面のコントラストを調整します。 準 備 画面の明るさを調整する(CVP-405/403) 画面のバックライトの明るさを調整します。 1 設定画面を表示させます: [ファンクション]→[J] UTILITY→タブ切替[E][F]CONFIG 2 2 [2▲▼]ボタンを押して、バックライトの明るさを調整します。 CVP-405/403/401 取扱説明書 19
オープニング画面にオーナーネーム(OWNER NAME) を入力する オープニング画面(電源を入れたときに表示される画面)に、あなたの名前を表示できま す。 CVP-405 準 備 1 2 設定画面を表示させます: [ファンクション]→[J] UTILITY→タブ切替[E][ F]OWNER [I](OWNER NAME)ボタンを押して、名前入力用の画面を表示させます。 文字の入力方法は、31ページを参照してください。 楽器本体のバージョンを確認する この楽器のバージョンを確認するには、上記手順1の画面で[7▲▼]/[8▲▼] (VERSION)ボタンを押してバージョンを表示させます。[EXIT]ボタンを押すと、 元の画面に戻ります。 20 CVP-405/403/401 取扱説明書
基本操作 メッセージの言語を変える 画面のメッセージの言語を切り替えます。 1 設定画面を表示させます: [ファンクション]→[J]UTILITY→タブ切替[ E][F]OWNER 2 [4▲▼]/[5▲▼](LANGUAGE)ボタンを押して、言語を切り替えます。 3 [戻る]ボタンを押して、元の画面に戻します。 画面に表示されるメッセージなども、 ここで選んだ言語で表示されます。 基 本 操 作 2 画面に表示されるメッセージについて 操作中、操作をスムーズに導くために、画面にメッセージが表示されることがありま す。メッセージが表示されたら対応するボタンを押してください。 このメッセージの場合は、[F](YES) ボタンを押すと MEDIA(USBフラッシュメモリー /フロッピーディ スクなどのUSB記憶装置)をフォーマットできます。 CVP-405/403/401 取扱説明書 21
目的の画面をすばやく表示させる ( ダイレクトアクセス ) 目的の画面をすばやく表示させる ( ダイレクトアクセス ) ダイレクトアクセス機能を使って、目的の画面をすばやく表示させることができます。 1 2 [ダイレクトアクセス]ボタンを押します。 画面に、目的のボタンを押すように促すメッセージが表示されます。 表示させたい設定画面に対応したボタンを押します。 ダイレクトアクセスできる機能については、別冊データリスト「ダイレクトアク セス一覧表」を参照してください。 例) 基 本 操 作 ガイド機能の設定画面を表示させる [ダイレクトアクセス]ボタンを押してから、[ガイド]ボタンを押します。 1 2 ダイレクトアクセスでメイン画面に戻る 現在どの画面を表示させていても、[ダイレクトアクセス]ボタンを押してから[戻 る]ボタンを押すとメイン画面に戻れます。 22 CVP-405/403/401 取扱説明書
基本的な画面(メイン画面、選択画面)について 基本的な画面(メイン画面、選択画面)について よく使う画面としてメイン画面と選択画面があります。各画面の表示の意味や、操作方 法などをご説明します。 メイン画面の表示 メイン画面を見れば、今どのボイスを選んでいるか、どのスタイルを選んでいるかな ど、パネルの設定状態がひとめでわかります。演奏中に表示させておくと便利です。 7 ) CVP-405/403 8 ! 7 CVP-401 8 ! 9 9 1 1 ダイレクトアクセスでメイン画面に 戻る 現在どの画面を表示させていても、 [ダイレクトアクセス]ボタンを押し てから[戻る]ボタンを押すとメイン 画面に戻れます。 基 本 操 作 6 2 4 3 5 3 62 5 4 1 ボイス名 ・(右端の表示が「右手1」 )右手1パートで選ばれているボイスが表示されます(38ページ)。 ・(右端の表示が「右手2」 )右手2パートで選ばれているボイスが表示されます(38ページ)。 ・(右端の表示が「左手」)左手パートで選ばれているボイスが表示されます (38ページ)。 左手ホールド機能が
基本的な画面(メイン画面、選択画面)について 選択画面の構成と基本操作 選択画面とは、下記のボタンを押したときに表示される画面です。選択画面では、ボイスやスタイルなどを選べます。 ボイスボタン レジストレーションバンクボタン ソング選択ボタン スタイルボタン 基 本 操 作 選択画面の構成 ・データの保存場所 プリセット ユーザー USB 内蔵のデータがある場所 録音や編集をして保存したデータがある場所 USB記憶装置(USBフラッシュメモリー/ フロッピーディスクなど)に入っているデー タがある場所 この取扱説明書では、このページ以降USBフラッシュメモリー/フロッピーディスクなどのUSB記憶装置をUSB記憶装置と表記しています。 ・データの形式 データはファイルとして保存されています。ファイルはいくつかまとめてフォルダーに入れられます。 フォルダー A ファイル フォルダーを 表すアイコン 24 CVP-405/403/401 取扱説明書
基本的な画面(メイン画面、選択画面)について 選択画面の基本操作 1 ファイルの保存先から選ぶ [USB]ボタンまたは[ユーザー ]ボタ ンを押して、ファイルのある場所 (USB/ユーザー )から目的のファイ ルを選ぶこともできます。 [USB]/[ユーザー ]→[A]ソング/ [B]スタイル/[F]ボイス→[A]〜[J] 3 4 3 2 1 2 3 基 本 操 作 3 タブ切替[ E][ F]ボタンを押して、ファイルが保存されている場所を選びます。 [1▲]〜[7▲]ボタン(ボイス選択画面では[1▲]〜[5▲]ボタン、ソング/スタイ ル選択画面では[1▲]〜[6▲]ボタン)を押して、ページをめくります。 ファイルを選びます。ファイルを選ぶには、ふたとおりの方法があります。 ・[A]〜[J]ボタンを押します。 ・[データダイアル]でファイルを選んで[エンター ]ボタンを押して確定します。 4 [戻る]ボタンを押して、元の画面に戻します。 フォルダーを閉じてひとつ上の階層を表示させる 現在表示されている(開かれている)フォルダーを閉じてひとつ上の階層を表示さ せるには、[8▲](上へ)
基本的な画面(メイン画面、選択画面)について 選択画面のファイル / フォルダーに関する操作 ・データを保存する .................................................................................................... 27ページ ・ファイル/フォルダーをコピーする....................................................................... 28ページ ・ファイルを移動する ................................................................................................ 29ページ ・ファイル/フォルダーを削除する .......................................................................... 29ページ ・ファイル/フォルダーの名前を変える......................
基本的な画面(メイン画面、選択画面)について データを保存する あなたが作ったデータ(録音したソング、編集したボイスなど)をファイルとして保存し ます。 1 ソングクリエーターやボイス編集など、データ制作の画面にある[SAVE](セー ブ=保存)ボタンを押します。 該当するデータの選択画面が表示されます。保存は、選択画面で行ないます。 楽器本体に保存できる容量 楽器本体に保存できる容量は、何も 保存されないときで約1.
基本的な画面(メイン画面、選択画面)について プロテクトがかかったソングの制限 市販のミュージックデータ(ソング)の中には、コピー防止や誤消去防止のために プロテクトがかかっているものがあります。プロテクトがかかったソングは、ソ ング名の左上に下記のような表示が出ます。 基 本 操 作 Prot. 1 内蔵のソングを「ユーザー」画面に保存したものや、DOC(ディスクオー ケストラコレクション) 、ピアノプレーヤ用のミュージックデータです。 USB記憶装置にコピー /移動/保存できません。 Prot. 2 Orig ヤマハのプロテクトフォーマットが掛かったソングです。コピーができませ ん。 「ユーザー」画面とUSBフラッシュメモリーに移動/保存できます。 Prot. 2 Edit 上記「Prot. 2 Orig」を編集し、保存したソングです。編集元のファイルと 同じフォルダーに保存します。コピーができません。 「ユーザー」画面と USBフラッシュメモリーに移動/保存できます。 Prot.2 OrigとProt.2 Editの扱い Prot.2 OrigとProt.
基本的な画面(メイン画面、選択画面)について ファイルを移動する ファイルの移動では、ファイルを切り取って移動先に貼り付ける、という作業をしま す。 1 2 3 移動したいファイルがある画面を表示させます。 [2▼](カット)ボタンを押して、ファイルを切り取ります。 画面下部に、カットに関する画面が表示されます。 基 本 操 作 [A]〜[J]ボタンを押して、カットしたいファイルを選びます。 ファイルの選択を解除するときは、もう一度同じ[A]〜[J]ボタンを押します。 ■ 表示されているファイルをすべて選ぶ [6▼](ALL)ボタンを押すと、画面に表示されているすべてのファイル(画面に現 れていない別ページも含む)を選べます。 ファイルの選択を解除するときは、もう一度[6▼](ALL OFF)ボタンを押します。 4 5 6 [7▼](OK)ボタンを押して、ファイルの選択を確定します。 カットを中止するときは、[8▼](CANCEL)ボタンを押します。 タブ切替[ E][F]ボタンを押して、ファイルを貼り付けたい場所 (ユーザー /USB)を選びます。 [4▼](貼り付け)ボタンを押して、切
基本的な画面(メイン画面、選択画面)について 4 [7▼](OK)ボタンを押して、ファイル/フォルダーの選択を確定します。 削除を中止するときは、[8▼](CANCEL)ボタンを押します。 USB記憶装置のデータを一度に削 除する USB記憶装置をフォーマットすれ ば、USB記憶装置に入っているす べてのデータを一度に削除できます (26ページ)。 5 画面メッセージに従って、操作を進めます。 YES........................... 選んだファイル/フォルダーを削除します。 YES ALL.................. 選んだファイル/フォルダーすべてを一度に削除します。 NO ............................. 選んだファイル/フォルダーを削除せず、残します。 CANCEL ..................
基本的な画面(メイン画面、選択画面)について フォルダーを作る 新しいフォルダーを作ります。フォルダーには、ファイルを種類別に分けて入れること ができます。ファイル整理に活用しましょう。 1 2 3 「プリセット」画面にはフォルダー を作れません。 フォルダーを作りたい画面を表示させます。 [7▼](フォルダー )ボタンを押して、新しいフォルダーの名前を入力する画面を 表示させます。 「ユーザー」画面のフォルダーに ついて 「ユーザー」画面のフォルダー階層 は4階層までです。保存できるファ イルとフォルダーの総数は、ファイ ル名の長さにもよりますが、 最多で740 (CVP-405/403)、 370 (CVP-401)です。1つのフォ ルダーに保存できるファイルとフォ ルダーの総数は、最多で250です。 フォルダーの名前を入力します(下記参照)。 文字を入力する 基 本 操 作 ファイル/フォルダーに名前を付けたり、ミュージックファインダーやウェブページの キーワードを入力したりするときの、文字の入力方法をご説明します。携帯電話の文字 入力のような操作です。文字入力は、下記のような入力画
基本的な画面(メイン画面、選択画面)について 4 [8▲](OK)ボタンを押して、入力した文字列(名前/キーワードなど)を確定し ます。 ・文字を消す [データダイアル]で消したい文字にカーソルを移動させ、[7▼](DELETE)ボ タンを押します。入力した文字列を一度に消したいときは、[7▼](DELETE) ボタンを押し続けます。 ・濁点(゛)/半濁点(゜)を入力する 濁点/半濁点などを付けたい文字を入力し、文字を確定する前に[6▼]ボタン を押します。 ・記号を入力する 1 文字を確定したあとで[6▼]ボタンを押して、記号一覧を表示させます。 基 本 操 作 文字種が「かな漢」「カナ(半角)」以 外で濁点や半濁点が付かない文字の 場合は、文字入力確定前に[6▼]ボ タンを押しても記号一覧が表示され ます。 2 [データダイアル]で入力したい記号にカーソルを移動させ、[8▲](OK)ボ タンを押します。 ・数字を入力する 文字種のうち「ABC」(全角アルファベット)、 「ABC」「CASE」(半角アル ファベット大文字)「case」(半角アルファベット小文字)のどれかを選び、 [2▲▼]〜[5▲
設定を工場出荷時の状態に戻す 設定を工場出荷時の状態に戻す 設定を工場出荷時の状態に戻して も、インターネット機能の環境設定 (143ページ)は工場出荷時の状態に もどりません。 インターネット機能の環境設定を工 場出荷時の状態に戻すには、148 ページを参照してください。 システムを工場出荷時の状態に戻す いちばん右の鍵盤(C7)を押しながら電源をオンにします。 下記「設定別に工場出荷時の状態に戻す」の手順2で「SYSTEM SETUP(システム セットアップ)」を選んで工場出荷時の状態に戻すのと同じです。 設定別に工場出荷時の状態に戻す 1 設定画面を表示させます: MIDI セットアップ、ユーザーエ フェクト、ミュージックファイン ダー、ファイル&フォルダーでは、 編集によって作り上げたデータはす べて消去されますのでUSB記憶装 置に保存してください(172ページ)。 [ファンクション]→[J]UTILITY→タブ切替[ F]SYSTEM RESET 2 [1▲▼]〜[3▲▼]ボタンを押して、工場出荷時の状態に戻したい項目を選びま す。 SYSTEM SETUP (システムセットア
設定を工場出荷時の状態に戻す 4 [D]ボタンを押して、選んだ項目を工場出荷時の状態に戻します。 設定をひとつのファイルとして保存 / 呼び出しする 下記の項目については、 「ユーザー」/「USB」の画面に、設定をひとつのファイルとし て保存できます。必要に応じて、保存した設定を呼び出せます。 1 楽器の設定を、保存したい状態にします。 2 設定画面を表示させます: [ファンクション]→[J]UTILITY→タブ切替[F]SYSTEM RESET 基 本 操 作 3 [F]〜[I]ボタンを押して、設定を保存する画面を表示させます。 SYSTEM SETUP (システムセットアップ) MIDI SETUP (MIDIセットアップ) [ファンクション]→UTILITY画面やマイク設定画面(CVP-405/403) など、さまざまな画面での設定を1つのシステムセットアップファイ ルとして扱います。どの設定項目がシステムセットアップに該当する か、詳細は別冊データリストをご参照ください。 「ユーザー」画面上に保存したMIDIテンプレートファイル群を含む、 さまざまなMIDI設定を、1つのMI
USB 記憶装置の取り扱いについて USB 記憶装置の取り扱いについて この楽器には[USB TO DEVICE]端子が装備されています。 [USB TO DEVICE]端子に、USB対応の記憶装置(フラッシュメモリー、フロッピーディスクドライブ、ハードディスクドライブなど) を接続して、楽器本体で制作したデータをUSB記憶装置に保存したり、USB記憶装置のデータを楽器本体で再生したりできます。 USB記憶装置をご使用いただく場合は、以下のことをお守りください。 n USB記憶装置の取り扱いについては、USB記憶装置に付属の取扱説明書もご参照ください。 ■使用できるUSB記憶装置 • [USB TO DEVICE]端子に接続できるUSB記憶装置は、フ ラッシュメモリー、フロッピーディスクドライブ、ハード ディスクドライブ、CD-ROMドライブなどの2台までで す。(必要に応じてUSBハブを使用します。USBハブを使 用した場合でも楽器で一度に使用できるUSB記憶装置は2 台までです。)また、1台のUSB記憶装置について4ドライ ブまで認識ができます。その他の機器(マウス、コンピュー ターのキーボードなど
フロッピーディスクの取り扱いについて フロッピーディスクの取り扱いについて フロッピーディスクドライブは別売品(182ページ)をご使用ください。 ディスク挿入口にフロッピーディスクを挿入すると、本体で作ったデータをディスクに保存したり、 ディスク内のデータを本体に読み 込んだりできます。 フロッピーディスクをご使用いただく場合は、以下のことをお守りください。 ■使用できるフロッピーディスクの種類 ■磁気ヘッドの定期的なクリーニング • ディスクドライブユニットは高精度の磁気ヘッドを使用し • 3.
本 編 ボイスの設定/編集をする 別冊クイックガイドの目次 いろいろな楽器音(ボイス)を使って演奏してみましょう........................... 8ページ ピアノの音で演奏してみましょう .............................................................8ページ ボイス(楽器音)を変えて弾いてみましょう ...........................................11ページ ボイス名の上の表示について 本 編 内蔵のボイス名の上には、ボイスの特長が表示されます。 Natural! (ナチュラル) 鍵盤楽器を中心とした鍵盤演奏に適したボイスです。 ステレオサンプリング、 ダイナミックサンプリング(CVP-405/403)、サステインサンプリング (CVP-405/403)、キーオフサンプリング(CVP-405/403)などの技術も 使われています。 S.
いくつかのボイスを同時に鳴らす いくつかのボイスを同時に鳴らす 本体の鍵盤では、複数のボイスを重ねて鳴らしたり、左手鍵域と右手鍵域に分けて違う ボイスを鳴らすといった、アコースティックの鍵盤楽器にはない、特殊な使い方ができ ます。 鍵盤パート(右手1、右手2、左手)について ボイスには、右手1、右手2、左手の3つの鍵盤パートがあります。鍵盤パートオン/オ フボタンでこの3つのパートを組み合わせて同時に鳴らすことにより、厚みのある演奏 ができます。 鍵盤パートの組み合わせ 各パートの音量バランスを調節する 音量バランスを調節する画面(別冊 クイックガイド20ページ)で、各 パートの音量バランスを調節しま す。 パート表示: RIGHT1 ...... 右手1 RIGHT2 ...... 右手2 LEFT............
