Operation Manual

Page 117FT
DX
3000 OperaTing Manual
MODE-AM Group
048 AM LCUT FREQ
Function: Selects the cutoff frequency of the lower side
oftheRXaudiolterintheAMmode.
Available Values: OFF/100 ~ 1000 Hz (50 Hz/step)
Default Setting: OFF
049 AM LCUT SLOPE
Function:Selectsthelterslopeofthelowersideofthe
RXaudiolterintheAMmode.
Available Values: 6dB/oct / 18dB/oct
Default Setting: 6dB/oct
050 AM HCUT FREQ
Function: Selects the cutoff frequency of the upper side
oftheRXaudiolterintheAMmode.
Available Values: OFF/700 ~ 4000 Hz (50 Hz/step)
Default Setting: OFF
051 AM HCUT SLOPE
Function:Selectsthelterslopeoftheuppersideofthe
RXaudiolterintheAMmode.
Available Values: 6dB/oct / 18dB/oct
Default Setting: 6dB/oct
052 AM MIC GAIN
Function: Sets the microphone gain for the AM mode.
Available Values: MVCR/0 ~ 100
Default Setting: 30
When this menu is set to “MCVR”, you may adjust the
microphone gain using the front panel [MIC/SPEED]
knob.
053 AM MIC SEL
Function: Selects the microphone to be used in the AM
mode.
Available Values: FRONT / DATA / USB
Default Setting: FRONT
FRONT: Selects the microphone connected to the
front panel MIC jack while using the AM
mode.
DATA: Selects the microphone connected to pin 1 of
the PACKET Jack while using the AM mode.
USB: Selects the microphone connected to USB
Jack while using the AM mode.
MODE-CW Group
054 CW PITCH
Function: Adjusts your preferred CW tone pitch.
Available Values: 300 ~ 1050 Hz (50 Hz/step)
Default Setting: 700 Hz
055 CW LCUT FREQ
Function: Selects the cutoff frequency of the lower side
oftheRXaudiolterintheCWmode.
Available Values: OFF/100 ~ 1000 Hz (50 Hz/step)
Default Setting: 250
056 CW LCUT SLOPE
Function:Selectsthelterslopeofthelowersideofthe
RXaudiolterintheCWmode.
Available Values: 6dB/oct / 18dB/oct
Default Setting: 18dB/oct
057 CW HCUT FREQ
Function: Selects the cutoff frequency of the upper side
oftheRXaudiolterintheCWmode.
Available Values: OFF/700 ~ 4000 Hz (50 Hz/step)
Default Setting: 1200
058 CW HCUT SLOPE
Function:Selectsthelterslopeoftheuppersideofthe
RXaudiolterintheCWmode.
Available Values: 6dB/oct / 18dB/oct
Default Setting: 18dB/oct
059 CW AUTO MODE
Function: Enables/disables CW keying while operating
on SSB.
Available Values: OFF/50M/ON
Default Setting: OFF
OFF: Disables CW keying while operating on SSB.
50: Enables CW keying only while operating SSB on
50 MHz (but not HF).
On: Enables CW keying while operating on SSB (all
TX bands).
060 CW BFO
Function: Sets the CW carrier oscillator injection side
for the CW mode.
Available Values: USB/LSB/AUTO
Default Setting: USB
USB: Injects the CW carrier oscillator on the USB
side.
LSB: Injects the CW carrier oscillator on the LSB
side.
AUTO: Injects the CW carrier oscillator on the LSB
side while operating on the 7 MHz band and
below, and the USB side while operating on the
10 MHz band and up.
Menu Mode