HOME GYM
IMPORTANT SAFETY PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
Part List A A2 A1 A5 A9 A4 A15 A7 A3 A14 A11 A8 A12 A10 A16 A6 A17 -2- A13
Part List B B4 B1 C B2 C1 C9 C18 C19 B6 B7 B3 C2 C8 B5 C3 C10 C20 C4 C11 C5 C6 C7 C12 C13 C14 C15 C16 C17 8 M8 10 M10 12 M12 C21 C22 C23 C24 D D1 D2 D6 D8 D3 D7 D9 D4 D5 D10 E E1 E2 E3 E4 E5 E6 E7 E8 E9 F F1 F2 F3 F4 -3- F5 F6
PARTS DESCRIPTION MAIN BASE TUBE A1 A3 MIDDLE BASE TUBE MAIN SUPPORT TUBE A5 A7 TOP BRACE TUBE ROLL PAD TUBE A9 A11 SUPPORT TUBE FOR BUTTERFLY ARM A13 BUTTERFLY ARM(L) A15 T-BAR A17 HANDLE B2 BUTTERFLY CABLE B4 CHAIN B6 PULLEY C1 C3 C5 C7 C9 C11 C13 NUT(M8) C15 NUT(M10) C17 NUT(M12) C19 METAL BUSHING C21 WASHER C23 WAGON BOLT D1 PIN D3 CUSHION FOR STOP-SCREW D5 D7 HOOK PULLEY BRACKET D9 SQUARE END INSIDE CAP E1 E3 PULLEY HOUSING E5 RUBBER RING E7 ROUND END INSIDE CAP E9 SPONGE F2 WEIGHT STACK TOP PLATE F4 S
Part List C8 C19 C16 E1 C17 E9 E1 A11 C19 C16 E1 C20 E1 C15 C7 E3 C6 B6 F2 B7 C1 A12 E2 D5 A13 E9 C12 B6 D3 C18 C12 C21 C10 D4 C12 C8 C14 C15 F3 C4 C4 C9 C6 C14 B6 D2 D7 B6 C14 E7 C12 A9 C18 C14 C15 B6 C17 D6 C14 C16 C15 C14 C15 C2 F5 C15 E7 E4 C4 C14 C14 C18 B6 E1 B6 C6 C14 A2 C3 E1 D7 C12 E4 B1 B3 C3 C14 B4 C12 C8 C14 E9 C14 A3 C4 A2 D7 C15 C14 D8 A16 C14 C14 F5 E7 C4 C14 A10 E5 D7 E4 C6 C14 C15 C23 C18 C14 C4 C23 C11 C15 A8 B5 C4 C12
FIGURE 1 A4 E5 A5 C15 C14 A3 A2 C15 C14 C12 C4 C14 C8 C14 A1 C3 A2 PolyBag"P1" C3 HOW TO ASSEMBLY MAIN BASE TUBE & WEIGHT SLIDE TUBE ** use the polybag for "P1" mark ** C4 C14 Step 1.Assemble main support tube(A5) & side base tube(A2) at both side of main base tube(A1).fit them in the property hole with bolt(C3) & washer(C14) & nut(C15). Step 2.Put middle base tube(A3) by main base tube(A1).then fix if by bolf(C4).washer(C14) and nut(C15). Step 3.Attach rubber ring(E5).
FIGURE 2 F2 A6 C24 C22 A4 F1 D1 PolyBag"P2" HOW TO ASSEMBLE WEIGHT & MAIN SUPPORT TUBE D1 ** use the polybag for "P2" mark ** C22 Step 1.Slide weight plate(F1) over weight slider tube(A4). Equip weight pick up pole(A6) with tube housing(C24), then equip pin(C22) into the holes.Insert weight pick up pole(A6) into weight plate(F1),then slide weight stack top plate(F2) on top.
FIGURE 3 C8 C12 A7 C9 C14 D2 C14 C14 C15 A4 C13 C12 C4 C9 C14 C21 D5 D4 C12 C10 D2 C14 C15 A5 PolyBag"P3" HOW TO ASSEMBLE TOP BRACE TUBE MAIN SUPPORT TUBE & WEIGHT SLIDER C4 ** use the polybag for "P3" mark ** C9 Step 1.Equip top brace tube(A7) on weight slider tube(A4) & main support tube(A5),fix bolt(C4),washer(C14) & nut(C15),fix bolt(C8) & washer(C12). C10 Step 2.Equip pulley housing(D2) with main support tube(A5) and fix it by bolt(C9),washer(C14) & nut(C15). C12 C13 M C14 Step 3.
