Workrite Sierra HXL™ Crank Assembly Instructions for 2-Leg Top Crank models #1500196 - Rev A
Workrite Sierra HXL™ 2-Leg Top Crank Workcenters - Assembly Instructions Parts grouped by carton A Leg Qty: 1 B Short Bracket Qty: 2 E F G H Crank Top Handle Qty: 1 J Shallow Hex Shaft Qty: 1 K Deep Hex Shaft Qty: 1 C Medium Bracket Qty: 2 D Top Leg Bracket Qty: 1 N Leg Qty: 1 P Long Bracket Qty: 1 O Top Leg Bracket Qty: 1 Q Crank Tube Qty: 1 S I L 4 mm Allen Wrench Qty: 1 M6 × 8 mm Button Head Machine Screw Qty: 12 #12 × ½" Self Tapping Phillips Head Screw Qty: 1 M6 × 16 mm Fl
Workrite Sierra HXL™ 2-Leg Top Crank Workcenters - Assembly Instructions 1 b ...continued Placement of the legs is very important. Take the time now to lay out the Legs (A & N), Leg Brackets (B, C, and P), Crank Tube (Q), and Top Leg Brackets (D & O) on the floor in the proper location. Note that the right leg will be on your left and vice versa when the assembly is seen from the back.
Workrite Sierra HXL™ 2-Leg Top Crank Workcenters - Assembly Instructions 3 Attach Short and Medium Brackets to Leg Assembly a Attach both Short Brackets (B) using M6 × 8 mm Button Head Screws (J). Do not tighten screws completely - allow them to slide left and right in Bracket. b Attach Medium Brackets (C) to sides of Legs using M6 × 8 mm Button Head Screws (H). If you have a 24" deep or less worksurface, use the holes to the rear of the Bracket as shown.
Workrite Sierra HXL™ 2-Leg Top Crank Workcenters - Assembly Instructions 5 Attach Legs to Hex Shafts and Crank Tube Turn Leg Assembly upside down. a Right Leg: Insert short end of Deep Hex Shaft (G) into leg. Slide Crank Tube (Q) over Deep Hex Shaft. Left Leg: Insert short end of Shallow Hex Shaft (F) into leg. Slide Crank Tube (Q) over Shallow Hex Shaft. F G Q Q Right Leg 6 a Left Leg Secure Long Bracket Attach Long Bracket to back of right Leg Cap using M6 × 8 mm Button Head Screws (J).
Workrite Sierra HXL™ 2-Leg Top Crank Workcenters - Assembly Instructions 8 Attach Base to Workrite Tabletops If you have a Base Only Model being attached to a non-Workrite table top, go to step 9 . Left Leg a Right Leg a Placement of the legs is very important. Lay out the leg assembly in the proper location. Note that the Right Leg will be on your left and vice versa when the assembly is upside down. b Align Base to the pre-drilled holes in top.
Workrite Sierra HXL™ 2-Leg Top Crank Workcenters - Assembly Instructions 9 a Base-Only Models & Other Tabletops: Position and Drill Hole for Top Crank Position the leg assembly on the face-down table top. Center the assembly on the table so that neither of the side legs overlap the edge. Measure carefully to ensure that your table will be positioned correctly as detailed below before drilling. Mark ¾" hole for crank handle: Trace around outside of leg bracket before removing leg assembly.
10 Base-Only Models & Other Tabletops (continued): Attach Base a Drill 1⁄8" × ¾" deep pilot holes through all of the bracket holes. TAKE EXTRA CARE TO NOT DRILL THROUGH TOP! b Install #12 × ¾" Phillips Head Wood Screws (M) into the Short Brackets (B) , Medium Brackets (C), and Long Bracket (P). DO NOT FULLY TIGHTEN SCREWS! c Tighten all of the M6 × 8 mm Button Head Screws (J) that were installed in steps 3 & 4 on the base to the brackets.