いくつかのボイスを同時に鳴らす ■ デュアル+スプリット: 鍵域を左右に分けて別々のボイスで弾く+右の鍵域で2つのボ イスを重ねて鳴らす (右手1パート+右手2パート+左手パート) 上記3つのパートを同時に鳴らすことにより、厚みのある演奏ができます。 左手パート 右手2パート 右手1パート 2つのボイスを重ねて鳴らす 2つのボイスを重ねるときは、デュアル機能をオンにして右手1パートに右手2パートを 重ねます。 1 鍵盤パートオン/オフ[デュアル(右手2)]ボタンを押して、右手1パートに右手2 パートを重ねます。 2 3 ボイスボタンの1つを押してボイスカテゴリーを選ぶと、右手2パートのボイス 選択画面が表示されます。 ボ イ ス の 設 定 / 編 集 を す る ボイスボタンだけで右手1、右手2 パートのボイスを選ぶ パネルのボイスボタンを使って、右 手1パートと右手2パートのボイス をすばやく設定できます。ボイスボ タンの1つを押しながら、別のボイ スボタンを押すと、最初に押したボ タンに対応したボイスが右手1パー トに、あとに押したボタンに対応し たボイスが右手2パートに設定され
いくつかのボイスを同時に鳴らす デュアル機能をペダルでオン/オフ する 鍵盤パートオン/オフ[デュアル(右 手2)]の機能をペダルに割り当てれ ば、デュアル機能をペダルでオン/ オフできます(152ページ)。 両手で演奏中にデュアル機能をオン /オフしたいときに便利です。 5 鍵盤を弾いてみましょう。 6 デュアル機能をオフにするときは、もう一度鍵盤パートオン/オフ[デュアル(右 手2)]ボタンを押します。 鍵域を左右に分けて別々のボイスで弾く 鍵域を左右に分けて別々の音色で弾くときは、スプリット機能をオンにして右手1パー トと左手パートを同時に鳴らします。 1 ボ イ ス の 設 定 / 編 集 を す る 2 3 鍵盤パートオン/オフ[スプリット(左手)]ボタンを押して、右手1パートと左手 パートを同時に鳴らします。 ボイスボタンの1つを押してボイスカテゴリーを選ぶと、左手パートのボイス選 択画面が表示されます。 タブ切替[E]ボタンを押して、 「プリセット」タブを選びます。 3 4 スプリット機能をペダルでオン/オフ する 鍵盤パートオン/オフ[スプリット (左手)]の機
音の高さに関する設定 音の高さに関する設定 移調(トランスポーズ)する 鍵盤の音やソングを、半音単位で移調できます。 ・ 演奏中に移調する トランスポーズ[-]/[+]ボタンを押して、移調します。 ・ 演奏前に移調しておく ミキサー画面で移調します。鍵盤演奏音(KBD)、ソング再生音(SONG)、本体が発音 するすべてのサウンド(MASTER)それぞれについて移調できます。 1 設定画面を表示させます: [ミキサー ]→タブ切替[E][F]TUNE 2 [1▲▼]〜[3▲▼]ボタンを押して、移調します。 ボ イ ス の 設 定 / 編 集 を す る 鍵盤全体のピッチを微調整する 鍵盤全体のピッチを微調整(チューニング)します。合奏のときや、CDの再生に合わせて 演奏するときなど、ほかの楽器やCDの再生音などと音の高さを正確に合わせることが ドラム/SFXキットボイスはチュー ニングできません。 できます。 1 設定画面を表示させます: [ファンクション]→[A]MASTER TUNE/SCALE TUNE→ タブ切替[ E]MASTER TUNE 2 Hz(ヘルツ)とは 音の高さ(1秒間に
音の高さに関する設定 4 必要に応じて、下記の操作をします。 ・ ノート(鍵盤)ごとにチューニングする(TUNE) 1 [3▲▼]ボタンを押して、ノートを選びます。 2 [4▲▼]/[5▲▼]ボタンを押して、選んだノートを1セント単位でチューニ セントとは 半音を100等分した音程の単位で す。(100セント=半音) 選んだ音律をワンタッチで呼び出し たいときは レジストレーションメモリーに登録 します。レジストレーション登録項 目の「SCALE」にチェックマークを 付けて登録しましょう(89ページ)。 ボ イ ス の 設 定 / 編 集 を す る ングします。 ・ 音律の基準となる音(ベース音)を変える(BASE NOTE) [2▲▼]ボタンを押して、ベース音を選びます。 ベース音を変えると、音律の音程を保ったまま移調します。 内蔵の音律 EQUAL TEMPERAMENT (イコールテンペラメント=平均律) 1オクターブを12の間隔で等分した音律です。現在 もっともポピュラーな、ピアノの調律法です。 PURE MAJOR(ピュアメジャー =純正律長調) PURE MINOR(ピュアマイナー
ボイスにエフェクト ( 効果 ) をかける ボイスにエフェクト(効果)をかける 本体には、鍵盤での演奏音に深さや広がりを付け表現の幅を広げる、いろいろな種類の エフェクトが用意されています。 1 メイン画面を表示させます: [ダイレクトアクセス]→[戻る] 2 CVP-405/403では[A]〜[C]/[F]〜[H]、CVP-401では[A]/[B]/[F]〜[I]を 押して、エフェクトをかける鍵盤パートを選びます。 3 4 ボ イ ス の 設 定 / 編 集 を す る [ボイスエフェクト]ボタンを押して、設定画面を表示させます。 画面下の[1▲▼]/[3▲▼]〜[5▲▼] / [I] (HARMONY/ECHO)ボタンを押し て、エフェクトをかけます。 CVP-405/403/401 取扱説明書 43
ボイスにエフェクト ( 効果 ) をかける エフェクトの種類 ハーモニー /エコーはペダルでオン /オフできます(152ページ)。 ポルタメントとは 高さの異なる複数の音をなめらかに ピッチ変化させることです。 ポルタメントのピッチ変化にかかる 時間(ポルタメントタイム)は、ミキ サー画面で調節できます(48ページ)。 DSPとは デジタルシグナルプロセッサー (Digital Signal Processor)の略 で、デジタル信号を加工してさまざ まなエフェクトを作り出す専用マイ クロプロセッサーのことです。 ボ イ ス の 設 定 / 編 集 を す る LEFT HOLD (レフトホールド) HARMONY/ECHO (ハーモニー /エコー ) 鍵盤から指を離しても、左手パートのボイスを鳴らしたままにすること ができます。ストリングのように減衰しないボイスを鳴り続けるように したり、ピアノのように減衰するボイスをより遅く減衰するように(サス テインペダルを踏んだように)することができます。 右手鍵域で弾いた演奏にハーモニーやエコーの効果を付けます。 (44ページ) MONO/POLY (
ボイスにエフェクト ( 効果 ) をかける ● ハーモニータイプ 44ページで選択したハーモニータイプ、および下図のハーモニー用コード検出域で 押鍵されたコードに従って、右手鍵域での演奏音にハーモニーが付加されます。 スプリットポイント スプリットポイント スタイル再生およびハーモニー用コード鍵域 スプリットポイント (スタイル用) スタイル再生お よびハーモニー 用コード鍵域 ハーモニー用コード鍵域でコード音 を鳴らさないようにする [スタイルオン/オフ]をオン、[シン クロスタート]をオフにし、ストッ プアカンパニメント(65ページ)で 「OFF」を選びます。 ボイス左手および ハーモニー用コード 鍵域 ボイス右手1, 2 スプリットポイント (ボイス用) ボイス左手 ボ イ ス の 設 定 / 編 集 を す る ボイス右手1, 2 ● マルチアサインタイプ スタイルのオン/オフや左手パートのオン/オフに関係なく、右手鍵域でのコード押鍵 の各音に対して個別の鍵盤パートボイスをアサインする(割り当てる)機能です。鍵盤 パートの右手1と右手2をオンにして使います。弾いた順番にボイ
音量バランスや音色などを調節する ( ミキサー ) 音量バランスや音色などを調節する (ミキサー ) ミキサーとは 複数の音声信号をまとめて、音声バラ ンスやステレオ定位、エフェクトのか かり具合などを調節する装置です。 内蔵のミキサーを使って、鍵盤パート間やソング/スタイルチャンネルごとに、音量バ ランスを取ったり音色を調節したりできます。 基本操作 1 [ミキサー ]ボタンを押して、ミキサー画面を表示させます。 2 ボ イ ス の 設 定 / 編 集 を す る 4 1, 3 2 4 5 タブ切替[E][F]ボタンを押して、設定画面を表示させます。 設定できる内容については、 「ミキサー画面で設定できる項目」(47ページ)を参 照してください。 パートについて 47ページを参照してください。 3 [ミキサー ]ボタンを繰り返し押して、パートを選びます。 ミキサー画面は、パート別に分かれています。パート名は、画面上部に表示され ます。パートが切り替わる順番は、下記のとおりです。 全パート(PANEL PART)→スタイルパート(STYLE PART)→ソングチャンネ ル1〜8
音量バランスや音色などを調節する ( ミキサー ) ・ SONG CH 1〜8/9〜16(ソングチャンネル1〜8/9〜16)の設定 ソングデータの一部として記憶(セットアップ)させてから、ソングを保存しま す。セットアップ画面(122ページ)を参照してください。 ミキサーのパートについて PANEL PART(パネルパート) 鍵盤パートやマイク入力音(CVP-405/403)、ソング、スタイルの設定ができ ます。バランスを設定する画面に表示されるパートと同じです(別冊クイックガ イド20ページ) 。 STYLE PART(スタイルパート) スタイルパートは、8つのチャンネルで構成されています。ここでは、スタイル パートのチャンネルごとの設定ができます。8つのチャンネルは、[チャンネルオ ン/オフ]ボタン(12ページ)を押して「スタイル」を表示させたときのチャンネル ボ イ ス の 設 定 / 編 集 を す る と同じです。 SONG CH 1〜8/9〜16(ソングチャンネル 1〜8/9〜16) ソングは、16のチャンネルで構成されています。ここでは、ソングのチャンネ ルごとの設定ができます。16のチ
音量バランスや音色などを調節する ( ミキサー ) TUNE (チューン) ボ イ ス の 設 定 / 編 集 を す る PORTAMENTO TIME (ポルタメントタイム) ポルタメントとは、最初に弾いた鍵盤のピッチから次に弾いた鍵盤の ピッチまでを、連続的に変化させる機能です。ここでは、ポルタメント のピッチ変化にかかる時間を設定します。値を大きくするほどピッチの 変化にかかる時間が長くなります。0の場合は効果がありません。ポル タメントタイムは、モノ(56ページ)に設定されている鍵盤パートに対 して有効です。 PITCH BEND RANGE (ピッチベンドレンジ) ペダルにピッチベンドやグライドを割り当てたときに( 152ページ)ピッ チがどれだけ変化するかを、半音単位で、鍵盤パートごとに設定できま す。 OCTAVE (オクターブ) 鍵盤演奏でのオクターブを、鍵盤パートごとに設定できます。 TUNING (チューニング) 鍵盤演奏でのチューニングを、鍵盤演奏パートごとに変えることができ ます。 TRANSPOSE (トランスポーズ) トランスポーズ設定を、本体で鳴るサウン
音量バランスや音色などを調節する ( ミキサー ) 5 [ 1▲▼]〜[3▲ ▼]ボタン を押して、リ ボイスの対 象としたいXGボイスを 選び ま す。 5 6 6 7 ボ イ ス の 設 定 / 編 集 を す る [4▲▼]〜[6▲▼]ボタンを押して、手順5で選んだXGボイスをクラビノーバの どのボイスに差し替えるか決めます。 どのボイスに差し替えるか迷う場合は、[F]/[G]/[I]ボタンを押しておすすめのボ イスに差し替えます。 ALL REVOICE: 差し替えできるすべてのXGボイスを、クラビノーバの PIANO REVOICE: ボイスに差し替えます。 ピアノボイスだけを差し替えます。 BASIC REVOICE: ソング再生に適したボイスだけを差し替えます。 ALL NO REVOICE: すべてのXGボイスを、元のXGボイスに戻します。 7 8 [8▲](OK)ボタンを押して、確定します。 中止するときは、[8▼](CANCEL)ボタンを押します。 「VOL/VOICE」画面で[F]ボタンを押して、ソングオートリボイスをオンにします。 エフェクトタイプ ■
音量バランスや音色などを調節する ( ミキサー ) DSPとは デジタル シグナル プロセッサー (Digital Signal Processor)の略 で、デジタル信号を加工してさまざ まな効果(エフェクト)を作り出す専 用マイクロプロセッサーのことで す。 5 [1▲▼]/[2▲▼]ボタンを押して、エフェクトブロックを選びます。 5 ボ イ ス の 設 定 / 編 集 を す る 6 7 8 エフェクトブロック 対象パート エフェクトの特徴 REVERB (リバーブ) 全パート コンサートホールやライブハウスで演奏して いるような臨場感を得ることができます。 CHORUS (コーラス) 全パート 同時に複数のパートを演奏しているような厚 みを得ることができます。 DSP1 スタイルパート ソングチャンネル1〜16 リバーブとコーラスに加え、ディストーショ ンのように音を歪ませる効果をはじめとする いろいろな効果をかけることができます。 DSP2 DSP3 RIGHT1(右手1) RIGHT2(右手2) LEFT(左手) ソングチャンネル1〜16 未使用のDS
音量バランスや音色などを調節する ( ミキサー ) ■ エフェクトを調節/保存する 9 [F](PARAMETER)ボタンを押して、エフェクトタイプ調節画面を表示させます。 10 手順5で、DSP2〜4を選んだ場合 ボイス設定の「VARIATION(バリエーション)」オン/オフ(59ページ)それぞれ について、エフェクトタイプを調節できます。 バリエーションオフの場合のエフェクトタイプを選ぶには、[B]ボタンを押しま エフェクトブロック/エフェクトタ イプのカテゴリー /エフェクトタイ プを選び直す [1▲▼]〜[3▲▼]ボタンを押しま す。選んだ設定は、画面左上に表示 されます。 ボ イ ス の 設 定 / 編 集 を す る す。バリエーションオンの場合の項目を選ぶには、[E]ボタンを押します。 10 13 11 11 12 [4▲▼]/[5▲▼]ボタンを押して、調節したい項目を選びます。 ここで調節できる項目は、エフェクトタイプによって異なります 12 [6▲▼]/[7▲▼]ボタンを押して、手順11で選んだ項目の値を調節します。 手順5で、REVERB、CHORUS、DS
音量バランスや音色などを調節する ( ミキサー ) 14 [3▲▼]〜[6▲▼]ボタンを押して、エフェクトタイプの保存先を選びます。 エフェクトブロックにより保存できる数が違います 15 ボ イ ス の 設 定 / 編 集 を す る 14 15 [I](SAVE)ボタンを押して、保存します(27ページ)。 保存したエフェクトを呼び出すときは、手順8と同じ操作をします。 イコライザー イコライザー (EQ)とは、音をいくつかの周波数帯域(バンド)に分けて、各帯域のレベル (ゲイン)を上げ/下げ(ブースト/カット)することで、サウンドを補正する装置のことで す。通常、イコライザーはアンプやスピーカーから出力されるサウンドを、部屋の特性 に合わせて音質補正するために使われます。たとえば、ステージや大きなスタジオな ど、うなるようなサウンドの環境では、低周波数帯をカットしてすっきりとしたサウン ドに変えることができます。また、部屋や閉じられた空間などで響きがなかったり、ラ ンダムに音が跳ね返るような場所では、高周波数帯を持ち上げてはっきりしたサウンド を作ることができます。本体には、高性能の5バンド
音量バランスや音色などを調節する ( ミキサー ) ■ イコライザータイプを選ぶ 1〜3 4 46ページの基本操作と同じです。手順2では、「EQ」タブを選びます。 [A]/[B]ボタンを押して、演奏する場所などに合ったイコライザータイプを選び ます。 選んだイコライザーを調節する場合は、次の手順に進んでください。 ■ 選んだイコライザーを編集/保存する 5 [F](EDIT)ボタンを押して、編集画面を表示させます。 ボ イ ス の 設 定 / 編 集 を す る 6 [A]/[B]ボタンを押して、イコライザータイプを選びます。 6 9 8 7 7 [3▲▼]〜[7▲▼]ボタンを押して、各帯域でのゲインを調節します。 すべての帯域のゲインを同時に調節するには、[8▲▼]ボタンを押します。 CVP-405/403/401 取扱説明書 53
音量バランスや音色などを調節する ( ミキサー ) 8 手順7で選んだ帯域の幅/中心周波数を調節します。 ・ 帯域の幅(Q)を調節する [1▲▼]ボタンを押します。値を高くするほど、帯域の幅は狭くなります。 ・ 帯域の中心周波数(FREQ)を調節する [2▲▼ ]ボタンを押 します。 有効な 中心周波 数の幅は 、帯域 によって 異なり ま す。 9 [H]/[I](STORE1/2)ボタンを押して、編集したイコライザーを保存します(27 ページ)。 2種類のイコライザーを保存できます。保存したイコライザーを呼び出すとき は、手順6と同じ操作をします。 ボ イ ス の 設 定 / 編 集 を す る 54 CVP-405/403/401 取扱説明書
オリジナルのボイスを作る ( ボイス編集 ) オリジナルのボイスを作る(ボイス編集) ボイス編集の機能を使うと、既存のボイスを編集し、オリジナルのボイスを作れます。 作ったボイスをユーザーボイスとして保存すれば、必要なときに呼び出して使えます。 オルガンフルートボイスとそれ以外のボイスとでは、編集方法が異なります。 基本操作 1 オルガンフルートボイスを編集する オルガンフルートボイスは、編集方 法が異なります。オルガンフルート ボイスの編集方法については、59 ページを参照してください。 基になるボイス(オルガンフルート以外のボイス)を選びます(別冊クイックガイ ド11ページ)。 2 [6▲](ボイスセット)ボタンを押して、ボイス編集画面を表示させます。 ボ イ ス の 設 定 / 編 集 を す る 3 タブ切替[ E][F]ボタンを押して、設定画面を表示させます。 設定できる内容については、「ボイス編集画面で設定できる項目」(56ページ)を 参照してください。 3 4 7 6 5 4 必要に応じて[A]/[B]ボタンを押して、設定項目を選びます。 CVP-405/403/
オリジナルのボイスを作る ( ボイス編集 ) ほかのボイスボタンを押すことによ り、ここでの設定を保存せずにほか のボイスに切り替えられます。ここ での設定を保存しておきたい場合は、 ほかのボイスに切り替える前に、必 ずユーザーボイスとして保存してく ださい。 選んだボイスによって、設定できる 項目は異なります。 5 [1▲▼]〜[8▲▼]ボタンを押して、ボイスを編集します。 6 [D](COMPARE)ボタンを押して、編集前のボイスと編集後のボイスを聞き比べ ます。 7 [I](SAVE)ボタンを押して、保存します(27ページ)。 ボイス編集画面で設定できる項目 55ページ手順3の画面で設定できる項目は以下のとおりです。5種類の設定画面ごとに説明し ます。これらの項目はボイスセット(61ページ)に含まれ、ボイスを選ぶと自動的に設定され ます。 PIANO(ピアノ) この画面は、Natural! (37ページ)のピアノ音を選んでいるときに表示されます。 タッチセンスによるベロシティー カーブの変化 ボ イ ス の 設 定 / 編 集 を す る TUNING CURVE (チューニング
オリジナルのボイスを作る ( ボイス編集 ) CONTROLLER(コントローラー ) 1.
オリジナルのボイスを作る ( ボイス編集 ) ● EG (エンベロープジェネレーター ) EG (エンベロープジェネレーター )により、時間経過の中でどのように音量が変化して いくかを設定できます。これにより、 「音の立ち上がりや減衰が早い」(パーカッション など)や、 「余韻が長い」(ピアノなど)といった生楽器が持つさまざまな音の特性を作り 出すことができます。 ATTACK (アタック) 鍵盤を押さえたとき、0から最大の出力レベルに達するまでの時間を設定しま す。値を小さくするほど、音の立ち上がりが早くなります。 DECAY (ディケイ) 最大の出力レベルから減衰してサステインレベル(鍵盤を押さえている間持続す る一定のレベル)に達するまでの時間を設定します。値を小さくするほど、音が 速く減衰します。 RELEASE (リリース) 鍵盤を離したあと、出力レベルが0に達するまでの時間を設定します。値を小 さくするほど、音が速く消えます。 レベル サステインレベル ボ イ ス の 設 定 / 編 集 を す る ATTACK DECAY RELEASE 鍵盤を弾く 時間 鍵盤を離
オリジナルのボイスを作る ( ボイス編集 ) 2. DSP DSP TYPE (DSPタイプ) DSPエフェクトのタイプを選びます。CATEGORY(カテゴリー )を選 んでからTYPE(タイプ)を選びます。 VARIATION (バリエーション) 各DSPエフェクトタイプには、2つのバリエーションがあります。 ここでは、DSPエフェクトタイプのバリエーションを編集できます。 ON/OFF (オン/オフ) 初期設定では、2つのバリエーションのうち、ボイスに最適なバリ エーションが割り当てられています(オフの状態)。オンを選ぶと、 もう一方のバリエーションを割り当てることができます。オンにし て割り当てたバリエーションは、下記「バリュー」で効果の深さも 変えられます。 PARAMETER(パラメーター ) DSPエフェクトタイプのバリエーション名が表示されます。 VALUE(バリュー ) バリエーションがオンの場合の、効果の深さを設定します。 3.
オリジナルのボイスを作る ( ボイス編集 ) 3 タブ切替[E][F]ボタンを押して、設定画面を表示させます。 設定できる内容については、次の「オルガンフルートボイス編集画面で設定でき る項目」を参照してください。 3 4 EFFECT/EQタブを 選んだ場合は、 [A]/[B]ボタン を押して設定項目 を選ぶ 6 5 ボ イ ス の 設 定 / 編 集 を す る 4 手順3で「EFFECT/EQ」タブを選んだ場合は、[A]/[B]ボタンを押して、設定 項目を選びます。 ほかのボイスボタンを押すことによ り、ここでの設定を保存せずにほか のボイスに切り替えられます。ここ での設定を保存しておきたい場合 は、ほかのボイスに切り替える前 に、必ずユーザーボイスとして保存 してください。 5 [A]〜[D]/[F]〜[H]/[1▲▼]〜[8▲▼]ボタンを押して、ボイスを編集します。 6 [I](SAVE)ボタンを押して、保存します(27ページ)。 オルガンフルートボイス編集画面で設定できる項目 59ページ手順3の画面で設定できる項目は以下のとおりです。3種類の設定画面ごとに 説明します。
オリジナルのボイスを作る ( ボイス編集 ) 16'〜1' (フッテージ) フッテージの設定により、オルガンフルートの基本音色が決まります。 パイプが長いほど、ピッチが低くなります。 「16'」は最も低いピッチ 成分を決定し、 「1'」は最も高いピッチ成分を決定します。設定値が高 いほど、対応するフッテージの音量が大きくなります。さまざまな音量 のフッテージを組み合わせて、独特なオルガンサウンドを作り出すこと ができます。 VOLUME/ATTACK(ボリューム/アタック) VOL (ボリューム) オルガンフルート全体の音量を調節します。バー表示が長いほど音量が 大きくなります。 RESP (レスポンス) 音のアタックとリリース(58ページ)との両方を調節します。フッテー ジコントロールに対して、音の鳴り始めの増減部分の反応時間を調節し ます。値を高くするほど音の反応が遅くなります。 VIBRATO SPEED (ビブラートスピード) Vibrato On/OffとVibrato Depth(60ページ)によってコントロールさ れるビブラート効果の、スピードを決定します。 MODE (モード
スタイルの設定/制作をする 別冊クイックガイドの目次 スタイルを使って「メリーさんのひつじ」を演奏してみましょう ......... 24ページ スタイル再生に変化を付ける................................................................. 27ページ コードの押さえ方を確かめる................................................................. 29ページ 選んだスタイルに最適なボイスなどを呼び出す (ワンタッチセッティング=OTS) .........................................................
