S Smart Translator Sy System Installation Instructions
Smart Translator System This system consist of circuit i it boards b d and a laptop mounted to the paver to monitor and record vibrator speeds while paving.
Smart Translator Sy S System How to mount the Translator Boxes
Smart Translator Sy S System Translator boxes can be mounted on the rail with a fabricated bracket… NOTE Vibrators plug into the bottom of the box
Smart Translator System The boxes can also be mounted on the kick guard d near the bottom of railing.
Smart Translator System Do NOT mount the boxes vertically. This can allow water through h h the h fittings on the top of the box and vibrator fittings on the side.
Smart Translator Sy S System The mounting h l are holes located in each corner of the box when the cover is removed
Smart Translator Sy S System Powering the Master Translator to Slave Boxes
Smart Translator Sy S System The Smart Translator System runs off 12/28 Volt system. Each box daisy chained off each other.
Smart Translator Sy S System The boxes are wired i d through strain reliefs and connected to each circuit board with the green connectors.
Smart Translator Sy S System The Master Translator is the only box that needs direct power from the machine. Usually connected to the Master Key Switch or connected to its own switch powered from the Master switch.
Smart Translator System Connect ring terminals to the power wire i and d attach to the key switch or an individual switch to power to Master Translator Box.
These 4 led lights will flash through a sequence t i twice, b before f the 1st light continues to flash when 12/28 volts are applied.
Smart Translator Sy S System Connect Master Translator to Slave 1 by connecting: Bare- SHIELD B Red- +DC IN Black- -DC IN WhiteWh te CAN N HI Green- CAN LO
Smart Translator System The Master Translator box needs d di direct power from the machine. Every other box Connects to each other th through h the th CAN IN and CAN OUT. CAN OUT Slave 2 CAN IN Vibs. 17-24 CAN OUT Slave 1 CAN IN Vibs. 9-16 M t Master CAN OUT SENSORS 12/28 volts TRACK WHEEL Vibs.
Smart Translator System There are desiccant packs placed on the inside covers with Velcro strips.
Smart Translator Sy S System How to H t assign i each h Box B in the correct sequence
Smart Translator Sy S System The Master Translator Box (Vibrators 1-8) has ALL the switches it h OFF
Smart Translator Sy S System Slave One (Vibrators 9-16) should have dip switch #1 ON
Smart Translator Sy S System Slave Two (Vibrators 17-24) should have dip switch #2 ON
Smart Translator System The Slaves between the Master Translator and the last Slave need d to h have JP 10 & JP 11 jumpers taken off both prongs and only put on one prong
Smart Translator System How to attach h the h Vibrators to the h Translator Boxes
Smart Translator System Bottom view of Master Translator Box The serial cable connects the h Master M Translator to the Computer Every box has 8 connectors labeled where each Vibrator will p plug g in.
Smart Translator System The Vibrator Speed p Sensor connects to these extension cables to attach h to the h Translator Boxes. There are 10ft. cables and 20ft.
Smart Translator System This is the serial cable that connects the Master Translator to the computer.
Smart Translator System The Smart Vibrators are monitored on th P the Panasonic i Tough Book CF-19.
Smart Translator System The Power Converter should be connected to the same 12/28 volt switch the Master Translator is connected to.
Smart Translator System Track Wheel and Relative Humidity Device Options
Smart Translator System Sid view Side i of f M Master t T Translator l t B Box Track Wheel Connector Sensor 1 and 2 is for Relative Humidity Device
Smart Translator Sy S System Attach the Track Wheel to ride on the track of the machine. Sometimes a slot might need to be cut. A b bracket k will ill need d to be made to hold the wheel in place. The Encoder should be mounted on the bottom of the bracket.
Smart Translator System The R l ti Relative Humidity Device connects to Sensor 1 and 2
Smart Translator System Labeling the control valves with the Vibrator Number is an easy way to identify what valve is for which h h vibrator
If there are any questions contact: Mike Rabideau- Field Service Technician Cell Phone- (262) 880-1211 E-mail- mikerabideau@racinefed.