FIGURE 4 F3 C14 C5 A5 C23 A9 C15 C14 A8 C14 C5 F5 C14 C15 C15 C14 A16 C14 C4 C23 PolyBag"P4" C4 HOW TO ASSEMBLE BACKREST PAD ** use the polybag for "P4" mark ** C9 C23 C14 C15 Step 1.Equip seat tube(A8) with main support tube(A5),then fix if by bolt(C4),washer(C14) & nut(C15.) Step 2.Equip roller pad tube(A9) with seat tube(A8),then insert sponge(F5) from both sides. Step 3.Assemble backrest pad(F3) onto main support tube(A5) with bolt(C5) & washer(C14) Step 4.
FIGURE 5 F4 C17 C16 A10 C16 A9 D10 C12 C11 C2 A8 A5 C14 F5 C15 PolyBag"P5" C2 HOW TO ASSEMBLE LEG DEVELOPER WITH SEAT PAD ** use the polybag for "P5" mark ** C11 C12 C14 C15 C16 Step 1.Assemble leg developer(A10) at the middle of seat tube(A8) with bolt(C2),washer(C16) & nut(C17). Step 2.Assemble roll pad tube(A9) info leg developer (A10) then insert sponge(F5). Step 3.
FIGURE 6 C19 C16 C19 C17 A7 C17 C16 C20 C19 C17 C16 C20 A11 C20 A12 C16 C1 C20 A13 F6 C12 E8 C11 A17 E9 PolyBag"P6" C1 HOW TO ASSEMBLE LEG DEVELOPER & SUPPORT TUBE FOR BUTTERFLY ARM ** use the polybag for "P6" mark ** C11 C12 C16 C17 C19 Step 1.Insert bushing(C19) into support tube for butterfly arm(A11),fit top brace tube(A7) at middle sition. Insert bolt(C1) into top brace tube(A7) & (A11) and fix it by washer(C16) & nut(C17). Step 2.Insert metal bushing(C20) into butterfly arm(A11).
B1-2 B1-1 B1-4 B2-1 B2-2 B1-3 B3-5 B2-3 B1-5 B3-1 B3-2 B3-3 B3-4 -12- B3-6
FIGURE 7 B1-1 B1-3 A7 C15 B1 B1-5 B6 C15 C7 B7 C21 B1 E3 B1 C6 F1 D9 E3 B1-2 B1-4 C15 C14 C18 B1 B6 A7 A5 C18 C14 C15 C6 B1 B6 C4 PolyBag"P7" C4 HOW TO ASSEMBLE WIEGHT CABLE & PULLEY ** use the polybag for "P7" mark ** C6 C7 C14 (B7),then fix it by bolt(C7) & pulley housing(E3),through (A7)/(B7),fix it by(E3)/nut(C15). equip pulley(B6).
FIGURE 8 B2-1(L) B2-2(L)&(R) B2 C11 C6 B6 A12 B2 D2 C15 C15 C13 C6 B6 B2-3 B2-1(R) C11 A13 A5 B2 D2 B6 C6 B2 C13 C15 B2 D8 PolyBag"P8" HOW TO ASSEMBLE BUTTERFLY CABLE & PULLEY C6 ** use the polybag for "P8" mark ** C8 butterfly arm(A12) and fix it by bolt(C11) nut (C13). C13 Then equip pulley(B6),then fix it by nut(C15) & bolt(C6). C15 Insert it into pulley(B6) & pulley bracket(D8),then fix it by bolt(C6) and nut(C15).
FIGURE 9 B3-1 C15 B3-3 C14 A10 C18 C15 C18 B6 B3 C14 B3-2 C15 B3-5 D8 D9 C6 B6 B3 B6 C4 B3-4 C14 A5 C18 B3-6 B6 C15 B3 B3 D7 A1 C18 B6 B3 C15 B3 C6 B4 C6 D7 A1 C14 C4 PolyBag"P9" C4 HOW TO ASSEMBLE MAIN CABLE & PULLEY ** use the polybag for "P9" mark ** C6 into pulley(B6) & leg developer(A10).Put metal bushing (C18) at both side of leg developer(A10),then fix it by bolt(C4),washer(C14) & nut(C15). C14 C15 it into pulley(B6) & main support tube(A5).
FIGURE 10 B1 D7 A14 B3 D7 B5 A15 PolyBag"P10" HOW TO ASSEMBLE BACKREST PAD B5 D7 ** use the polybag for "P10" mark ** Step 1.Connect hook(D7) on both side between weight cable (B1) & lat pull bar(A14). Step 2.Connect chain(B5) with hook(D7) on both side between main cable(B3) & lat pull T-Bar(A15).
Warning: Make sure all bolt and nylon nut are tighten enough before using the machine.