リズムだけを鳴らす SINGLE FINGER (シングルフィンガー ) 1〜3本の指で簡単にコードを指定できる方法で、スタイル再生に対して だけ有効です。 C ◆メジャー (M) コード ルートキーを押さえてください。 Cm ◆マイナー (m) コード ルートキーと、ルートキーより左側の黒鍵を同時に押さえてください。 C7 ◆セブンス (7) コード ルートキーと、ルートキーより左側の白鍵を同時に押さえてください。 Cm 7 ◆マイナーセブンス (m7) コード ルートキーと、ルートキーより左側の黒鍵と白鍵を同時に押さえてく ださい。 MULTI FINGER (マルチフィンガー ) 「シングルフィンガー」の押鍵ルールと「フィンガード」の押鍵ルールの 両方が使えます。 FINGERED (フィンガード) コードを構成する音をそのまま押すことによって、コードを指定する方法 です。詳細は別冊データリストをご覧いただくか、コードチューター機能 (別冊クイックガイド29ページ)で調べることができます。 FINGERED ON BASS (フィンガードオンベース ) フィンガードで認識されるコ
リズムだけを鳴らす スタイルをチャンネルごとにオン / オフする スタイルは、RHY1(リズム1)〜PHR2(フレーズ2)の8つのチャンネルで構成さ れています。スタイルを再生させながら各チャンネルをオン/オフして、スタイ ルの雰囲気を変えてみましょう。 1 [チャンネル オン/オフ]ボタンを押して、スタイルチャンネルをオン/オフす る画面を表示させます。 「スタイル」タブが選ばれていないときは、もう一度[チャンネル オン/オフ] ボタンを押します。 2 [1▼]〜[8▼]ボタンを押して、各チャンネルをオン/オフします。 1チャンネルだけ再生するときは、再生したいチャンネルのボタンを押し続 けて「SOLO(ソロ)」にします。ソロを解除するには、もう一度ソロチャン ネルのボタンを押します。 ス タ イ ル の 設 定 / 制 作 を す る フリーテンポで(スタイルを再生せずに)コード音を鳴らす [スタイルオン/オフ]をオン、[シンクロスタート]をオフにすると、スタイルを再 生せずにコード音を鳴らせます。たとえば、フィンガリングで「MULTI FINGER (マルチフィンガー )」を選んでいれば(6
スタイル再生に関する設定 スタイル再生に関する設定 ここでは、スタイル再生に関するさまざまな設定方法を説明します。 下図の手順で呼び出される画面上で、スタイル再生に関する各種設定が行なえます。 1 設定画面を表示させます: [ファンクション]→[C]STYLE SETTING/SPLIT POINT/CHORD FINGERING→タブ切替[ E]STYLE SETTING 2 [ 1▲▼] 〜[8▲▼]ボタンを押して各種設定をします。 ス タ イ ル の 設 定 / 制 作 を す る ・ ストップアカンパニメント(STOP ACMP) [スタイルオン/オフ]がオン、[シンクロスタート]がオフで、スタイルを再生させてい ない状態をいいます。この状態で左手コード鍵域でコードを押さえると、押さえた コードのルート/タイプがメイン画面に表示され、本体上にコードとして認識されま す。 ストップアカンパニメントの状態で左手コード鍵域を押さえたときに、コード音(スタ イルのパッドとベースチャンネル)をどのように鳴らすかを決めます。 OFF(オフ)..............................
スタイル再生に関する設定 ・ シンクロストップウィンドウ(SYNCHRO STOP WINDOW) シンクロストップがオンに設定されていても、ある指定した時間より長くコード鍵域 を押し続けた場合は、シンクロストップを機能させなくすることができます。ここで OFF(オフ)以外の値(音符)を設定した場合、音符に該当する時間より長くコード鍵域 を押さえ続けると、コード鍵域から指を離してもシンクロストップは機能せず、スタ イルは再生を続けます。つまり、シンクロストップは指定した音符の長さより短い時 間で鍵盤から指を離したときに機能します。 ・ スタイルタッチ(STYLE TOUCH) コード鍵域での鍵盤にタッチレスポンスを付けることができます。オンに設定すると、 コード鍵域を押した強さで自動伴奏(スタイル再生)の音量を変えることができます。 ・ スタイルチェンジビヘイビヤー (STYLE CHANGE BEHAVIOR) 下記3種類があります。 ・ セクションセット(SECTION SET) スタイル再生がストップしている状態でスタイルを変更したときの、選択さ れるセクション(イントロやメインなど)を決めます。OF
スプリットポイントの設定 スプリットポイントの設定 鍵盤の機能を左右で分割するポイントをスプリットポイントといい、鍵盤位置(ノート ネーム)で指定します。 1 設定画面を表示させます: [ファンクション]→[C] STYLE SETTING/SPLIT POINT/CHORD FINGERING→タブ切替[ E][F] SPLIT POINT 2 [F]〜[H]ボタンを押してスプリットポイントの設定(下記参照)をします。 スプリットポイントには、下記2種類があります。 ス タ イ ル の 設 定 / 制 作 を す る ・ ボイス演奏用の鍵域と、自動伴奏(スタイル再生機能)用のコード鍵域とのスプリッ トポイント(S) ・ 右手用ボイス(右手1、2)の鍵域と左手用ボイスの鍵域とのスプリットポイント(L) この2つは初期設定では同じ鍵盤位置(ノートネーム)になっていますが、違う位置に 設定することも可能です。 スプリットポイント(S)とスプリットポイント(L)を同じ位置に設定する方法 [F](S+L)ボタンを押してから[データダイアル]を回します。 スプリットポイント(S+L) 右手用ボイス(右
スタイルの音量バランスや音色などを調節する ( ミキサー ) スタイルの音量バランスや音色などを調節 する ( ミキサー ) スタイルに含まれるボイスについて「ミキサー画面で設定できる項目」(47ページ)の設 定ができます。操作は、 「音量バランスや音色などを調節する(ミキサー )」(46ページ) の基本操作の手順3で「STYLE PART」を表示させ、手順に従います。 ミュージックファインダーの便利な使い方 ミュージックファインダーとは、弾きたい曲に合ったパネル設定(ボイスやスタイルなど )を呼び出す機能です(別冊クイックガイド31ページ)。 ミュージックファインダーのレコードは、検索や編集ができます。 レコードを検索する ミュージッ クファインダ ーの検索機能 を使って、 曲名やキーワ ードからレ コードを探 すことがで きます。検索 したレコード は、 「 FAVORITE(フェーバリ ット=お気に入 り) 」 画面に追加で きます。 1 ス タ イ ル の 設 定 / 制 作 を す る 2 3 68 CVP-405/403/401 取扱説明書 [ミュージックファインダー ]ボタンを
ミュージックファインダーの便利な使い方 4 検索の条件を入力します。 入力した条件を消去する 曲名/キーワード/スタイル名を消去 するときは、[F]/[G]/[H](CLEAR) ボタンを押します。 ・ 曲名/キーワードで検索する 1 2 [A](MUSIC=曲名)/[B](KEYWORD=キーワード)ボタンを押して、文字 入力画面を表示させます。 曲名/キーワードを入力します(31ページ)。 複数のキーワードを入力する 複数のキーワードを入力するには、 カンマ(,)で区切って入力します。 ・ スタイル名で検索する 1 2 3 [C](STYLE=スタイル名)ボタンを押して、スタイル選択画面を表示させ ス タ イ ル の 設 定 / 制 作 を す る ます。 [A]〜[J]ボタンを押して、スタイルを選びます。 [戻る]ボタンを押して、検索画面に戻ります。 ・ その他の条件を追加する 曲名/キーワード/スタイル名に加えて、下記の条件を追加できます。 拍子(BEAT) .............................................
ミュージックファインダーの便利な使い方 5 [8▲](START SEARCH)ボタンを押して、検索をスタートします。 検索をスタートすると自動的にSEARCH 1画面に切り替わり、検索結果が表示 されます。検索を中止するときは、[8▼](CANCEL)ボタンを押します。 別の音楽ジャンルを検索する 別の音楽ジャンルを検索したい場合は、ミュージックファインダー画面で[6▼] (SEARCH 2)ボタンを押して検索します。検索した結果は「SEARCH 2」画面 に表示されます。 スタイルに合ったパネル設定を呼び出す ( レパートリー ) スタイル名から検索する場合、レパートリー機能を使って検索しても同じ検索結 果を得られます。詳細は別冊クイックガイド(32ページ)をご覧ください。 お気に入りのレコードを簡単に呼び出す ス タ イ ル の 設 定 / 制 作 を す る たくさんのレコードの中からサーチ機能などを使って探し出したレコードを、 「FAVORITE(フェーバリット=お気に入り)」画面に入れておくことで、あとからすぐに 呼び出すことができます。 1 2 3 ミュージックファインダー画
ミュージックファインダーの便利な使い方 レコードを編集する 現在選ばれているレコードを編集して、新しいレコードを作ることができます。新しく 追加作成されたレコードは楽器本体のメモリーに自動的に保存されます。 1 ミュージックファインダー画面で、編集元のレコードを選びます。 2 [8▲▼](RECORD EDIT)ボタンを押して、編集画面を表示させます。 3 レコードを編集します。 内蔵のレコードも、変更/削除でき ます。変更/削除しない(編集元のレ コードをそのまま残したい)ときに は、編集したあとで新しいレコード としてミュージックファインダーに 追加登録(72ページ手順5)して ください。 ス タ イ ル の 設 定 / 制 作 を す る ・ 曲名/キーワード/スタイル名を編集する 検索画面の場合と同じ方法(68ページ)で、各項目を入力します。 ・ テンポを変える [1▲▼](TEMPO)ボタンを押します。 ・ セクション(イントロ/メイン/エンディング)を記憶させる [2▲▼]/[4▲▼]ボタンを押して、レコードを選んだときに自動的に設定され るセクションを選びます。イントロ(IN
ミュージックファインダーの便利な使い方 5 編集したレコードを追加/上書きします。 ・ 新規レコードとして追加する [J](NEW RECORD)ボタンを押します。レコードは、「ALL」画面に追加さ れます。手順4で「FAVORITE」をオンにした場合は、レコードが、「ALL」 ミュージックファインダーに登録で きるレコード数は、内蔵レコードも 含めて全部で2500個(CVP-405/ 403)、1200個(CVP-401)です。 画面と「FAVORITE」画面の両方に追加されます。 ・ 編集元のレコードを上書きする [8▲](OK)ボタンを押します。手順4で「FAVORITE」をオンにした場合は、 レコードが「FAVORITE」画面にも追加されます。「FAVORITE」画面のレ コードを編集した場合は、そのレコードが上書きされます。 レコードを保存する ミュージックファインダーでは、本体上のメモリーにある、内蔵レコードまたは新しく 追加されたレコードすべてが1つのファイルとして保存されます。個別のレコード(パネ ル設定)がファイルではないことにご注意ください。 1 ス タ イ ル の 設 定 /
ミュージックファインダーの便利な使い方 「ユーザー」/「USB」などに保存されているミュージックファインダー を呼び出す 「ユーザー」/「USB」などに保存されているミュージックファインダーを呼び 出す方法は、下記のとおりです。 1 「MUSIC FINDER」画面を表示させます : [ミュージックファインダー ]→タブ切替[E][F]ALL 2 [7▲▼](FILES)ボタンを押して、ミュージックファインダーのファイル選択 画面を表示させます。 3 タ ブ切替[ E][F] ボタンを押 して、 「 ユーザー」 /「USB」など を選びま す。 4 [ A]〜[ J]ボ タンを 押し て、ミ ュージ ックフ ァイ ンダー のファ イルを 選び ま す。 ファイルを選ぶと、ファイルの内容に応じてメッセージが表示されますので、 目的のボタンを押してください。 ・ REPLACE(リプレース) 現在のミュージックファインダー全レコードが消去され、ファイルから呼び 出されたレコードに置き替えられます。 ミュージックファインダーは1つの ファイルの中にすべてのレコードを 含んでいますので、操作の仕方に よっては大事
スタイルを制作する ( スタイルクリエーター ) レコードに関する情報をウェブで表示させましょう (ミュージックファインダープラス) 右記のサービス内容は、変更するこ とがあります。 ミュージックファインダーで気になったレコードに関する情報を呼び出して、お 手本の曲をダウンロードしたり、ウェブページで気に入ったミュージックファイ ンダーのレコードをダウンロードし、楽器に追加することができます。ミュー ジックファインダープラスについて詳しくは、インターネット上の下記ページを ご覧ください。 http://www.yamaha.co.
スタイルを制作する ( スタイルクリエーター ) スタイル制作の方法 スタイル制作には、下記の3つの方法があります。制作したスタイルは、編集もできま す(81ページ)。 ■ リアルタイム録音 ..................................................................................................75ページ 楽器を演奏してスタイルを録音します。内蔵スタイルの中から自分が作りたいスタイル にもっとも近いイメージのものを選んで一部を差し替えたり、新しいスタイルを作った りすることができます。 ■ ステップ録音 ..........................................................................................................79ページ 譜面を書いていくように、音の高さや長さなどのデータを選んで録音します。データ入 力で録音できるので、楽器を演奏しなくてもスタイルを作れます。 ■ スタイル組み立て ................
スタイルを制作する ( スタイルクリエーター ) されます。リズムチャンネル以外のチャンネルでは、いったん元のデータを削除して から録音します。 内蔵スタイルを基にリアルタイム録音する場合 オーバーダブ録音可能 内蔵スタイルを基に「BASS」〜 「PHR2」チャンネルを録音すると きは 基のデータを削除してから録音しま す。 「BASS」〜「PHR2」チャン ネルにオーバーダブ録音(75ページ ) することはできません。 1 録音/編集の基となるスタイルを選びます(別冊クイックガイド25ページ)。 既存のスタイルを使わずに新しいスタイルを作るときは、手順5で表示される画 面で[C](NEW STYLE)ボタンを押してください。 2 3 ス タ イ ル の 設 定 / 制 作 を す る オーバーダブ録音不可能。 録音前にデータを削除します。 設定画面を表示させます: [ファンクション]→[F] DIGITAL REC MENU [B]ボタンを押して、スタイル制作の画面(スタイルクリエーター画面)を表示さ せます。 スタ イルク リエ ーター 画面下 部の RECORD画面( チャ ンネル
スタイルを制作する ( スタイルクリエーター ) 8 [F](REC CH)ボタンを押しながら[1▼]〜[8▼]ボタンを押して、録音チャンネ ルを指定します。 録音チャンネルを解除するときは、もう一度[1▼]〜[8▼]ボタンを押します。 8 10 9 8 9 [1▲]〜[8▲]ボタンを押してボイス選択画面を表示させ、録音するチャンネル のボイスを選びます。 元の画面に戻るには、[戻る]ボタンを押します。 10 削除したいチャンネルがある場合は、[J](DELETE)ボタンを押しながら該当す るチャンネルの[1▲]〜[8▲]ボタンを押します。 [J]ボタンを離す前にもう一度同じ[1▲]〜[8▲]ボタンを押すと、削除を取り消 すことができます。 11 録音できるボイスの制限 ・ 「RHY1」チャンネル オルガンフルートボイスとスー パーアーティキュレーションボイ ス以外 ・ 「RHY2」チャンネル ドラムキット/SFXキットのみ 「BASS」〜「PHR2」チャンネル ・ オルガンフルートボイス/ドラム キット/SFXキット/スーパーアー ティキュレーション以外 ス タ イ ル の 設 定 /
スタイルを制作する ( スタイルクリエーター ) リズムチャンネル以外のチャンネルに録音する場合のルール ● BASS、PHRASE1、PHRASE2チャンネルには、下記イラストのスケール ノート(C, R)を使って録音してください。 [使用できる鍵盤…C, D, E, G, A, B] イントロ、エンディングセクション を録音する場合は、このルールにと らわれず、自由にコード進行を持た せて録音すると、内蔵スタイルのよ うな楽しいスタイルを制作できま す。 ● CHORD1、CHORD2、PADチャンネルには、下記イラストのコードノート (C)を使って録音してください。 [使用できる鍵盤…C, E, G, B] C R C ソースコードを変える ソースコード をCM7としてではな く、他のコードルート/タイプで録 音したい場合は、録音前に、 PARAMETER画面での設定(85 ページ)が必要です。 C R C C=コードノート C, R=使用推奨ノート 自動伴奏(スタイル再生機能)はここで録音したデータを基(ソース)として、コー ド鍵域でのコード押鍵に従ってノート(音符)変換された音が鳴りま
スタイルを制作する ( スタイルクリエーター ) エディット ステップ録音 (EDIT) ここでの説明は、「リアルタイム録音」(75ページ)の手順4で「EDIT(エディット)」タ ブを選んだ場合に該当します。 ス タ イ ル の 設 定 / 制 作 を す る 「EDIT」画面では以下に示すポイントを除けば、ソングの場合(107ページ)と同じ方法 でノートデータなどのステップ録音/編集ができます。 ・ ソングクリエーターではエンドマークの位置が自由に変更できますが、スタイルクリ エーターでは変更できません。これは、選んだセクションによって自動的にスタイル の長さが決まるからです。たとえば、4小節のセクションを基にしてスタイルを制作 する場合、エンドマークの位置は自動的に4小節目の最後に設定され、スタイルクリ エーターのEDIT画面(イベントリスト)で変更することはできません。 ・ ソングクリエーターでは「1-16」画面で録音チャンネルを変更できますが、スタイ ルクリエーターのEDIT画面(イベントリスト)では変更できません。「BASIC」画面な どで録音チャンネルをあらかじめ設定しておいてください。
