Operation Manual

Page 121FT
DX
3000 OperaTing Manual
105 LSB RX CARRIER
Function: Adjusts the receiver carrier point for the LSB
mode.
Available Values: -200 Hz ~ 0 ~ +200 Hz (10 Hz steps)
Default Setting: 0
106 USB RX CARRIER
Function: Adjusts the receiver carrier point for the USB
mode.
Available Values: -200 Hz ~ 0 ~ +200 Hz (10 Hz steps)
Default Setting: 0
RX DSP Group
107 APF WIDTH
Function: Selects the Bandwidth of the Audio Peak
Filter.
Available Values: NARROW/MEDIUM/WIDE
Default Setting: MEDIUM
108 CONTOUR LEVEL
Function:AdjuststhegainoftheContourlter.
Available Values: -40 ~ 0 ~ 20 dB
Default Setting: -15
109 CONTOUR SHIFT
Function:AdjuststheQ-factoroftheContourlter.
Available Values: 1 ~ 11
Default Setting: 10
110 DNR LEVEL
Function: Set the Digital Noise Reduction response.
Available Values: 1 ~ 15
Default Setting: 3
111 IF NOTCH WIDTH
Function: Selects the bandwidth of the DSP NOTCH
lter.
Available Values: NARROW / WIDE
Default Setting: WIDE
112 HF CW SHAPE
Function: Selects the passband characteristics of the
DSPlterfortheCWmodeontheHFband.
Available Values: SOFT / SHARP
Default Setting: SOFT
SOFT: Primary importance is attached to the phase of
thelterfactor.
SHARP: Primary importance is attached to the
amplitudeofthelterfactor.
113 HF CW SLOPE
Function:SelectstheshapefactoroftheDSPlterfor
the CW mode on the HF band.
Available Values: STEEP / MEDIUM / GENTLE
Default Setting: MEDIUM
114 6M CW SHAPE
Function: Selects the passband characteristics of the
DSPlterfortheCWmodeonthe50MHzband.
Available Values: SOFT / SHARP
Default Setting: SOFT
SOFT: Primary importance is attached to the phase of
thelterfactor.
SHARP: Primary importance is attached to the
amplitudeofthelterfactor.
115 6M CW SLOPE
Function:SelectstheshapefactoroftheDSPlterfor
the CW mode on the 50 MHz band.
Available Values: STEEP / MEDIUM / GENTLE
Default Setting: MEDIUM
116 HF PSK SHAPE
Function: Selects the passband characteristics of the
DSPlterforthePSKmodeontheHFband.
Available Values: SOFT / SHARP
Default Setting: SHARP
SOFT: Primary importance is attached to the phase of
thelterfactor.
SHARP: Primary importance is attached to the
amplitudeofthelterfactor.
117 HF PSK SLOPE
Function:SelectstheshapefactoroftheDSPlterfor
the PSK mode on the HF band.
Available Values: STEEP / MEDIUM / GENTLE
Default Setting: MEDIUM
118 HF FSK SHAPE
Function: Selects the passband characteristics of the
DSPlterfortheFSKmodeontheHFband.
Available Values: SOFT / SHARP
Default Setting: SHARP
SOFT: Primary importance is attached to the phase of
thelterfactor.
SHARP: Primary importance is attached to the
amplitudeofthelterfactor.
119 HF FSK SLOPE
Function:SelectstheshapefactoroftheDSPlterfor
the PSK mode on the HF band.
Available Values: STEEP / MEDIUM / GENTLE
Default Setting: MEDIUM
120 HF SSB SHAPE
Function: Selects the passband characteristics of the
DSPlterfortheSSBmodeontheHFband.
Available Values: SOFT / SHARP
Default Setting: SHARP
SOFT: Primary importance is attached to the phase of
thelterfactor.
SHARP: Primary importance is attached to the
amplitudeofthelterfactor.
Menu Mode