スタイルを制作する ( スタイルクリエーター ) アセンブリー スタイル組み立て (ASSEMBLY ) スタイル組み立てでは、内蔵スタイルからさまざまなパターン(チャンネル)を集めて1 つのスタイルを作りあげます。 1 基になるスタイルを選んでから、スタイル組み立てをする画面を表示させます。 「リアルタイム録音」(75ページ)の手順1〜4と同じ操作です。手順4では、 「ASSEMBLY」タブを選びます。 2 制作するスタイルのセクション(イントロ/メイン/エンディングなど)を選びます。 パネルのセクションボタン([イントロ]/[メイン]/[エンディング]ボタンなど)を押 して、セクション画面を表示させます。必要に応じて[6▲▼]/[7▲ ▼]ボタンを 押し てセクシ ョンを変 更し、[8▲](OK)ボタンを押して確定します。 セクションを構成するチャンネルが表示されます 2-1 A ス タ イ ル の 設 定 / 制 作 を す る B C 3 3 D 6 セクション画面 4 3 5 2-2 [A]〜[D]、[F]〜[I]ボタンを押して、パターンを置き替えるチャンネル
スタイルを制作する ( スタイルクリエーター ) スタイルを再生させながらスタイル組み立てをする場合 スタイルを再生させながらスタイル組み立てをする場合、再生方法を選ぶことが できます。再生方法を選ぶには、スタイル組み立て画面で[6▲▼]/[7▲▼] (PLAY TYPE)ボタンを押します。 ・ SOLO スタイル組み立て画面で選択しているチャンネルと、RECORD画面でRECに 指定されているチャンネルが再生されます。 ・ ON スタイル組み立て画面で選択しているチャンネルと、RECORD画面でOFF以 外に指定されているチャンネルが、再生されます。 ・ OFF スタイル組み立て画面で選択しているチャンネルの再生を消音します。 制作したスタイルを編集する リアルタイム録音、ステップ録音、スタイル組み立てで制作したスタイルを編集します。 ス タ イ ル の 設 定 / 制 作 を す る スタイル編集の基本操作 1 2 3 4 編集したいスタイルを選びます(25ページ)。 設定画面を表示させます: [ファンクション]→[F] DIGITAL REC MENU [B]ボタンを押して、スタイル制作
スタイルを制作する ( スタイルクリエーター ) グルーブ リズムのノリを変える (GROOVE) ここでの 説明は 、スタイ ル編集の 基本操作 (81 ページ)の手順 4で「GROOVE(グルー ブ)」タブを 選んだ場 合に該当 します 。 1 [A]/[B]ボタンを押して、編集メニュー (83ページ)を選びます。 1 4 3 2 ス タ イ ル の 設 定 / 制 作 を す る 2 3 [1▲▼]〜[8▲▼]ボタンを押して、データを編集します。 編集内容は、83ページを参照してください。 [D](EXECUTE)ボタンを押して、各画面でのデータ編集を実行します。 実行後は、このボタンが「UNDO(取り消し)」を実行するボタンになります。変 更されたデータを元に戻したい場合は、もう一度このボタンを押します。元に戻 せるのは、1つ前の操作だけです。 4 [I](SAVE)ボタンを押して、保存の作業をする画面(スタイル選択画面)を表示さ せます。スタイル選択画面で保存します(27ページ)。 編集したスタイルを保存せずにスタ イルを切り替えたり電源を切ったり すると、編集したデータは
スタイルを制作する ( スタイルクリエーター ) ■ グルーブ(GROOVE) スタイル再生の発音タイミング(クロック)を微妙にずらして、音楽のノリやグルーブ感 を演出します。ここでの設定は、選択されているセクションの全チャンネルに対して有 効です。 ORIGINAL BEAT (オリジナルビート) グルーブ効果をかけるビートを指定します。たとえば、「8 Beat」を選 ぶと、8分音符のタイミングにあるノートオン(音符)に対してグルーブ効 果をかけることになります。また、「12 Beat」を選ぶと、3連8分音符 のタイミングにあるノートオン(音符)に対してグルーブ効果をかけること になります。 BEAT CONVERTER (ビートコンバーター ) ORIGINAL BEATの項目で指定されたビートのタイミングを、どのタイ ミングに変える(コンバートする)かを設定します。たとえば、 ORIGINAL BEATの設定が「8 Beat」でBEAT CONVERTERの設定 が「12」の場合、セクション内のすべての8分音符タイミングのノー ト(音符)データが、3連8分音符のタイミングに変わることになります。
スタイルを制作する ( スタイルクリエーター ) チャンネル チャンネル単位で編集する (CHANNEL ) ここでの説明は、スタイル編集の基本操作(81ページ)の手順4で「CHANNEL(チャン ネル)」タブを選んだ場合に該当します。 1 [A]/[B]ボタンを押して、編集メニュー (下記参照)を選びます。 1 4 5 2 ス タ イ ル の 設 定 / 制 作 を す る 2 3 4 3 [1▲▼]/[2▲▼](CHANNEL)ボタンを押して、編集するチャンネルを選びます。 選ばれたチャンネルは、画面左上に表示されます。 [4▲▼]〜[8▲▼]ボタンを押して、データを編集します。 編集内容は、下記を参照してください。 [D](EXECUTE)ボタンを押して、各画面でのデータ編集を実行します。 実行後は、このボタンが「UNDO(取り消し)」を実行するボタンになります。変 更されたデータを元に戻したい場合は、もう一度このボタンを押します。元に戻 せるのは、1つ前の操作だけです。 5 編集したスタイルを保存せずにスタ イルを切り替えたり電源を切ったり すると、編集したデータは失われま
スタイルを制作する ( スタイルクリエーター ) スタイルファイルフォーマットの項目を設定する パラメーター (PARAMETER) スタイルファイルフォーマット (SFF) とは ソースパターン SOURCE ROOT (ソースルート) SOURCE CHORD (ソースコード) コード鍵域での コード変更 スタイルファイルフォーマットの編 集はノート(音符)変換の編集です。 リズムチャンネルの編集は効果的で はありません。 スタイルファイルフォーマット(SFF: Style File Format)と は、ヤマハの自動伴奏(スタイル再生)機能のノウハウを集大成 した「統一フォーマット」です。左図は、チャンネルが、スタ イル再生により実際にノート(音符)を発音するまでのプロセス を示しています。下記の操作では、これらの項目を自由に設定 できます。 ●ソースパターン ノート(音符)変換 NTR (コードルート変更に対する処理) NTT (コードタイプ変更に対する処理) スタイル再生で鳴る音符(ノート)は、コード鍵域でのコード変 更によって、さまざまな可能性がありますが、そのコード変更 によって変換
スタイルを制作する ( スタイルクリエーター ) 3 編集したスタイルを保存せずにスタ イルを切り替えたり電源を切ったり すると、編集したデータは失われま す。ご注意ください。 ソースパターン以外のコードで試聴 する スタイルクリエーター画面では、制 作中スタイルはソースパターンでの 試聴が原則ですが、例外的にソース パターン以外のコードでも試聴がで きます。NTRを「ROOT FIXED」 、 NTTを「BYPASS」、NTT BASS を「OFF」に設定(リズムチャンネ ルのほとんどがこの設定)すると、 SOURCE ROOT/CHORDの表示 が PLAY ROOT/CHORD に切り 替わります。この切り替わった PLAY ROOT/CHORDで再生させ てみたいコードルート/タイプを指 定すれば、ソースパターン以外の コードの試聴ができます。 [3▲▼]〜[8▲▼]ボタンを押して、データを編集します。 編集内容は、下記を参照してください。 4 [I](SAVE)ボタンを押して、保存の作業をする画面(スタイル選択画面)を表示さ せます。スタイル選択画面で保存します(27ページ)。 ■ SO
スタイルを制作する ( スタイルクリエーター ) ■ NTT(ノートトランスポジションテーブル) ソースパターンをノート変換するためのテーブル(一覧表)を決めます。 BYPASS (バイパス) NTRがROOT FIXEDの場合は、ノート変換をいっさい行なわないテーブ ルです。NTRがROOT TRANSの場合は、ルートだけノート変換される テーブルです。 MELODY (メロディー ) メロディーラインのノート変換に最適なテーブルです。「PHRASE 1」 や「PHRASE 2」のような、メロディーを含むチャンネルに使用しま す。 CHORD (コード) コードのノート変換に最適なテーブルです。 「CHORD 1」と「CHORD 2」が、ピアノやギターなどのコード演奏を含むときに使用します。 MELODIC MINOR (メロディックマイナー ) メジャーコードのソースパターンがマイナーコードに変換されるとき、長 3度の音が半音低く変換されるだけのテーブルです。また、マイナーコー ドのソースパターンがメジャーコードに変換されるとき、短3度の音が半 音高く変換されるだけのテーブルです。メジャー
スタイルを制作する ( スタイルクリエーター ) ■ NTT BASS ON/OFF (NTTベースオン/オフ) これをON(オン)に設定したチャンネルは、楽器にオンベースコードが認識されたときに ベースルートで再生されます。 ■ HIGH KEY (ハイキー ) コードのルート変更に対する、再生音のノート変換のオクターブ折り返し点を設定しま す。この折り返し点を境に、再生音のオクターブが切り替わります。NTRの設定(86ペー ジ)で「ROOT TRANS」が選ばれているときだけ、この設定ができます。 【例】ハイキーがFのとき ルート変更 再生音 CM C M FM F M C3-E3-G3 C 3-F3-G 3 F3-A3-C4 F 2-A 2-C 3 ■ NOTE LIMIT (ノートリミット) スタイルチャンネルに録音されたノートデータに対して発音域(最高音と最低音)を設定 します。発音域の設定によって、現実的 でない音 (高いベース 音や低い ピッコロ の音な ど)を鳴らさないようにし、発音域内のノートにオクターブシフトします。 ス タ イ ル の 設 定 / 制 作 を す る
パネル設定を登録する(レジストレーションメモリー ) レジストレーションメモリーは、ボイスやスタイルなどに関するパネル設定をボタンに 登録し、演奏中でもワンタッチで呼び出せる機能です。ボタンに登録したパネル設定 レジストレーション=登録 は、まとめて1つのバンク(ファイル)として保存します。 パネル設定を登録/保存する パネル設定を登録する 1 ボイスやスタイルなどのパネル設定を、登録したい状態にします。 レジストレーションメモリーで登録できる内容は、別冊「データリスト(パラ メーター一覧)」を参照してください。 2 レジストレーションメモリー [メモリー ]ボタンを押して、登録する項目を選ぶ 画面を表示させます。 この画面で選んだ項目だけが、登録されます。 1 2 パ ネ ル 設 定 を 登 録 す る 5 4 3 3 [2▲▼]〜[7▲▼]ボタンを押して、登録する項目を選びます。 すべての項目を登録しておいて、あ とで呼び出したくない項目を指定す ることもできます(92ページ)。 登録を中止するときは、[I](CANCEL)ボタンを押します。 4 5 [8▲]ボタンを押し
登録したパネル設定を呼び出す 登録したパネル設定を保存する レジストレーションメモリーでは、ボタンに登録した8個のパネル設定をまとめて1つ のバンク(ファイル)として扱います。 バンク4 バンク3 バンク2 バンク1 1 1 2 3 4 5 6 7 8 レジストレーションメモリー [レジストレーションバンク]ボタン[-] [+]を同時 に押して、バンク選択画面を表示させます。 レジストレーションメモリーの互換性 レジストレーションメモリーのバン クは、CVP-409/407/405/ 403/401で互換性があります。た だし、それぞれの機器の仕様などに より、完全な互換性が実現できない 場合があります。 2 [6▼]ボタンを押して、バンクを保存します(27ページ)。 選択 1 パ ネ ル 設 定 を 登 録 す る USB記憶装置のソング/スタイルを 登録したときは 登録を呼び出すとき、登録したデー タが入っているUSB記憶装置をド ライブに入れてください。 2 登録したパネル設定を呼び出す 1 レジストレーションメモリー [レジストレーションバンク]ボタン[-] [+
登録したパネル設定を呼び出す 3 レジストレーションメモリー [1]〜[8]ボタンのうち、緑色に点灯しているボタ ンの中から1つを選んで押します。 特定の設定を固定する(パラメーターロック) 特定の設定(エフェクトやスプリットポイントなど)を固定すれば、パネル設定が 切り替わってもその設定を維持できます。固定した設定は、パネルのボタンで変 更できます。 1 設定画面を表示させます: [ファンクション]→[J] UTILITY→タブ切替[ E] CONFIG 1→ [B]3 PARAMETER LOCK 2 [1▲▼]〜[7▲▼]ボタンを押して固定する設定を選び、[8▲]ボタンを押し て、チェックマークを付けて固定します。 登録したパネル設定を個別に削除する/名前を付ける 登録したパネル設定(バンクの中の8個のデータ)は、個別に削除したり名前を付けたり できます。 1 レジストレーションメモリー [レジストレーションバンク]ボタン[-] [+]を同時 に押して、バンク選択画面を表示させます。 2 [A]〜[J]ボタンを押して、編集するバンクを選びます。 3 [8▼](編集)ボタンを押して、レジ
登録したパネル設定を呼び出す 登録した設定のうち呼び出したくない項目を指定する (フリーズ) レジストレーションメモリーには本体のパネルで設定できるさまざまな項目を登録でき レジストレーションフリーズ画面で の設定は、この画面を抜けることに より記憶されます。画面を抜けずに 電源を切ると、設定が失われてしま いますのでご注意ください。 ますが、演奏の場面によってはすべての設定を呼び出したくない場合もあるかもしれま せん。たとえば、同じスタイルを鳴らしたまま、ボイスやエフェクト関連の設定を切り 替えたい場合です。このような場合にフリーズ機能を使えば、レジストレーションメモ リーのボタンを押しても、スタイル関連の設定だけは呼び出さずに現状のまま固定(フ リーズ)できます。 1 設定画面を表示させます: [ファンクション]→[E]REGIST SEQUENCE/FREEZE/VOICE SET→ タブ切替[E][F]FREEZE 2 [2▲▼]〜[7▲▼]ボタンを押して、呼び出したくない項目を選びます。 3 [8▲]ボタンを押して、呼び出したくない項目にチェックマークを付けます。 4 5 パ ネ
登録したパネル設定を呼び出す レジストレーションメモリーを呼び出す順番を決める (レジストレーションシーケンス) ライブやコンサートなど人前で演奏する場合などでレジストレーションメモリーをすば やく切り替える方法として、8個のパネル設定を呼び出す順番(レジストレーションシー ケンス)をあらかじめ決めておき、それを演奏時にタブ切替[E][F]ボタンやペダルで 呼び出す方法があります。 1 2 レジストレーションシーケンスを設定したいバンクを選びます(90ページ)。 設定画面を表示させます: [ファンクション]→[E]REGIST SEQUENCE/FREEZE/VOICE SET→ タブ切替[ E][F]REGISTRATION SEQUENCE 3 パ ネ ル 設 定 を 登 録 す る ペダルでレジストレーションを移動させる場合は、ペダルの設定をします。 [C]ボタンを押して、レジストレーションシーケンスを進めるペダルを決めます。 [D]ボタンを押して、レジストレーションシーケンスを戻すペダルを決めます。 4 [E](SEQUENCE END)ボタンを押して、レジストレーションシーケンスを
登録したパネル設定を呼び出す 5 パネル設定を呼び出す順番を決めます。 画面下方に表示される番号は、レジストレーションメモリー [1]〜[8]ボタンの 番号に対応しています。 設定を呼び出す順に、番号を左から右に入力します。 レジストレーションメモリー [1]〜[8]ボタンのどれかを押してから、[6▲▼] (INSERT)ボタンを押して、レジストレーションメモリー番号を入力します。 ・番号を置き替える [5▲▼](REPLACE)ボタンを押して、カーソルを当てた番号を現在パネルで 選ばれているレジストレーションメモリー番号に置き替えます。 ・番号をひとつずつ消去する [7▲▼](DELETE)ボタンを押して、カーソルを当てた番号を消去します。 ・番号をすべて消去する [8▲▼](CLEAR)ボタンを押して、番号をすべて消去します。 6 [F]ボタンを押して、レジストレーションシーケンス機能をオンにします。 7 [ダイレクトアクセス]ボタンを押してから[戻る]ボタンを押してメイン画面を表 示させ、設定した順にレジストレーションメモリーが呼び出されるか確認しま す。 パ ネ ル 設 定 を 登 録
ソングを再生/録音する 別冊クイックガイドの目次 ソングに合わせて練習してみましょう ........................................................14ページ 練習の前にソングを聞いてみましょう ..................................................14ページ 譜面を表示させましょう .........................................................................17ページ ガイドランプを使って片手練習してみましょう ...................................19ページ 繰り返し再生を使って練習してみましょう ..........................................21ページ 演奏を録音してみましょう .....................................................................21ページ カラオケや弾き語りをしてみましょう .....
ソング再生に関する操作 ソング再生に関する操作 基本的なソング再生の方法はクイックガイドで説明しましたので、ここではソング再生 に関する詳しい操作について説明します。 ■ ソングをスタート / ストップする ソングデータによっては、スタイル も同時に再生されます。 ソングのスタート/ストップは、基本的には、ソングコントロール[スタート/一時停止] ボタンを押してスタート、[ストップ]ボタンを押してストップしますが、下記の方法で スタート/ストップすることもできます。 スタート方法 シンクロスタート 鍵盤を弾くと同時にソング再生をスタートできます。 ソング停止中に、ソングコントロール[ストップ]ボタンと[スタート/一時停止]ボタンを 同時に押します。シンクロス タートを解 除するときは 、もう一度ソ ングコント ロール [ストップ]ボタンと[スタート/一時停止]ボタンを同時に押します。 ・ タップ機能 [タップ]ボタンを叩いて、テンポを指定すると同時に自動的にソングをスタートでき ます。シンクロスタート待機状態でタイミングを取りながらボタンを叩くと(4/4拍 子の場合は4回)、そのテンポでソングがスター
ソング再生に関する操作 ■ ソングを頭出し / 一時停止 / 巻き戻し / 早送りする ソングを頭出しする ソング停止中/再生中に[ストップ]ボタンを押します。 ソングを一時停止する ソング再生中に[スタート/一時停止]ボタンを押します。一時停止した位置からソングを 再生するには、もう一度[スタート/一時停止]ボタンを押します。 ソングを巻き戻し/早送りする 1 [巻き戻し]/[早送り]ボタンを押して、ソングを巻き戻し/早送りします。 ソング再生位置を示す画面が数秒表示されます。 フレーズマークが入っているソングの場合は、[巻き戻し]/[早送り]ボタンを押し フレーズマークとは ソングデータに設定されている、ソ ング中のある箇所を指定するデータ です。 て、フレーズマーク番号を指定します。フレーズマークで巻き戻し/早送りした くない場合は、ソング再生位置を示す画面で[E]ボタンを押して、「BAR」を選び ます。 フレーズマークがないソングの場合 フレーズマークがあるソングの場合 2 [戻る]ボタンを押して、ソング再生位置を示す画面を閉じます。 ■ ソングを繰り返し再生 / 連続再生する 1 ソ
ソング再生に関する操作 ■ 次に再生するソングを予約する 特定の設定を固定する(パラメー ターロック) 特定の設定(エフェクトやスプリッ トポイントなど)を固定すれば、パ ネル設定が切り替わってもその設定 を維持できます(91ページ)。 ソング再生中に、次に再生させるソングを1曲だけ予約できます。ステージ演奏などでス ムーズに次の曲を再生させたいときに便利です。ソングを予約するには、ソング再生中 に ソング選択画面で次に再生させ るソングを選びます。 次に再生させるソングは、ソング名右上に「NEXT(ネクスト)」と表示されます。 ソングの予約を解除するには、[8▼](キャンセル)ボタンを押します。 ■ ソングとスタイルを同時に再生する ソングとスタイルを同時に再生すれば、ソングの9〜16チャンネルがスタイルのチャン ネルに置き替えられるので、スタイルを使ってソングの伴奏部分を弾くことができます。 たとえば、下記の手順で、ソングに合わせてコードを弾いてみましょう。 ソングとスタイルを同時に再生するには、内蔵の「歌って楽しむ」フォルダーに入ってい るソングをおすすめします。 1 ソングを選びます(別冊ク
ソングの音量バランスや音色などを 調節する ( ミキサー ) USB 記憶装置を [USB TO DEVICE] 端子に接続したときにソングを 自動で選択する USB記憶装置を[USB TO DEVICE]端子に接続しただけで、自動的に先頭のソ ングを選択させることができます(ソングがフォルダーに入っていない場合のみ)。 1 設定画面を表示させます: [ファンクション]→[J]UTILITY→タブ切替[E][F]MEDIA 2 [3▲]/[4▲](SONG AUTO OPEN)ボタンを押して、ONを選びます。 ソングの音量バランスや音色などを 調節する ( ミキサー ) ソングに含まれるボイスについて「ミキサー画面で設定できる項目」(47ページ)の設定 ができます。操作は、「音量バランスや音色などを調節する(ミキサー )」(46ページ)の 基本操作の手順3で「SONG CH 1〜8」か「SONG CH 9〜16」を表示させ、手順 に従います。 たとえば、以下のようなことができます。 各チャンネルの音量バランスを調節する 1 ソングを選びます(別冊クイックガイド14ページ)。 2 [ミキサー ]ボ
練習機能 ( ガイド ) を使う 一部のボイスを変える 1~4 「各チャンネルの音量バランスを調節する(99ページ)」と同じ操作です。 5 [C]/[H]ボタンを押して、「VOICE」を選びます。 6 [1▲▼]〜[8▲▼]ボタンを押して、ボイスを変えたいチャンネルのボイス選択 画面を表示させます。 7 8 [A]〜[J]ボタンを押して、ボイスを選びます。 置き替えたボイスをソングに記憶させたいときは、セットアップの操作をします (122ページ「セットアップ」参照)。 セットアップの手順1では、 「VOICE」にチェックマークが入っていることを確 認しましょう。 練習機能 ( ガイド ) を使う ガイドの設定(SONG SETTING画 面での設定)を記憶させる ガイド機能の設定を、ソングデータ の一部として記憶させることができ ます(122ページ)。ガイド機能の設 定を記憶させると、次に同じソング を選んだときにガイド機能が自動的 にオンになります。 ガイドでは、ガイドランプが鍵盤を弾くタイミングや、押さえる鍵盤位置を示してくれ ます。また、ソング再生に合わせてマイク(CVP-405
練習機能 ( ガイド ) を使う 鍵盤演奏用 Follow Lights(フォローライツ) 正しい鍵盤を弾く練習をします(別冊クイックガイド19ページ)。 ソング再生中に、鍵盤を弾くべきタイミングが来たらソング再生が一時停止します。 正しい鍵盤を弾けば、ソング再生は続行されます。 Any Key(エニーキー ) 鍵盤を弾くタイミングを練習します。 ソング再生中に、鍵盤を弾くべきタイミングが来たらソング再生が一時停止します。 いずれかの鍵盤を弾けば、ソング再生は続行されます。 カラオケ用 Karao-Key(カラオキー ) 歌うタイミングに合わせて、ソング再生のタイミングをコントロールできます。 弾き語りをするときに便利です。 ソング再生中に、歌うべきタイミングが来たらソング再生が一時停止します。 いずれかの鍵盤を弾けば、ソング再生は続行されます。 Vocal CueTIME(ボーカルキュータイム)(CVP-405/403) 正しいピッチで歌う練習をします。 ソング再生中に、歌うべきタイミングが来たらソング再生が一時停止します。 マイクに向かって正しいピッチの声を出せば、ソング再生は続行されます。 ガイド
演奏を録音する ソングをチャンネルごとにオン / オフする ソングは、16のチャンネルで構成されています。ソングを再生させながら、各 チャンネルをオン/オフしてみましょう。通常、[トラック1]ボタンにチャンネル 1、[トラック2]ボタンにチャンネル2、[その他トラック]ボタンにチャンネル3 〜16が割り当てられています。 1 [チャンネル オン/オフ]ボタンを押して、ソングチャンネルをオン/オフする 画面を表示させます。 下の画面が表示されないときは、もう一度[チャンネル オン/オフ]ボタンを押 します。 2 [1▲▼]〜[8▲▼]ボタンを押して、各チャンネルをオン/オフします。 1チャンネルだけ再生するときは、再生したいチャンネルのボタンを押し続 けて「SOLO(ソロ)」にします。ソロを解除するには、もう一度ソロチャン ネルのボタンを押します。 演奏を録音する ソ ン グ を 再 生 / 録 音 す る マイクで歌った声は録音できません。 ご自分の演奏を録音し、楽器本体やUSB記憶装置などに保存できます。簡単な操作で録 音できる「クイック録音」 、トラック別にアンサンブルの曲を録音できる「多
演奏を録音する クイック録音 クイック録音では、ご自分の演奏を手軽に録音できます。 1 [録音]ボタンと[ストップ]ボタンを同時に押します。 から 録音のための空のソングが用意されます。 2 演奏に必要なパネル設定をします。 たとえば、以下の設定をしてみましょう。 ・ 右手1パートのボイスを録音する場合 ボイス選択画面を表示させて、ボイスを選びましょう(別冊クイックガイド11 右手/左手パートのボイスは別々の トラックに録音されます。 ページ)。 ・ デュアルボイス(右手1パート+右手2パート)を録音する場合 鍵盤パートオン/オフ[デュアル(右手2)]ボタンをオンにしましょう(39ページ )。 右手1/右手2パートのボイスを選ぶときは、ボイス選択画面を表示させて選 多重録音では、右手2パートを単独 で録音することが可能です。 びましょう(別冊クイックガイド11ページ)。 ・ 左手パートのボイスを録音する場合 鍵盤パートオン/オフ[スプリット(左手)]ボタンをオンにしましょう(40ページ)。 左手パートのボイスを選ぶときは、ボイス選択画面を表示させて選びましょ う(別冊クイックガイド11ペー
演奏を録音する 4 演奏しましょう。(=録音スタート) 録音をスタートさせるには、下記の方法があります。 ・ 鍵盤演奏を始める 手順3で[トラック1]/[トラック2]ボタンを押した場合は右手鍵域(38ページ) メトロノームを使う メトロノームを鳴らしながら(別冊 クイックガイド10ページ)録音でき ます。ただし、メトロノームの音は 録音されません。 で、[その他トラック]ボタンを押した場合はコード鍵域(67ページ)で演奏し ます。演奏を始めると同時に録音がスタートします。 ・ ソングコントロール[スタート/一時停止]ボタンを押す この場合、鍵盤演奏などで音を鳴らさない限り、空のデータが録音されてい きます。3拍めや4拍めなど弱起で始まる曲を演奏する場合は、この方法を 使ってください。 ・ スタイルコントロール[スタート/ストップ]ボタンを押す この場合、スタイルのリズムパートだけが鳴り、録音がスタートします。 録音を一時停止→再スタートする 録音を一時停止するときは、録音中 にソングコントロール[スタート/一 時停止]ボタンを押します。録音を 再スタートするときは、下記の操作 をします。 ・ [トラ
演奏を録音する 2 [録音]ボタンを押したまま[1▲▼]〜[8▲▼]ボタン を押して、録音するチャンネルを「REC」にします。 通常、鍵盤パートは1〜8チャンネル、スタイルは9 〜16チャンネルに録音します。チャンネル選択を解 [録音]ボタンを押したまま[2 ▲]ボタンを押して、チャン ネル2を「REC」にします。 9〜16チャンネルを一度に録音 チャンネルに指定する [録音]ボタンを押したまま[その他ト ラック(スタイル)]ボタンを押しま す。 除するときは、もう一度[録音]ボタンを押します。 3 MIDIパートを選んだ場合 ・ 単一チャンネルをMIDIに設定 MIDI 1〜16チャンネルすべての メッセージが録音されます。コン トロールキーボードを接続して録 音した場合、コントロールキー ボード側で出力チャンネルを設定 する必要がなくなります。 + 2 3 [C]/[D]ボタンを押して、録音するチャンネルに割 り当てるパートを選びます。 手順2で選んだ録音チャンネルに、鍵盤パートやス ・ 複数チャンネルをMIDIに設定 外部機器をつないで録音した場 合、録音チャンネルと同じMIDI
演奏を録音する 7 8 録音したソングを保存せずにソング を切り替えたり電源を切ったりする と、録音したデータは失われます。 ご注意ください。 手順2〜6を繰り返して、別のチャンネルを録音します。 [ソング選択]ボタンを押して、保存の作業をする画面(ソング選択画面)を表示さ せます。ソング選択画面で保存します(27ページ)。 ソングのチャンネルについて ソングのチャンネルには、初期設定では下記のパートが割り当てられています。 チャンネル 1 2 3 4 5 6 7 8 初期設定のパート RIGHT1 チャンネル 鍵 盤 パ ー ト 9 10 11 12 13 14 15 16 初期設定のパート RHYTHM1 RHYTHM2 BASS CHORD1 CHORD2 PAD PHRASE1 PHRASE2 ス タ イ ル パ ー ト 鍵盤パートについて 鍵盤パートとは、パネルの鍵盤パート[右手1]/[右手2]/[左手]のことです。初期 設定では、1〜8チャンネルに右手1(RIGHT1)パートが割り当てられています。 鍵盤パートの演奏は、通常この1〜8チャンネルに録音します。 スタイルパートに
演奏を録音する ステップ録音 ステップ録音では、メロディーやコードなどを録音できます。 ステップ録音の基本操作 1 [録音]ボタンと[ストップ]ボタンを同時に押します。 から 録音のための空のソングが用意されます。 録音 ストップ スタート/一時停止 新規ソング作成 シンクロスタート 2 設定画面を表示させます: [ファンクション]→[F] DIGITAL REC MENU 3 [A]ボタンを押して、ソング録音/編集の画面(ソングクリエーター画面)を表示さ せます。 3 4 ソ ン グ を 再 生 / 録 音 す る タブ切替[ E][F]ボタンを押して、タブを選びます。 メロディーを録音する場合 「1-16」タブを選びます。 .. コードを録音する場合 .........「CHORD」タブを選びます。 4 5 6 5 (手順4で「1-16」タブを選んだ場合)[F]ボタンを押して、録音するチャンネ ルを選びます。 6 [G]ボタンを押して、ステップ録音画面を表示させます。 7 ステップ録音をします。 メロディーを録音する場合 ....
演奏を録音する 以下の楽譜の例を使って録音したソ ングを楽器本体で譜面表示させた場 合、楽譜の例どおりに表示されない ことがあります。 メロディーを録音する 3種類の楽譜の例を使って、メロディーをステップ録音する方法をご紹介します。 例1 ここでの説明は、 「ステップ録音の基本操作」(107ページ)の手順7に該当します。 3〜5 1 6 7 2 ※ 譜面中の番号は、下記の操作手順番号に対応しています。 録音するボイスを選ぶときは、ステップ録音画面を表示させてからボイスを選びます。 1 [G]ボタンを押して、「 」を選びます。 1 2 3 ソ ン グ を 再 生 / 録 音 す る 4 [G]/[H]/[I]ボタンで選ぶ項目につ いて 110ページを参照してください。 108 2 [H]ボタンを押して、「Ten.
演奏を録音する 5 6 楽譜例に従って、C3、D3、E3、F3、G3、A3を弾きます。 [6▲▼]ボタンを押して、4分休符を入力します。 休符を入力するときは、[4▲▼]〜[8▲▼]ボタンを押して音符の長さを選んでか ら、もう一度同じボタンを押して、その音符の長さの空白を入力します。 7 8 C4を弾きます。 ソ ン グ を 再 生 / 録 音 す る ソングコントロール[ストップ]ボタンを押して、カーソルをソングの先頭位置に 移動します。 8 9 9 ソングコントロール[スタート/一時停止]ボタンを押して、録音したソングを試 聴します。 10 [戻る]ボタンを押して、ステップ録音画面を抜けます。 必要に応じて、録音したソングを編集します(117ページ)。 11 [I](SAVE)ボタンを押して、保存の作業をする画面(ソング選択画面)を表示さ せます。ソング選択画面で保存します(27ページ)。 録音したソングを保存せずにソング を切り替えたり電源を切ったりする と、録音したデータは失われます。 ご注意ください。 CVP-405/403/401 取扱説明書 109
演奏を録音する カーソルをソングの先頭位置に移動 する ソングコントロール[ストップ]ボタ ンを押します(109ページ 手順8 参照)。 データを個別に削除する 入力を間違えたときなどは、データを個別に削除できます。 1 ステップ録音画面(107ページ)で[A]/[B]ボタンを押して、削除するデータ を選びます。 2 [J](DELETE)ボタンを押して、選ばれたデータを削除します。 ステップ録音画面の [G]/[H]/[I] ボタンで選ぶ項目について ベロシティーとは 鍵盤を押す速度のことです。ただ し、鍵盤を「速く叩く」ほど「強く 弾く」と考えられるので、鍵盤を押 す強弱も表します。範囲は1から 127です。数値が大きくなるほど 強い(大きい)音になります。 [G]ボタンで選ぶ項目.......... 次に入力する音符のベロシティーです。 項目 録音されるベロシティ KBD.VEL fff ff f mf mp p pp ppp 実際に鍵盤を弾いた強さ 127 111 95 79 63 47 31 15 [H]ボタンで選ぶ項目..........
演奏を録音する 例2 ここでの説明は、「ステップ録音の基本操作」(107ページ)の手順7に該当します。 2~5 6~8 10~13 14~16 9 1 ※ 譜面中の番号は、下記の操作手順番号に対応しています。 この例では、一度押した鍵盤から指を離さずに画面操作をすることがありますので、ご 注意ください。 録音するボイスを選ぶときは、ステップ録音画面を表示させてからボイスを選びます。 1 [G]ボタンを押して、「 [G]/[H]/[I]ボタンで選ぶ項目につ いて 110ページを参照してください。 」を選びます。 1 2 3 ソ ン グ を 再 生 / 録 音 す る 4 2 [H]ボタンを押して、「Ten.
演奏を録音する ソ ン グ を 再 生 / 録 音 す る 6 [7▲▼]ボタンを押して、8分音符を選びます。 7 [H]ボタンを押して、「Sta.」 (スタッカート)を選びます。 8 楽譜例に従って、E3、F3、A3を弾きます。 9 [G]ボタンを押して、「 」を選びます。 10 [H]ボタンを押して、 「Ten.
演奏を録音する 例3 ここでの説明は、「ステップ録音の基本操作」(107ページ)の手順7に該当します。 1~4 5 6 7 ※ 譜面中の番号は、下記の操作手順番号に対応しています。 この例では、一度押した鍵盤を手順の最後まで離さずに(押し続けながら)画面操作をす ることがありますので、ご注意ください。 録音するボイスを選ぶときは、ステップ録音画面を表示させてからボイスを選びます。 1 [G]/[H]/[I]ボタンで選ぶ項目につ いて 110ページを参照してください。 [H]ボタンを押して、「Nrm.
演奏を録音する 5 C3とE3を押さえながら、[7▲▼]ボタンを押します。 [7▲▼]ボタンを押したあとも、C3とE3から指を離さないでください。 6 C3、E3、G3を押さえながら、[7▲▼]ボタンを押します。 [7▲▼]ボタンを押したあとも、C3、E3、G3から指を離さないでください。 7 C3、E3、G3、C4を押さえながら[7▲▼]ボタンを押し、続けて[5▲▼]ボタ ンを押します。 [5▲▼]ボタンを押してから、鍵盤から指を離してください。 ソ ン グ を 再 生 / 録 音 す る 8 ソングコントロール[ストップ]ボタンを押して、カーソルをソングの先頭位置に 移動します。 9 ソングコントロール[スタート/一時停止]ボタンを押して、録音したソングを試 聴します。 10 録音したソングを保存せずにソング を切り替えたり電源を切ったりする と、録音したデータは失われます。 ご注意ください。 114 [戻る]ボタンを押して、ステップ録音画面を抜けます。 必要に応じて、録音したソングを編集します(117ページ)。 11 CVP-405/403/401 取扱説明書 [I](
演奏を録音する コードを録音する ここでは、コードやセクション(イントロ、メイン、エンディングなど)変更のタイミン グ情報を録音します。下記の例を使って、コードチェンジをステップ録音する方法をご 紹介します。 ここでの説明は、「ステップ録音の基本操作」(107ページ)の手順7に該当します。 1 4 7 メインA ブレイク メインB C F G F 2,3 G7 C 5,6 8,9 ※ 譜面中の番号は、下記の操作手順番号に対応しています。 1 パネルのボタン[フィルインオン/オフ]がオフになっていることを確認してから、 メイン[A]ボタンを押します。 3 A B C C D 1 F ソ ン グ を 再 生 / 録 音 す る G 2 2 [5▲▼]ボタンを押して、2分音符を選びます。 3 スタイル鍵域で、コードC、F、Gを弾きます。 4 [ブレイク]ボタンを押します。 6 F G7 4 5 CVP-405/403/401 取扱説明書 115
演奏を録音する 5 [6▲▼]ボタンを押して、4分音符を選びます。 6 スタイル鍵域で、コードF、G7を弾きます。 7 メイン[B]ボタンを押します。 A B C D 7 9 C 8 録音したソングを保存せずにソング を切り替えたり電源を切ったりする と、録音したデータは失われます。 ご注意ください。 ソ ン グ を 再 生 / 録 音 す る データを個別に削除する 入力を間違えたときなどは、データ を個別に削除できます(110ペー ジ)。 8 [4▲▼]ボタンを押して、全音符を選びます。 9 スタイル鍵域で、コードCを弾きます。 10 ソングコントロール[ストップ]ボタンを押して、カーソルをソングの先頭位置 に移動します。 11 ソングコントロール[スタート/一時停止]ボタンを押して、録音したソングを試 聴します。 12 [戻る]ボタンを押して、ステップ録音画面を抜けます。 必要に応じて、録音したソングを編集します(117ページ)。 フィルインを入力する フィルインを入力するときは、 [フィルインオン/オフ]ボタンをオ ンにし て から メ イ ン[ A
演奏を録音する 録音したソングを編集する クイック録音、多重録音、ステップ録音で録音したソングを編集します。 ソング編集の基本操作 1 編集したいソングを選びます。 2 設定画面を表示させます: [ファンクション]→[F] DIGITAL REC MENU 3 [A]ボタンを押して、ソング録音/編集の画面(ソングクリエーター画面)を表示さ せます。 3 4 タブ切替[ E][F]ボタンを押してタブを選び、ソングを編集します。 ・ 部分的に再録音する(パンチイン/アウト録音)(REC MODE)...........118ページ ソングを部分的に再録音できます。 ソ ン グ を 再 生 / 録 音 す る ・ チャンネル単位で編集する(CHANNEL).............................................119ページ ソングデータ中のチャンネルごとに、データを削除したり トランスポーズをかけたりできます。 ・ データ単位で編集する(CHORD、1-16)............................................
演奏を録音する 部分的に再録音する ( パンチイン / アウト録音 ) レコードモード (REC MODE) 一度録音したソングは、部分的に再録音できます(パンチイン/アウト録音)。録音スター ト後、パンチインに設定されたタイミングとパンチアウトに設定されたタイミングの間 の範囲でのみ、上書き録音されます。録音中でも、パンチイン〜アウト以外の小節では 元データが再生されるだけで書き換わらないことがポイントです。パンチイン/アウト するタイミングは小節番号で指定するのが通常の方法ですが、鍵盤を押すタイミングや ペダルを踏むタイミングに設定する方法もあります。 ここでの説明は、 「ソング編集の基本操作」(117ページ)の手順4で「REC MODE」タ ブを選んだ場合に該当します。 1 [1▲▼]〜[6▲▼]ボタンを押して、再録音スタート(パンチイン)/ストップ(パン チアウト)の方法を選びます(下記参照)。 2 [録音]ボタンを押しながら、再録音したいトラックのボタンを押します。 + 3 ソングコントロール[スタート/一時停止]ボタンを押して、ソングをスタートし ます。手順1で選んだパンチインの
演奏を録音する パンチイン/アウトの設定による再録音の例 上記の設定の組み合わせによって、さまざまな方法で再録音できます。下記にいくつか の実例を挙げておきますので参考にしてください。 元データ REC STARTの方法 REC ENDの方法 1 2 3 4 5 スタート(上書き開始) *1 NORMAL REPLACE ALL 1 2 1 NORMAL PUNCH OUT AT=006 3 4 1 FIRST KEY ON REPLACE ALL 1 スタート(元データ再生) FIRST KEY ON PUNCH OUT 1 FIRST KEY ON PUNCH OUT AT=006 PUNCH IN AT=003 REPLACE ALL PUNCH IN AT=003 PUNCH OUT PUNCH IN AT=003 PUNCH OUT AT=006 スタート(元データ再生) 1 スタート(元データ再生) 1 スタート(元データ再生) 1 スタート(元データ再生) 1 8 7 8 7 8 7 8 7 8 7 8 7 8 5 録
演奏を録音する ■ クオンタイズ(QUANTIZE) たとえば、上図のような4拍子のフレーズを録音したとします。演奏しているときは、 正確に弾いているつもりでも、タイミングが微妙に遅れたり早かったりする場合もあり ます。クオンタイズはそういった微妙な「ずれ」を補正してデータを書き直す機能です。 CHANNEL (チャンネル) 分解能とは 4分音符を何分割できるかという 分割数です。 ソングデータのどのチャンネルにクオンタイズをかけるかを選びます。 クオンタイズの分解能を設定します。指定したチャンネルで使われている、最も細か い音符を選んでください。最も細かい音符が8分音符の場合は、「♪」を選びます。 クオンタイズのサイズを8分音符 (♪)に設定して、クオンタイズを 実行した場合 SIZE(サイズ) 設定値 4分音符 8分音符 16分音符 32分音符 16分音符+ 3連8分音符* 3連4分音符 3連8分音符 3連16分音符 8分音符+ 3連8分音符* 16分音符+ 3連16分音符* * マークの付いた3つのクオンタイズ設定は、異なる2つの音符の長さを同時に利用 してクオンタイズ
演奏を録音する ■ 特定チャンネルデータの削除(DELETE) ソングデータのうち、特定のチャンネルデータを削除できます。[1▲▼]〜[8▲▼]を押 して削除したいチャンネルを選び、[D](EXECUTE)ボタンを押して実行します。 ■ 異なる2つのチャンネルデータを1つのチャンネルデータとしてミックス(MIX) ソングデータの異なる2つのチャンネルデータを、1つのチャンネルデータとしてミッ クスできます。また、あるチャンネルデータのチャンネル番号を、別のチャンネル番号 に書き換えることもできます。 SOURCE1(ソース1) ミックスする元となるチャンネルを1〜16の中から選びます。ここで指 定したチャンネルのデータは、すべてミックスの対象となります。 SOURCE2(ソース2) ミックスする元となるチャンネルを1〜16の中から選びます。ここで指 定したチャンネルのデータのうち、ノート(音符)データだけがミックスの 対象となります。また、ここでは1〜16以外に「COPY」というメ ニューを選択できます。「COPY」を選択した場合は、ソース1で選んだ チャンネルデータのチャンネル番号を、デスティネー
演奏を録音する ■ セットアップ(SET UP) ミキサー画面(46ページ)での現在の設定やパネルボタンによる現在の設定を、セット アップデータとしてソングの先頭に書き込むことができます。ソング再生をスタートす ると、録音されたセットアップデータに従ってパネル設定が自動的に変更されます。 セットアップの手順 1 セットアップ画面を表示させます: [ファンクション]→[F] DIGITAL REC MENU→[A]SONG CREATOR→ タブ切替[E][F] CHANNEL→[B]5 SET UP 2 ソ ン グ を 再 生 / 録 音 す る [1▲▼]〜[7▲▼]ボタンを押して、ソング再生スタートに合わせてパネルに呼 び出したい項目(下記参照)を選びます。 SONG(ソング) 現在のミキサーでの設定値と、テンポを録音します。 KEYBOARD VOICE (キーボードボイス) 現在の鍵盤パート(右手1、2、左手)のボイス設定、鍵盤パートのオン/オ フなどのパネル設定をキーボードボイスとして録音します。録音されるパ ネル設定は、ワンタッチセッティングで記憶される項目と同じです。この 設定
演奏を録音する コード データ単位で編集する (CHORD、1-16) ここでの説明は、「ソング編集の基本操作」(117ページ)の手順4で「CHORD」/「116」タブを選んだ場合に該当します。 1 「1-16」タブを選んだ場合は、[F]ボタンを押して、編集するデータのチャンネ ルを選びます。 2 編集するデータにカーソルを合わせます。 カーソルを上下に動かす .............................[A]/[B]ボタンを押します。 カーソルを先頭に移動する ..........................[C]ボタンを押します。 カーソルを小節/拍/クロックで動かす ......
演奏を録音する 画面に表示されるデータについて 1 2 3 クロックとは 音符の分解能を表す単位です。分解 能とは、4分音符を何分割できるか という分割数です。CVP-405/ 403/401では、4分音符=1920 クロックです。 例 001 : 1 : 1440 拍(BEAT) 小節番号(BAR) クロック (CLOCK) 1 ソングデータ上の位置を表します。画面左下の表示と同じです。 2 データの種類を表します(下記参照)。 3 データの内容を表します。 「1〜16」画面のデータ ソ ン グ を 再 生 / 録 音 す る Note(ノート) 音符を示すデータです。ノートナンバー (鍵盤の位置)、ベロシ ティー (鍵盤を弾く強さ)、ゲートタイム(鍵盤を弾いている長さ)か ら構成されます。 Ctrl (コントロールチェンジ) ミキサー画面(46ページ)で調節できるボリューム、パン、フィル ター、エフェクトデプス(効果の深さ)など、ボイスをコントロール するデータです。0 Prog (プログラムチェンジ) ボイスを選択するデータです。 P.
演奏を録音する データを種類別に表示させる ( フィルター ) ソング編集画面ではさまざまな種類のデータが表示されるため、すべてを表示させると 煩雑で見づらい画面になることがあります。フィルター機能では、編集上必要なデータ だけを表示できます。 1 各ソング編集画面で、[H](FILTER)ボタンを押します。 2 [2▲▼]〜[5▲▼]ボタンを押して、表示させる項目を選びます。 3 [6▲▼]/[7▲▼]ボタンを押して、選んだ項目にチェックマークを付けます。 [H](ALL ON)・・・・すべての項目にチェックマークを付けます [I](NOTE/CHORD)・・・・NOTE/CHORDだけにチェックマークを付けます [J](INVERT)・・・・すべての項目のチェックマーク設定を逆にします 4 [戻る]ボタンを押して、設定を確定します。 [C]〜[E]ボタンは、次のフィルター画面に該当します。 MAIN ........................ 全体を表示させます CTRL CHG.............. コントロールチェンジを個別にフィルター設定します STYLE......
演奏を録音する リリックス 歌詞を編集する (LYRICS) ここでの説明は、 「ソング編集の基本操作」(117ページ)の手順4で「LYRICS」タブを 選んだ場合に該当します。この画面では、ソングを構成するデータのうち、歌詞に関す るデータを入力/編集します。 この画面での操作方法は、 「データ単位で編集する」(123ページ)の場合と基本的には 同じです。 データの種類 Name(ネーム) ソング名を入力します。 Lyrics (リリックス=歌詞) 歌詞を入力します。 Control Codes (コントロールコード) CR: 歌詞表示を改行します。 LF: 現在表示されている歌詞を消し、次の歌詞を表示させます。 歌詞書き替えの手順 1 書き替えたい歌詞にカーソルを合わせて、[4▲▼ ]/[5▲▼](DATA ENTRY) ボタン を押します。 ここで表示さ れる歌詞入 力画面で歌詞 を書き替え ます。 歌詞入力画面の操作方法は、ファイル名の入力方法(30ページ)と同様です。 2 [I](SAVE)ボタンを押して、保存の作業をする画面(ソング選択画面)を表示させ ます。ソング選択画面で
マイクを使う(CVP-405/403) 別冊クイックガイドの目次 カラオケや弾き語りをしてみましょう ........................................................34ページ マイクを楽器本体に接続しましょう .......................................................... 34ページ 歌詞を表示させて歌いましょう .................................................................. 35ページ カラオケをするのに便利な設定 ....................................................................37ページ テンポを調節する .....................................................................................10ページ 移調(トランスポーズ)する ..........................
ボーカルハーモニータイプを編集する 3 [A]〜[J]ボタンを押して、編集元となるボーカルハーモニーを選びます。 3 3 4 4 [8▼](編集)ボタンを押して、ボーカルハーモニー編集画面を表示させます。 5 編集元となるボーカルハーモニーを選び直すときは、[1▲▼]/[2▲▼]ボタンを 押します。 元の画面に戻って選び直したいときは、[8▲▼](RETURN)ボタンを押します。 8 マ イ ク を 使 う 5 保存せずに、ボーカルハーモニータ イプを切り替えたり電源を切ったり すると、設定内容は失われてしまい ますので、ご注意ください。 128 6 7 6 [3▲▼]〜[5▲▼]ボタンを押して、編集したい項目(129ページ)を選びます。 7 [6▲▼]/[7▲▼]ボタンを押して、手順6で選んだデータの値を変えます。 8 [I](SAVE)ボタンを押して、保存します(27ページ)。 CVP-405/403/401 取扱説明書
ボーカルハーモニータイプを編集する ボーカルハーモニー編集画面で編集できる項目 VOCODER TYPE (ボコーダータイプ) ハーモニーモード(132ページ)がボコーダー (VOCODER)に設定されて いる場合の、マイク入力音に対するハーモニー音の付け方を決めます。 CHORDAL TYPE (コーダルタイプ) ハーモニーモード(132ページ)がコーダル(CHORDAL)に設定されてい る場合の、マイク入力音に対するハーモニー音の付け方を決めます。 HARMONY GENDER TYPE (ハーモニージェンダー タイプ) ハーモニー音の声質(男性/女性)を入力音声から変更するかどうかを決め ます。 Off(オフ) ハーモニー音の声質を変更しません。 Auto(オート) 自動的にハーモニー音の声質が変化します。 LEAD GENDER TYPE (リードジェンダータイプ) 入力音声の声質(男性/女性)に関する設定です。この設定によってハーモ ニー音の最大発音数が異なります。Off(オフ)に設定するとハーモニー音 の最大音数は3声に、Off以外に設定すると2声になります。 Off(オフ) 入力
マイクやボーカルハーモニーの音質を調整する HARMONY1/2/3 PAN (ハーモニー 1/2/3パン) マイク入力音に付加されるハーモニー音の左右の定位を設定します。 HARMONY1〜3は、ハーモニー付加音の低音から高音の順に割り当て られています。 Random(ランダム) ハーモニー音の定位がランダムに移動する特殊な効果です。ボコー ダーハーモニー、コーダルハーモニーのときに効果があります。 L63>R〜C〜L
マイクやボーカルハーモニーの音質を調整する 4 [A]〜[J]ボタンを押して、設定項目(下記参照)を選びます。 5 [1▲▼]〜[8▲▼]ボタンを押して、設定します。 6 [戻る]ボタンを押して、マイク設定画面を抜けます。 「オーバーオールセッティング」で の設定は、画面を抜けるとメモリー に記憶されます。画面を抜けずに電 源を切ると、設定が失われてしまい ますのでご注意ください。 オーバーオールセッティングで設定できる項目 ■ 3BAND EQ(3バンドイコライザー ) 音をいくつかの周波数帯域(バンド)に分けて、各帯域のレベル(ゲイン)を上げ/下げ (ブースト/カット)することで、サウンドを補正する装置をイコライザーといいます。こ の楽器では、マイク入力音声の音質補正のために3バンド(LOW、MID、HIGH)のデジ タルイコライザーを搭載しています。 ・ Hz(ヘルツ) 対応するバンドの中心周波数を調節します。 ・ dB(デシベル) 対応するバンドを最大12dBまでブースト(増やす)したり、カット(減らす)したりす ることができます。 ■ NOISE GATE(ノイズゲート) マイク入力音
マイクやボーカルハーモニーの音質を調整する ■ VOCAL HARMONY CONTROL(ボーカルハーモニーコントロール) ここでは、ボーカルハーモニーがどのようにコントロールされるかを決めます。 ・ VOCODER CONTROL(ボコーダーコントロール) ボーカルハーモニーモードでボコーダーを選んだ場合(下記参照)、ボーカルハーモ ニーエフェクトはノート(音符)データによってコントロールされます。下記の設定 で、どのノートデータでボーカルハーモニーをコントロールするかを決めます。 SONG CHANNEL (ソングチャンネル) MUTE/PLAY(ミュート/プレイ) ソングの再生中に、下記で選ばれたチャンネルの発音を消音(MUTE)、 再生(PLAY)します。 OFF(オフ)/1〜16(チャンネル1〜16) OFF(オフ)に設定した場合は、ソングのノートデータによるハーモ ニーのコントロールは行ないません。1〜16のいずれかに設定した場 合は、楽器本体や外部MIDIシーケンサーからソングを再生していると き、ここで選んだチャンネルに録音されているノートデータによって ボーカルハーモニーがコントロール
トーク機能オンのときのマイク設定を調節する ・ VOCAL RANGE(ボーカルレンジ) 入力音声に適した自然なボーカルハーモニーを作り出します。 NORMAL(ノーマル) 標準的な設定です。 LOW(ロー ) 低い声に適した設定です。この設定はうなるような声や叫ぶような声に おいても適しています。 HIGH(ハイ) 高い声に適した設定です。この設定はマイクに近づいて歌うのにも適し ています。 ■ MIC(マイク) どのようにマイク入力音声がコントロールされるかを決めるものです。 ・ MUTE(ミュート) ON(オン)にすると、マイク入力音声をCVPの出力音から除きます。 ・ VOLUME(ボリューム) マイク入力音声のCVPの出力音としてのボリュームを調節します。 トーク機能オンのときのマイク設定を調節する トーク機能をオンにしたときのマイクの音量やエフェクトなどを調節します。 1 2 設定画面を表示させます: [ファンクション]→[G] MIC SETTING/VOCAL HARMONY [I](MIC SETTING)ボタンを押して、マイク設定画面を表示させます。 2 3 マ
トーク機能オンのときのマイク設定を調節する 4 5 6 [A]/[B]ボタンを押して、調節したい項目(下記参照)を選びます。 [1▲▼]〜[7▲▼]ボタンを押して、値を調節します。 [戻る]ボタンを押して、マイク設定画面を抜けます。 トークセッティングで調節できる項目 「トークセッティング」での設定は、 この画面を抜けるとメモリーに記憶 されます。画面を抜けずに電源を切 ると、設定が失われてしまいますの でご注意ください。 VOLUME(ボリューム) マイク入力音声の、CVPの出力音としてのボリュームを決めます。 PAN(パン) マイク入力音声の、CVPの出力音としてのパン(ステレオ定位)を決め ます。 REVERB DEPTH (リバーブデプス) マイク入力音声にかけるリバーブデプス(かかり具合)を設定します。 CHORUS DEPTH (コーラスデプス) マイク入力音声にかけるコーラスデプス(かかり具合)を設定します。 TOTAL VOLUME ATTENUATOR (トータルアッテネーター ) マイク入力音声を除いた、本体全体(鍵盤演奏音、スタイル、 ソングなど) DSP
クラビノーバを直接インターネットに接続する 楽器を直接インターネットに接続して、クラビノーバ専用サイトでいろいろなコンテン ツを楽しむことができます。この章では、コンピューターや通信規格に関する用語が出 てきます。わからない用語が出てきたら、「インターネット用語集」(149ページ)を参照 楽器を直接インターネットに接続し たときに表示できるのは、クラビ ノーバ専用サイトだけです。 してください。 楽器をインターネットに接続する ブロードバンドルーターまたはルーター機能付きモデムを通して、楽器を常時接続回線 (ADSL、光ファイバー、ケーブルテレビインターネット)に接続します。具体的な接続方 法(使用できるLANアダプターやブロードバンドルーターの種類など)については、イン ターネット上の下記URLでご確認ください。 http://www.yamaha.co.
クラビノーバ専用サイトを表示させる クラビノーバ専用サイトを表示させる クラビノーバ専用サイトでは、いろいろなコンテンツを楽しむことができます。クラビ ノーバ専用サイトを表示させるには、楽器がインターネットに接続された状態で、[イン ターネット]ボタンを押します。 クラビノーバ専用サイトが表示されます。 戻る ク ラ ビ ノ ー バ を 直 接 イ ン タ ー ネ ッ ト に 接 続 す る 136 CVP-405/403/401 取扱説明書
クラビノーバ専用サイトの操作方法 クラビノーバ専用サイトの操作方法 この章に掲載されているクラビ ノーバ専用サイトの画面は、操作 説明のための ものです。したがっ て実際の画面と異なる場合があり ます。クラビノーバ専用サイトで 扱われるコンテンツについては、 下記のヤマハ電子ピアノ/キーボー ドサイトをご覧ください。 http://www.yamaha.co.
クラビノーバ専用サイトの操作方法 文字を入力する ウェブページでパスワードを入力したりデータを検索したりするときの、文字の入力方 法については、31ページを参照してください。 直前に表示されていたウェブページに移動する 直前に表示されていたウェブページに戻るには、[1▲▼](戻る)ボタンを押します。 [1▲▼](戻る)ボタンを押す前に表示されていたウェブページに戻るには、[2▲▼](進む) ボタンを押します。 ホームページに移動する ホームページに戻るには、[3▲▼](ホーム)ボタンを押します。 ホームページを変更する 147ページを参照してください。 ク ラ ビ ノ ー バ を 直 接 イ ン タ ー ネ ッ ト に 接 続 す る 138 CVP-405/403/401 取扱説明書
クラビノーバ専用サイトの操作方法 ウェブページを更新/読み込みキャンセルする 表示されているウェブページを最新の情報に更新するには、[5▲](更新)ボタンを押し ます。ウェブページの表示に時間がかかるときなどにページの読み込みをキャンセルす るには、[6▲](中止)ボタンを押します。 インターネットの接続状態を見る インターネット画面の下には、接続状態を示すメッセージやアイコンが表示され ます。 メッセージ 1 3 2 4 強 中 弱 接続不可 ウェブページの読み込み状態に応じて、以下の3つのメッセージが表示されま す。 「ネットに接続されていません」 インターネットに接続されていないときに表示されます。このメッセージが表示 されているときは、ウェブページを見ることができません。1 のアイコンが表示 されます。 「Webページを開いています…」 ウェブページを読み込み中です。2 のアイコンが点滅します。 「Webページが表示されました」 ウェブページの読み込みが完了し、ページが完全に表示されます。2 のアイコン の点滅が止まります。 表示されているウェブページがSSLを使っているときは、3のア
クラビノーバ専用サイトの操作方法 ウェブページをブックマーク(お気に入り)に登録する ブラウザーに表示されているウェブページを、お気に入りとしてブックマークに登録で きます。ブックマークに登録したウェブページは、すぐに呼び出すことができます。 1 ブックマークに登録したいウェブページが表示されている状態で[4▲▼](ブック マーク)ボタンを押して、ブックマーク画面を表示させます。 ブックマーク画面では、現在登録されているブックマークが一覧表示されます。 一覧表示の下には、ブックマークに登録するウェブページのタイトルが表示され ます。 ク ラ ビ ノ ー バ を 直 接 イ ン タ ー ネ ッ ト に 接 続 す る 2 [3▲▼](追加)ボタンを押して、ブックマークを登録する画面を表示させます。 3 [1▲▼](▲/▼)ボタンを押して、登録するブックマークの位置を選びます。 3 4 4 [7▲▼](実行)ボタンを押して、ブックマークを登録します。 登録を中止するときは、[8▲▼](中止)ボタンを押します。 5 140 CVP-405/403/401 取扱説明書 [8▲▼](閉じ
クラビノーバ専用サイトの操作方法 ブックマークに登録したウェブページを表示させる 1 [4▲▼](ブックマーク)ボタンを押して、ブックマーク画面を表示させます。 2 [1▲▼](▲/▼)ボタンを押して、ブックマークを選びます。 2 3 3 [2▲▼](表示)ボタンを押して、登録したウェブページを表示させます。 ク ラ ビ ノ ー バ を 直 接 イ ン タ ー ネ ッ ト に 接 続 す る CVP-405/403/401 取扱説明書 141
クラビノーバ専用サイトの操作方法 ブックマークを編集する ブックマーク画面では、ブックマークのタイトルを変更したり、登録を削除した り、順番を入れ替えたりできます。 1 2 3 4 5 6 7 1 ▲/▼ ブックマークリスト内の選択位置を移動します。 2 表示 ブックマークリストで選ばれているウェブページを表示させます。 3 追加 ブックマークに登録するときに使用します(140ページ)。 4 項目移動 ブックマークの順番を入れ替えます。 1 位置を移動したいブックマークを選んだあと、 [4▲▼](項目移動)ボタンを押します。 画面下部の表示が変わり、選んだブックマークを移動できる状態になります。 2 [1▲▼](▲/▼)ボタンを押して、ブックマークを移動する場所の すぐ下のブックマークを選びます。 3 [7▲▼](実行)ボタンを押して、ブックマークを移動させます。 5 タイトル変更 選ばれているブックマークのタイトルを変更します。[5▲▼]ボタンを押す ク ラ ビ ノ ー バ を 直 接 イ ン タ ー ネ ッ ト に 接 続 す る と、文字入力画面が表示されます。文字入
クラビノーバ専用サイトの操作方法 環境設定画面について 環境設定画面では、インターネット接続に関する設定や、ブラウザーやコントロールメ ニューの表示方法などの、さまざまな設定を行ないます。環境設定画面には、ブラウ ザー、LAN、無線LAN、その他の4つの画面があります。 基本操作 1 [5▼](環境設定)ボタンを押して、環境設定画面を表示させます。 2 タブ切替[ E][F]ボタンを押して、設定画面を選びます。 3 [1▲▼](▲/▼)ボタンを押して、設定する項目を選びます。 3 4 4 [2▲▼]/[3▲▼](設定値変更)ボタンを押して、設定値変更画面を表示させます。 項目によっては、設定値変更画面が表示されずに設定内容が確定することもあり ます。 5 [2▲▼](▲/▼)ボタンを押して、設定値を選びます。 設定値は、[データダイアル]を使って選ぶこともできます。 ク ラ ビ ノ ー バ を 直 接 イ ン タ ー ネ ッ ト に 接 続 す る 文字を入力する 文字入力の画面が表示された場合、 文字の入力方法は、138ページを 参照してください。 5 6 CVP-405/4
クラビノーバ専用サイトの操作方法 6 [3▲](エンター )ボタンを押して、設定値を確定します。 設定値変更を中止するときは、[3▼](キャンセル)ボタンを押します。 7 [7▲▼](保存)ボタンを押して、環境設定画面での設定を確定します。 設定を中止するときは、[8▲▼](キャンセル)ボタンを押します。 ブラウザー 1 2 3 4 5 6 1 エンコード ブラウザーに表示される文字コードを設定します。 2 ホームページ ホームページとして登録されているウェブページのタイトルを表示/編集します。 3 現在のページをホームに登録 「ホームページを変更する」(147ページ)を参照してください。 4 ホームを初期状態に戻す ホームページの設定を工場出荷時の状態に戻します。 5 画像データの読み込み 「オン」にすると、ウェブページ内の画像データをブラウザーに表示します。 「オフ」にすると、画像データは表示されません。 6 タイムゾーン タイムゾーンを設定します。日本国内で使用している場合は、 「日本(GMT+ 9:00)」を選びます。 ク ラ ビ ノ ー バ を 直 接 イ ン タ ー ネ ッ
クラビノーバ専用サイトの操作方法 LAN LAN(ラン)の環境設定を行なうページです。有線、無線のどちらで接続する場合でも、 ここでの設定が必要です。 詳しくは、接続機器(ブロードバンドルーターなど)の設定を参照するか、インターネッ トプロバイダーにご確認ください。 設定をメモしておきましょう。 1 DHCPの使用 2 DNSサーバー 1 DNSサーバー 2 3 IPアドレス サブネットマスク ゲートウェイ 1 DHCPの使用 DHCPを使用するかどうか設定します。お使いのルーターがDHCPに対応し ている場合は、「使用する」を選びます。 2 DNSサーバー 1/DNSサーバー 2 プライマリー DNSサーバー /セカンダリー DNSサーバーのアドレスを設定しま す。DHCPの使用(1)で「使用する(DNSを手動設定)」か「使用しない」を選ん だ場合、ここでの設定が必要です。 3 IPアドレス/サブネットマスク/ゲートウェイ IPアドレス、サブネットマスク、ゲートウェイサーバーアドレスを設定します。 DHCPの使用(1)で「使用しない」を選んだ場合、ここでの設定が必要です。 無線 LAN
クラビノーバ専用サイトの操作方法 4 暗号化 暗号化するかどうかを設定します。 5 暗号キーの形式/暗号キーの長さ/暗号キー 暗号化(4)で「する」を選んだときに、ここで設定を行ないます。暗号キーの形 式や長さを設定します。 その他 1 2 3 4 5 1 プロキシサーバー /プロキシポート/プロキシを使わないサーバー プロキシサーバーの名前、ポート番号、プロキシを使わないサーバーを設定しま す。プロキシを使う場合のみ、ここでの設定が必要です。プロキシを使わない サーバーを複数設定するには、カンマ(,)で区切って入力します。 2 クッキーの削除 保存されているクッキーの情報をすべて削除できます。 3 ブックマークの全削除 登録されているブックマークをすべて削除できます。 4 環境設定の初期化 環境設定画面で行なったすべての設定項目を、工場出荷時の状態に戻します。 「インターネット設定の初期化」(148ページ)を参照してください。 5 接続情報 現在の接続情報の詳細を確認できます。 ク ラ ビ ノ ー バ を 直 接 イ ン タ ー ネ ッ ト に 接 続 す る 146 CVP-4
クラビノーバ専用サイトの操作方法 ホームページを変更する 初期状態では、クラビノーバ専用サイトのトップページがホームページとして登録され ていますが、自分で好きなページをホームページに指定することもできます。 1 ホームページに指定したいウェブページを表示させます。 2 [5▼](環境設定)ボタンを押して、環境設定画面を表示させます。 3 タブ切替[ E]ボタンを押して、 「ブラウザー」タブを選びます。 3 4 4 5 6 5 6 [1▼](▼)ボタンを押して、カーソルを「登録する」に合わせます。 [2▲▼]/[3▲▼](設定値変更)ボタンを押して、環境設定画面に入る前に表示さ せていたウェブページをホームページに指定します。 [7▲▼](保存)ボタンを押して、ブラウザーに戻ります。 ホームページの変更を中止するときは、[8▲▼](キャンセル)ボタンを押します。 ク ラ ビ ノ ー バ を 直 接 イ ン タ ー ネ ッ ト に 接 続 す る CVP-405/403/401 取扱説明書 147
クラビノーバ専用サイトの操作方法 インターネット設定を初期化する インターネット機能の設定は、クラビノーバの初期化( 33ページ)では初期化されません。 ここで説明する方法で初期化する必要があります。初期化すると、ブラウザーの設定だ けでなくインターネット接続に関する設定まで、環境設定画面で行なった設定が工場出 荷時の状態に戻ります(クッキーとブックマークの設定以外)。 1 [5▼](環境設定)ボタンを押して、環境設定画面を表示させます。 2 タブ切替[F]ボタンを押して、「その他」タブを選びます。 3 [1▲▼](▲/▼)ボタンを押して、「初期状態に戻す」を選びます。 3 4 4 [2▲▼]/[3▲▼](設定値変更)ボタンを押して、インターネット設定を初期化し ます。 クッキーには個人情報が含まれる場 合があります。 クッキー / ブックマークを削除する インターネット設定を初期化しても、クッキーとブックマークは削除されません。 クッキーとブックマークは、「その他」画面で削除してください(146ページ)。 ク ラ ビ ノ ー バ を 直 接 イ ン タ ー ネ ッ ト に 接 続
インターネット用語集 インターネット用語集 インターネット コンピューター間の通信規格にもとづいて、世界中のコンピューターや携帯電話などを接続した、 巨大な ネットワークのこと。 ウェブページ サイトを構成する各ページのこと。 クッキー (Cookie) ユーザーがウェブページとの間でやりとりした内容を記憶するしくみ。以前訪れたウェブページで、 そのと きに入力した内容があらかじめ表示されるのはこのしくみによるもの。 ゲートウェイ ネットワーク上で、通信規格の異なるデータを相互に変換してやりとりするためのシステム。 サイト 正式には「ウェブサイト」という。ひとまとまりに公開されているウェブページ群。 たとえば、"http://www.yamaha.co.
他の機器と接続して演奏する 外部機器と接続するときは、すべての機器の電源を切った 上で行なってください。また、電源を入れたり切ったりす る前に、必ず機器のボリュームを最小(O)にしてください。 感電または機器の損傷のおそれがあります。 CVP-405/403 MIC. LINE IN INPUT VOLUME MIN MIC. LINE 外部オーディオビジュアル機器と接 続する (345) n オーディオ接続ケーブルおよび変換プラグは、抵抗のないものをお使い ください。 CVP-401 楽器本体の音を外部オーディオ機器から出したり、 PHONES MAX アウト 外部機器で録音したりする (3[AUX OUT] 端子 ) 楽器本体をステレオなどに接続してより大きな音を出した 2 1 1 り、カセットテープレコーダーやデジタルオーディオ機器 などに接続して演奏を録音したりできます。マイクやギ ターなど[MIC.
外部オーディオビジュアル機器と接続する 楽器本体のスピーカーから外部機器の音を出す イン (4[AUX IN] 端子 ) 外部機器を楽器本体に接続して、外部機器の音を楽器本体 のスピーカーから出すことができます。シンセサイザーや 音源モジュールの音声出力端子([LINE OUT]端子など)を、 オーディオ接続ケーブルで、楽器本体底面端子パネルの [AUX IN]端子([L/L+R]と[R])(標準フォーン端子)に接続し ます。 信号方式と、表示方式(画面そのものの表示か歌詞/テキスト の表示か)を設定する(CVP-405) 1 2 設定画面を表示させます: [ファンクション]→[J](UTILITY)→タブ切替 [E][F]SCREEN OUT 信号方式は[1▲▼]/[2▲▼]ボタンで、表示方式(画 面そのものの表示か歌詞/テキストの表示か)は、[3▲ ▼]/ [4▲▼]ボタンで設定します。 外部機器の音を楽器本体から出力するときは、最初に外部 機器、次に楽器本体の順に、電源を切るときは、最初に楽 器本体、次に外部機器の順に、行なってください。 楽器本体 シンセサイザー、 音源モジュールなど
フットスイッチやフットコントローラーを使う ([AUX PEDAL ペダル ] 端子 ) フットスイッチやフットコントロー ペダル 3 ラーを使う ( 6[AUX PEDAL] 端子 ) 楽器本体底面端子パネルの[AUX PEDAL]端子に別売りの フットコントローラー (FC7)を接続すると、足を使って手 弾き音のボリュームを調節して演奏に抑揚を付ける(初期設 定)など、さまざまな機能をフットコントロールできます。 4 また、別売のフットスイッチ(FC4またはFC5)を接続する と、スタイルのスタート/ストップなど、さまざまなパネル のボタン機能を持たせることができます。 [1▲▼]ボタンを押して、選んだペダルに割り当てる機 能を選びます。 ペダルの機能については、次ページ「ペダルでコント ロールできる機能」を参照してください。 [2▲▼]〜[8▲▼]ボタンを押して、ペダルに割り当てる 機能に関する詳細設定(パートごとの有効無効など)を行 ないます。 表示される項目は、手順3で選んだ機能によって違いま す。表示される項目については、「機能ごとの設定」 (155ページ)を参照してください。 A
フットスイッチやフットコントローラーを使う 以下に、割り当てられる機能の一覧を掲載します。(*)印の機能については、フットコントローラーをご使用ください。フット スイッチでのご使用は不適です。 ペダルでコントロールできる機能 VOLUME(ボリューム) (*) 音量を調節します。AUX PEDAL端子に接続したペダルだけに設定することができます。 SUSTAIN(サステイン) ペダルを踏むと、演奏音に長い余韻が付きます。ペダルをゆるめると、すぐにサステインが かかった音は止まります。 SOSTENUTO(ソステヌート) ペダルを踏んだときに押さえていた鍵盤の音だけを、鍵盤から指を離しても長く響かせるこ とができます。ペダルを踏んでいるかぎり余韻が付きます。ただし、ペダルを踏んだあとに 弾いた音には効果はかかりません。たとえば、コードにサステインをかけて響かせながら、 他の音をスタッカートで演奏することができます。 SOFT(ソフト) ペダルを踏むと音量がわずかに下がり、音の響きが柔らかくなります。ピアノ音色など特定 の音色にだけ有効です。 GLIDE(グライド) ペダルを踏むと音程が変化
フットスイッチやフットコントローラーを使う ([AUX PEDAL ペダル ] 端子 ) SONG PLAY/PAUSE (ソングプレイ/ポーズ) ソングコントロール[スタート/一時停止]ボタンと同じです。 STYLE START/STOP (スタイルスタート/ストップ) スタイルコントロール[スタート/ストップ]ボタンと同じです。 TAP TEMPO(タップテンポ) [タップ]ボタンと同じです。 SYNCHRO START(シンクロスタート) [シンクロスタート]ボタンと同じです。 SYNCHRO STOP(シンクロストップ) [シンクロストップ]ボタンと同じです。 INTRO1〜3(イントロ1〜3) イントロ[I]〜[III]ボタンと同じです。 MAIN A〜D(メインA〜D) メイン[A]〜[D]ボタンと同じです。 FILL DOWN(フィルダウン) フィルを入れてから、左隣のMAINセクションに移ります。 FILL SELF(フィルセルフ) フィルを入れます。 FILL BREAK(フィルブレイク) ブレイクを入れます。 FILL UP(フィルアップ) フィ
外部 MIDI 機器と接続する ([MIDI ミディ ] 端子 )/ コンピューターや USB 機器と接続する 機能ごとの設定 ペダルに割り当てた機能ごとに設定できる項目が変わります。 SONG, STYLE, MIC (CVP-405/403), LEFT, RIGHT1, RIGHT2 (ソング、スタイル、マイク、レフト、ラ イト1、ライト2) ペダルの設定をするパートを選びます。 HALF PEDAL POINT (ハーフペダルポイント) (*) (CVP-405/403) ペダルをどのくらい踏み込めばダンパー効果やソフト効果(153ページ)が効き始めるのかを 設定できます。 DEPTH(デプス) ペダルでの効果のかかり具合(深さ)を調節します。 UP/DOWN(アップ/ダウン) PITCH BENDまたはGLIDEでピッチを上げる(UP)/下げる(DOWN)します。 RANGE(レンジ) PITCH BENDまたはGLIDEで、ペダルを踏んだときのピッチ変化の幅を半音単位で設定しま す。ミキサーのPITCH BEND RANGE(48ページ)と同じ効果です。 ON SPEED(オ
コンピューターや USB 機器と接続する 外部 MIDI 機器と接続する ミディ (7[MIDI] 端子 ) 外部MIDI機器との接続には、楽器本体底面端子パネルの MIDI端子を使用します。接続には、専用のMIDIケーブルを ご使用ください。 MIDI IN MIDIデータを受信する端子です。 MIDI OUT MIDIデータを送信する端子です。 MIDI THRU MIDI INから入ってきたデータをその まま送信する端子です。 MIDIの概念(MIDIって何? )、MIDIでできること、MIDI機 能の設定については、以下を参照してください。 • MIDIって何? .................................................................... 159ページ • MIDIでできること .............................................................
コンピューターや USB 機器と接続する ・[MIDI]端子を使った接続 USB 対応の記憶装置 ( デバイス ) の接続 本体の[MIDI]端子を使ってコンピューターと接続する場 合は、コンピューターの仕様により、2つの接続方法があ 以下に、接続と使い方の手順の概略を説明します。 USB記憶装置の取り扱いについては、最初に「USB記憶 ります。1つは、コンピューターにMIDIインターフェー スが内蔵されている場合で、楽器本体の[MIDI IN]端子と 装置の取り扱いについて」( 35ページ)をお読みください。 コンピューターの[MIDI OUT]端子を、同時に楽器本体の [MIDI OUT]端子とコンピューターの[MIDI IN]端子を、 楽器本体の[USB TO DEVICE]端子に、 USB対応の記 憶装置を、USBケーブルで接続します。 MIDIケーブルで接続します。 2 MIDIケーブル 楽器本体 MIDI IN端子 MIDI OUT端子 MIDI OUT端子 1 MIDI IN端子 MIDIインターフェース 内蔵コンピューター 2つめは、外付けのMIDIインタ
コンピューターや USB 機器と接続する /MIDIって何? コンピューターのハードディスクにバックアップ ■コンピューター上のデータをUSB記憶装置にコピーして 楽器本体で再生/再現する ■楽器本体で作ったデータをコンピューターのハードディス クにバックアップする コンピューターのハードディスクに保存してあるファイルを、 USB記憶装置にコピーしたあと、それらのファイルを楽器本体 楽器本体で制作したデータをUSB記憶装置に保存したあと、そ のUSB記憶装置をコンピューターに読み込ませてファイルを整 で再生/再現できます。楽器本体で作ったファイルだけでなく、 楽器本体以外で作られたスタンダードMIDIファイルやスタイル 理したり、コンピューターのハードディスクにコピーすること でバックアップをとったりできます。 ファイルフォーマットのスタイルファイルを、コンピューター のハードディスクからUSB記憶装置にコピーし、それらを楽器 本体の[USB TO DEVICE]端子に接続して、楽器本体で再生/再 現することもできます。 本体のデータをUSB記憶装置に保存します。 コンピューターのハードディ
MIDIって何? MIDIって何? アコースティック楽器の代表的なものにはアコースティッ クピアノやガットギターが挙げられます。ピアノは鍵盤を デジタル楽器(電子楽器)の演奏(MIDI)の録音と再生 録音 再生 たたくことにより、内部でハンマーが弦をたたいて鳴らし ています。ギターは直接弦を弾いて鳴らしています。 それではデジタル楽器と呼ばれるものは、どのようなしく みで音を鳴らしているのでしょうか? アコースティック楽器の発音 デジタル楽器(電子楽器)の発音 内蔵アンプ L 音源 (サンプリング音) 音源部 シーケンサー部 コントローラー (鍵盤など) USB記憶装置 内蔵アンプ R USB記憶装置 演奏情報 弦を弾くとボディが共鳴して 鳴る 鍵盤からの演奏情報をもとに、音源に 記録されているサンプリング音がス ピーカーを通して発音 n デジタル楽器の場合でも、AUX OUTから出力されるのは、オーディオ 信号です。 デジタル楽器で上のピアノに相当するのは「コントロー 上のイラストのように、電子楽器では演奏情報をもとに、 音源部(電子回路)に記憶されているサンプリング音(あら
MIDIって何? それでは、発音のもとになる演奏情報とはいったい何なの でしょうか? メッセージ名 本体の操作/パネル設定 たとえば、本体の鍵盤でグランドピアノの音色で「ド」の 音を4分音符の長さで強く弾いたとします。共鳴して音を ノートオン/オフ 鍵盤の演奏情報(ノートナンバーとベロシ ティーで構成) プログラム チェンジ ボイスの設定(コントロールチェンジのバ ンクセレクトMSB/LSBと合わせて設定) コントロール チェンジ ミキサーの設定(パン、ボリュームなど) 出すアコースティック楽器と異なり、電子楽器は「どの音 色で」 「どの鍵盤を」「どのくらいの強さで」 「いつ押さえた か」「いつ離したか」といった演奏情報を作り出します。そ して、ひとつひとつの演奏情報は、数値に置き替えて音源 部に伝えられます。音源部ではその数値をもとに、記憶さ れているサンプリング音が鳴るのです。 演奏情報の例 n ボイスナンバー (どのボイスで) 1(グランドピアノ) ソング、スタイルの演奏データもすべてMIDIデータです。 ノートナンバー (どの鍵盤を) 60(ド:C3) ノートオン(
MIDIって何? 本体の自動伴奏(スタイル)を使った演奏を外部 シーケンサーに録音する場合の例 MIDI でできること ■自動伴奏(スタイル)を使った演奏データ(1〜16チャンネ ル)をまとめて外部シーケンサー (コンピューター )などに録 イメージ図 音する。録音後、外部シーケンサーで編集した上で、本体 を鳴らす。 MIDIケーブル CVPのトラック(チャンネル) 外部シーケンサー 右手1 1チャンネル 1トラックに録音 右手2 2チャンネル 2トラックに録音 左手 3チャンネル 3トラックに録音 スタイルの各楽器 4チャンネル 4トラックに録音 スタイルの各楽器 5チャンネル 5トラックに録音 スタイルの各楽器 6チャンネル 6トラックに録音 スタイルの各楽器 7チャンネル 7トラックに録音 スタイルの各楽器 8チャンネル 8トラックに録音 スタイルの各楽器 9チャンネル 9トラックに録音 スタイルの各楽器 10チャンネル 10トラックに録音 スタイルの各楽器 11チャンネル 11トラックに録音 MIDI受信 楽器本体 MID
MIDI に関する設定 ● ESEQ( イーシーク ) ヤマハの多くの機器やミュージックデータで採用されてい る代表的なシーケンスフォーマットの1つです。 ・CVP-405/403/401は「ESEQ(イーシーク)」の再生 MIDI に関する設定 MIDI情報のやりとりについて、いろいろな設定ができま す。CVP-405/403/401では、使用場面に応じた標準的 に対応しています。 なMIDI設定がプリセットMIDIテンプレートとして10個用 意されています。またそれらを基に、ご自身で設定を編集 ● XF SMF(スタンダードMIDIファイル)をより拡張し、歌詞表示 したものを、独自のMIDI設定テンプレートファイルとし て、「ユーザー」画面に10個まで保存できます。また、 などを可能にしたヤマハ独自のシーケンスフォーマットで す。 ● STYLE FILE( スタイルファイル ) スタイルファイルフォーマットとは、ヤマハの自動伴奏(ス タイル再生)機能のノウハウを集大成した統一フォーマット です。 音色配列フォーマット MIDIでは音色を番号で指定します。(プログラムチェンジ ナンバーと言
MIDI に関する設定 4 タブ切替[E ][F]ボタンを押して画面を切り替え、 各種設定を行ないます。 「SYSTEM」 (システム)画面 MIDIシステムメッセージに関す る設定をします(165ページ)。 「TRANSMIT」 (トランスミット)画面 MIDI送信(トランスミット)に関す る設定をします(165ページ)。 「RECEIVE」 (レシーブ)画面 MIDI受信(レシーブ)に関する設定 をします(166ページ)。 「BASS」 (ベース)画面 MIDI受信ノートデータによる、 スタイル再生(自動伴奏)用ベース 音検出に関する設定をします (166ページ)。 「CHORD DETECT」 (コード ディテクト)画面 MIDI受信ノートデータによる、 スタイル再生(自動伴奏)用コード タイプ検出に関する設定をします (167ページ)。 5 6 各画面での設定が完了したら、[戻る]ボタンを押して、 MIDIテンプレート選択画面(プリセットまたはユーザー タブの画面)に戻ります。 タブ切替[E ][F]ボタンを押して「ユーザー」タブ を選び、設定した内容を保存します(27ペー
MIDI に関する設定 内蔵 MIDI テンプレートの説明 テンプレート名 機能 All Parts(オールパーツ) 鍵盤演奏パート(RIGHT1/2、LEFT)を含むすべてのパート(ソングパート以外)の演奏情報を、 外部に対してMIDI送信する設定です。 KBD & STYLE(キーボード&スタイル) 基本的にはAll Parts (オールパーツ)と同じですが、右手鍵域での演奏情報(ノートイベント) をRIGHT1/2パートではなくUPPER( アッパー )パートとして、また左手鍵域での演奏情報 (ノートイベント)をLEFTパートではなくLOWER(ロワー )パートとして、外部に対してMIDI 送信する設定です。 Master KBD(マスターキーボード) マスターキーボードとは、外部MIDI機器をコントロールすることを想定して設計されたMIDI キーボードのことです。ここでのMIDI設定は、CVPをマスターキーボードとして使えるよう になっています。 Song(ソング) すべての送信チャンネルがソングチャンネル1-16に設定されます。外部音源からソングデー タを流すときや外部シーケン
MIDI に関する設定 システム SYSTEM ● RECEIVE TRANSPOSE( レシーブトランスポーズ ) CVPが受信したノートイベントに対して、CVPのトランス MIDI システムメッセージに関する設定 ポーズ設定(別冊クイックガイド39ページ)を有効とするか どうかを決めます。 ここでの説明は、162ページの基本操作手順4でシステム (SYSTEM)画面を呼び出した場合に該当します。 ● START/STOP( スタート / ストップ ) 受信したFA/FCメッセージをソング再生、スタイル再生の どちらに使うかを決めます。 FA/FC=ソング、スタイルをスタート/ストップするMIDI メッセージです。FAがスタート、FCがストップのメッ セージです。 メッセージスイッチ ■メッセージスイッチ (MESSAGE SW ) ● SYS/EX.
MIDI に関する設定 ● Tx MONITOR(Txモニター ) MIDIメッセージが送信されたとき、該当するMIDIチャンネ ・KEYBOARD( キーボード ) 受信したノートメッセージが楽器本体の鍵盤をコントロー ル(1〜16)に対応したランプが短く点滅します。 ルします。 n ・EXTRA PART1 〜 5( エクストラパート 1 〜 5) MIDI受信専用に用意されている5つのパートです。通常、 本体で使用されていないパートです。通常のパート(マイク 違うパートに同じ送信チャンネルを設定した場合について 違うパートに同じ送信チャンネルを設定した場合、送信されるMIDIメッ セージは同じチャンネルにマージされます。その結果、接続している MIDI機器で予期せぬサウンドが鳴ったりするなど、不具合が生じる可能 性があります。 n 入力音声は除く)に、この5パートを追加することにより、 CVPは32チャンネルのマルチティンバー音源として機能 します。 SONG CH1-16の送信について SONG CH1-16の送信チャンネルを設定しても、プロテクトのかかっ ているソングはMIDI送
ボイスのプログラムチェンジナンバーの表示に関する設定 ボイス選択画面で、各ボイスに該当MIDIメッセージ(バンクセレ クトMSB-LSB-プログラムチェンジ)を表示させるかどうかを決 めます。外部MIDI機器からCVPのボイス指定する機会が多い場 合、ON(オン)に設定しておくと便利です。 [ファンクション]→ [J]UTILITY→タブ切替[E ][F] CONFIG 2画面で設定します。「DISPLAY VOICE NUMBER」 のON/OFFを切り替えてください。 手順 設定したいチャンネルを選び、そのチャンネルのオン/オフ を設定します。[I](ALL OFF)ボタンを選ぶと、すべての チャンネルがオフになります。 コードディテクト CHORD DETECT MIDI 受信によるスタイル再生用コードタイプの指定 ここでの説明は、163ページの基本操作手順4でコード n ディテクト(CHORD DETECT)画面を呼び出した場合に該 当します。 ・ ここで表示されるプログラムチェンジナンバーは、1番から数える 方式を取っています。したがって、実際のMIDIデータでは0番か ら数えるため、
付録 困ったときは 全般 クラビノーバの電源が入らない。 ・ 電源プラグを、本体と家庭用コンセント(AC100V)に確実に差し込 んでください(14ページ)。 電源スイッチをオンまたはオフにしたとき、「カチッ」と音がする。 ・ 電気が流れたためです。異常ではありません。 高音域や低音域で演奏すると、ピッチがオクターブ単位でジャ ンプしてしまうボイスがある。 ・ ピッチの限界に達するとピッチがシフトするボイスもあります。異常 ではありません。 電源を入れてからメイン画面が表示されるまでに時間がかかる。 ・ USB外部記憶装置が接続されていると、装置によっては、電源を入 れてからメイン画面が表示されるまでに時間がかかることがありま す。USB外部記憶装置を外してから電源を入れてください。 クラビノーバから雑音が出る。 ・ クラビノーバの近くで携帯電話を使ったり、呼び出し音が鳴ったりす ると、雑音が出る場合があります。クラビノーバの近くでは携帯電話 の電源を切ってください。 画面が明るすぎて(暗すぎて)画面の文字が見えない。 ・ [画面コントラスト]つまみで画面のコントラストを調節してくださ
ミキサーでスタイルやソングのリズムボイス(ドラムキットな ど)を変更したら、サウンドがおかしくなった。 ・ スタイルやソングのリズムボイス(ドラムキットなど)を変更する と、ドラムボイスに関する細かい設定がリセットされてしまい、もう 一度元のリズムボイスに戻しても元どおりのサウンドに戻らない場合 があります。ソングの場合は、ソングを先頭に戻す、スタイルの場合 はスタイルを選び直すと元の音に戻ります。 スタイル スタイルを再生できない。 ・ ソングコントロール[スタート/一時停止]ボタンを押しています。ス タイルコントロール[スタート/ストップ]ボタンを押してください。 ・ MIDIクロックが外部(INTERNAL以外)になっています。MIDIクロッ クを内部(INTERNAL)にしてください(165ページ)。 オルガンフルートボイスでダンパーペダルを踏むと、音が鳴り続ける。 スタイルがリズムしか再生されない(自動で伴奏が鳴らない)。 ・ オルガンフルートボイスでダンパーペダルを踏むと、音が鳴り続けま ・ スタイルがオンになっていません。[スタイルオン/オフ]ボタンを押 す。 して、スタイル
レジストレーションメモリー ソングの再生が途中で止まる。 ・ ガイド機能がオンになっています(正しい鍵盤が弾かれるのを待って レジストレーションメモリーに登録したソング/スタイルが、 呼び出されない。 ・ 登録したソング/スタイルがUSB記憶装置に入っていた場合、その USB記憶装置が本体に挿入されていません。登録したソング/スタイ ルが入ったUSB記憶装置を本体に挿入してください。 いる状態です)。[ガイド]ボタンを押して、ガイド機能をオフにしてく ださい。 電源を切る前に選んでいたソングが、電源を切ったら消えた。 ・ 電源を切る前に選んでいたソングがUSB記憶装置に入っていた場合、 同じUSB記憶装置を本体に挿入してください。 レジストレーションシーケンス設定画面で、レジストレーショ ンメモリーを呼び出す順番が表示されない。 ・ レジストレーションが入ったバンクが選ばれていません。レジスト レーションが入ったバンクを選んでください(90ページ)。 [巻き戻し]/[早送り]ボタンを押して表示させる「ソングポジ ション」画面で、小節番号が譜面と異なる。 ・(ソングのテンポに関係なく)一定の
譜面表示 テレビ画面に細い横線がちらつく。 ・ 通常のテレビ画面(インターレース方式)では細い横線がちらつくこと タイや、全音符などの長い音符を入力して本体で譜面表示した 場合、入力したとおりに表示されない。 ・ タイや、全音符などの長い音符を入力して本体で譜面表示した場合、 入力したとおりに表示されないことがあります。ソングのステップレ コード画面で[H]ボタンを押して「Ten.
データのバックアップ データのバックアップ 本体に保存したデータの万一の事故に備えて、大切な データはUSB記憶装置にバックアップとして保存する ことをおすすめします。 バックアップ対象のデータ 1 ソング*、スタイル、レジストレーションメモリーバン ク、ボイス 2 ミュージックファインダーのレコード、エフェクト**、 MIDIテンプレート、システムファイル * プロテクトがかかったソング(ソング名左上に「Prot. 1/Prot. 2」と表示されるソング)は、バックアップができません。た だし、ソング名左上に「Prot.
データのバックアップ 3 1と2のデータ(172ページ) 1 バックアップ先のUSB記憶装置を、楽器本体に挿入 /接続します。 2 設定画面を表示させます: [ファンクション]→[J] UTILITY→タブ切替 [E][F] OWNER 3 [D](BACKUP)ボタンを押して、バックアップ先の USB記憶装置に保存します。 バックアップしたデータのリストア(復帰)は、上記 手順3で[E](RESTORE)ボタンを押して行なってく ださい。 n ・ バックアップ/リストアは、完了するのに数分かかります。 ・ CVP-405/403/401以外で作成したバックアップデータはリスト アできません。 「ユーザー」画面に保存したプロテクトソングは、リストア の前に移動させてください。移動させないとリストアした ときに失われます。 付 録 CVP-405/403/401 取扱説明書 173
CVP-405の組み立て方 部品をまちがえたり、向きをまちがえないように注意して、 手順どおりに組み立ててください。 組み立ては、必ず2人以上で行なってください。 ネジは付属の指定サイズ以外のものは使用しないでくださ い。サイズの違うネジを使用すると、製品の破損や故障の 原因になることがあります。 指をはさんだりしないよう、十分ご注意ください。 譜面立ての上側は固定されていません。Aを立てかけるとき は、譜面立てに手を添えるなどして譜面立てが倒れないよう にしてください。 Aの背 面側を 下に して置 かな いでください。 ネジは各ユニット固定後、ゆるみがないようきつく締め直 してください。 解体するときは、組み立てと逆の手順で行なってください。 Aを 逆さに 置か ない でく ださ い。 プラス(+)のドライバーを用意してください。 3 BとCを固定します。 1 下記の部品を取り出します。 B C 1 BのA底面側をネジ2本で A 固定する。 組み立て中にキーカバーが開かないように、 キーカバーを上から押さえてシート をしっかり挟み込んでください。 A 2 Bのスピーカーボックス側を
CVP-405 の組み立て方 6 Eを固定します。 9 アジャスターを回します。 1 Dのプラスチックカバーを外 2 Eの底面に束ねてあるペダル す。 コードをほどく。 D アジャスターを回して、 床にぴったりつける。 E ■組み立て後、必ず以下の点をチェックしてください。 □ 部品が余っていませんか? D →組み立て手順を再確認してください。 □ 部屋のドアなどがこの楽器にあたりませんか? →楽器を移動してください。 □ この楽器がぐらぐらしませんか? E 3 ペダルコードをEとDの間 から出す。 4 Eが床にぴったり付いた状態で、E をネジ2本で固定する。 7 ぺダルコードを接続します。 →ネジを確実に締めてください。 □ ペダルを踏むと、ペダルボックス (E)がガタガタしませ んか? →アジャスターを回して床にぴったりつけてください。 □ ペダルコード、電源コードのプラグが、確実に本体(A) に差し込まれていますか? →確認してください。 1 ペダル コード のプラグ をペダル 端子に 差し込む。 プラグの矢印( )のある面が前面(鍵 盤側)になる向きで差し込
CVP-403の組み立て方 部品をまちがえたり、向きをまちがえないように注意して、 手順どおりに組み立ててください。 2 DとEにCを固定します。 1 Cの底面に束ねてあるペダルコード をほどく。 (外したビニールひもは、手順[6]で 使用します。 ) 組み立ては、必ず2人以上で行なってください。 ネジは付属の指定サイズ以外のものは使用しないでくださ い。サイズの違うネジを使用すると、製品の破損や故障の 原因になることがあります。 D ネジは各ユニット固定後、ゆるみがないようきつく締め直 してください。 E 解体するときは、組み立てと逆の手順で行なってください。 C プラス(+)のドライバーを用意してください。 2 長いネジ(6×25mm)で固定する。D、Eのどちらか を先に固定してから、もう片方を固定する。 1 箱を開けてCを取り出したあと、スチロールパッド2個を 取り出し、その上にAを置きます。 スチロールパッドは、A左下のヘッドフォンジャック部を保 護するように配置してください。 3 Bを固定します。 モデルによっては、Bの裏表で色が違う場合があります。こ の場合は、演奏者側から見た
CVP-403 の組み立て方 5 Aを固定します。 ■組み立て後、必ず以下の点をチェックしてください。 1 前面から見て、Aの張り出し部分が左右均等になるように調整す る。 □ 部品が余っていませんか? 2 前面から、短いネジ(6×16mm)で固定する。 □ 部屋のドアなどがこの楽器にあたりませんか? →組み立て手順を再確認してください。 →楽器を移動してください。 □ この楽器がぐらぐらしませんか? →ネジを確実に締めてください。 A □ ペダルを踏むと、ペダルボックス(C)がガタガタしませ んか? →アジャスターを回して床にぴったりつけてください。 □ ペダルコード、電源コードのプラグが、確実に本体(A) に差し込まれていますか? A →確認してください。 □ 使用中に楽器がきしむ、横ゆれする、ぐらぐらするなど の症状がでたら、組み立て図に従って各部のネジを締め 直してください。 6 ぺダルコードと電源コードを接続します。 組み立て後、楽器を移動するときは、必ず本体(A)の底面を持って ください。 天板やキーカバーを持たないでください。本体が破損したり、 お客様がけがをした
CVP-401の組み立て方 部品をまちがえたり、向きをまちがえないように注意して、 手順どおりに組み立ててください。 組み立ては、必ず2人以上で行なってください。 ネジは付属の指定サイズ以外のものは使用しないでくださ い。サイズの違うネジを使用すると、製品の破損や故障の 原因になることがあります。 2 DとEにCを仮留めします。 1 ペダルコードをほどきます。外したビニールひもは、手順7で使用します。 2 Cの両端にDとEを合わせて置きます。 3 長いネジ(6 × 20mm)で仮留めします。 ネジは各ユニット固定後、ゆるみがないようきつく締め直 してください。 E 解体するときは、組み立てと逆の手順で行なってください。 2 プラス(+)のドライバーを用意してください。 D C 3 1 L 1 箱を開けてCを取り出したあと、スチロールパッド2個を 取り出し、その上にAを置きます。 すべての部品を取り出し、部品がそろっているかを確かめ てください。 3 Bを固定します。 モデルによっては、Bの裏表で色が違う場合があります。こ の場合は、演奏者側から見たときにのBの色とD、Eが同じ になる向き
CVP-401 の組み立て方 8 アジャスターを回します。 5 Aをのせます。 アジャスターを回して、床にぴったりつけます。 指をはさんだり、Aを落としたりしないよう、十分 ご注意ください。 指定した位置以外を持たないでください。 必ずAの底面の端から10cm以上内側を持ってのせる。 A E R 10cm 以上 ■組み立て後、必ず以下の点をチェックしてください。 B D □ 部品が余っていませんか? →組み立て手順を再確認してください。 □ 部屋のドアなどがこの楽器にあたりませんか? →楽器を移動してください。 6 Aを固定します。 A □ この楽器がぐらぐらしませんか? →ネジを確実に締めてください。 1 前面から見て、Aの張り 出し部分が左右均等にな るように調整します。 □ ペダルを踏むと、ペダルボックス(C)がガタガタしませ んか? →アジャスターを回して床にぴったりつけてください。 □ ペダルコード、電源コードのプラグが、確実に本体(A) に差し込まれていますか? →確認してください。 □ 使用中に楽器がきしむ、横ゆれする、ぐらぐらするなど の症状がでたら、組み
フロッピーディスクドライブ(別売)の取り付け方(CVP-405) フロッピーディスクドライブのフロッピーディスクドライ ブケースとネジで楽器本体底面に取り付けることができま す。 本機に取り付けられる別売のフロッピーディスクドライブ については、仕様の「別売品」(182ページ)を参照してく ださい。 + (プラス) のドライバーを用意してください。 1 ケースの3か所の両面テープから、はくり紙をはがし、 フロッピーディスクドライブをケースに取り付けます。 3 フロッピーディスクドライブのネジ(4×10 mm)4本 で、本体底面の左側にフロッピーディスクドライブケー スを固定します。 ゴムのストッパーがある面を下にして 取り付ける 両面テープ 2 USBケーブルを、 ケースに収まるように折りたたみます。 付 録 180 CVP-405/403/401 取扱説明書 4 USBケーブルを[USB TO DEVICE]端子に接続します。
仕様 モデル名 CVP-405 音源 AWMダイナミックステレオサンプリング CVP-403 AWMステレオサンプリング 鍵盤 グレードハンマー3(GH3) 鍵盤 グレードハンマー(GH) 鍵盤 88 鍵盤数 320 ×240ドット QVGAカラー 5.7インチLCD ディスプレイ 320×240ドット QVGAモノクロ 5.
CVP-405 モデル名 CVP-403 USB オーディオレコーダー インターネットダイレクト接続 — LAN端子使用、無線LANイーサネットコンバーター(LAN端子使用 )、 USB-LANアダプター(USB TO DEVICE端子使用 ) USBフラッシュメモリー 接続可 フロッピーディスク(2HD, 2DD) 記憶媒体 デバイス ハードディスク USBタイプフロッピーディスクドライブ接続可 (USB TO DEVICE端子使用 ) USBタイプハードディスク接続可(USB TO DEVICE端子使用 ) フラッシュメモリー(内蔵 ) 約1.
索引 数字 GS .................................................................................................... 162 1-16 ................................................................................... 107、117 GUIDE LAMP(ガイドランプ)...................................................100 GUIDE LAMP TIMING(ガイドランプタイミング)................101 A ABリピート ....................................................別冊クイックガイド 21 H AI .............................................................................................
P U PANEL PART(パネルパート).....................................................47 [USB TO DEVICEデバイス]端子 ...............................................157 PARAMETER(パラメーター)......................................................85 USBオーディオレコーダー .........................別冊クイックガイド 41 PEDAL(ペダル)...........................................................................152 USB記憶装置の取り扱いについて .................................................. 35 PEDAL (ペダル)..............................................
カ 自動伴奏 ............................................................別冊クイックガイド24 ガイド ..............................................................................................100 初期化(インターネット設定)......................................................148 ガイドランプ(GUIDE LAMP)...................................................100 初期化(クラビノーバの設定).........................................................33 ガイドランプ(GUIDE LAMP)...................別冊クイックガイド 19 シングルフィンガー(SINGLE FINGER)...............................
チ フェードイン/アウト(ソング).......................................................96 チャンネル オン/オフ .......................................................................64 フェードイン/アウト(タイム).......................................................96 チャンネル(CHANNEL) .................................................. 84、117 フェードイン/アウト/ホールドタイム(FADE IN/OUT/HOLD TIME) ....64 チューン(TUNE)............................................................................48 フォーマット .....................................................
ボイスセット ......................................................................................61 レ ボイス編集 ..........................................................................................55 レシーブ(RECEIVE)...................................................................166 ボーカルキュータイム(Vocal CueTIME)............................... 101 レジストレーションシーケンス .......................................................93 ボーカルハーモニータイプ(VOCAL HARMONY TYPE)....127 レジストレーションシーケンス(REGISTRATION SEQUENCE)...
パネルボタン早見表 パネル上のボタンの位置は、各部の名称 (12 ページ ) で確認できます。 記号 [-][+](テンポ) ........................................................................................ ( [-][+](トランスポーズ)......................................................................... & 数字 [1]〜[4](ワンタッチセッティング(OTS))........................................ V [その他トラック(スタイル)] ................................................................I [ソング選択] ..........................................................................................
保証とアフターサービス ■ヤマハ電気音響製品サービス拠点 (修理受付および修理品お持込み窓口) サービスのご依頼、お問い合わせは、お買い上げ店、また はお近くのヤマハ電気音響製品サービス拠点にご連絡くだ さい。 ● 保証書 本機には保証書がついています。 保証書は販売店がお渡ししますので、必ず「販売店印・ お買い上げ日」などの記入をお確かめのうえ、大切に保 管してください。 ● 保証期間 お買い上げ日から本体は1年間、ヘッドフォンは6ヵ月です。 ● 保証期間中の修理 保証書記載内容に基づいて修理いたします。詳しくは保 証書をご覧ください。 ● 保証期間経過後の修理 修理すれば使用できる場合は、ご希望により有料にて修 理させていただきます。 下記の部品については、使用時間や使用環境などにより 劣化しやすいため、消耗に応じて部品の交換が必要とな ります。消耗部品の交換は、お買い上げ店またはヤマハ 電気音響製品サービス拠点へご相談ください。 ◆ 修理のご依頼/修理についてのご相談窓口 ヤマハ電気音響製品修理受付センター 受付時間 月曜日〜金曜日 9:00〜19:00、土曜日 9:00〜17:30(祝祭