W004532A 15 13 RELEASE 21 17 19 OPERATOR'S MANUAL 20V LI-ION CORDLESS DRILL Thank you for buying a WORKPRO product. Your cordless drill has been engineered and manufactured to WORKPRO’s high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
TABLE OF CONTENTS Introduction ------------------------------------------------------------------------------------------ 2 Caution ------------------------------------------------------------------------------------------------ 3 General safety rules -------------------------------------------------------------------------------- 3 Additional Safety Instructions --------------------------------------------------------------------- 4 Additional safety instructions for the charger ---------------------------
CAUTION Carefully read through this entire Instruction Manual before using your new Workpro Power Tool. Take special care to heed the Cautions and Warnings. Your Workpro power tool has many features that will make your job faster and easier. Safety, performance, and dependability have given top priority in the development of this tool, making it easy to maintain and operate. GENERAL SAFETY RULES b. Use personal protective equipment. Always wear eye protection.
GENERAL SAFETY RULES b. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. c. Use power tools only with specifically designated battery packs.
ADDITIONAL SAFETY INSTRUCTIONS The manufacturer shall not be liable for any changes made to the tool nor for any damage resulting from such changes. Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors. The following hazards may arise in connection with the tool’s construction and design: service the machine have to be acquainted with this Manual and must be informed about its potential hazards. Children and frail people must not use this tool.
ADDITIONAL SAFETY INSTRUCTIONS RELATED TO THE BATTERY PACK AND BATTERY SAFETY Do not dispose of the battery in a fire or put the battery into a microwave oven, conventional oven, dryer, or high-pressure container. Under these conditions, the battery may explode. Use only the WORKPRO batteries supplied with the WORKPRO Tool or WORKPRO-approved replacements. Do not use the battery to power any device other than the WORKPRO tool it was sold with.
UNPACKING Ensure that you have all the accessories and tools needed for assembly and operation. This also includes suitable personal protective equipment. Unpack all parts and lay them on a flat, stable surface. Remove all packing materials and shipping devices, if applicable. Make sure the delivery contents are complete and free of any damage. If you find that parts are missing or show damage do not use the product but contact your dealer.
YOUR PRODUCT 3 13 RELEASE 21 17 19 2 15 1 9 8 4 10 5 6 7 1/8 5/32 3/16 1/4 PH1 PH2 PH3 T10 T15 T20 11 1. 10mm keyless chuck 2. Torque adjustment ring 3. Two-speed gear control 4. Forward/reverse rotation control 5. Belt clip 12 13 6. Battery pack 7. Battery pack release button 8. On/off switch 9. Led light 10. Charger 8 11. 6pc drill bits 12. Extension bit holder 13.
SPECIFICATIONS Charger 120V ~ 60Hz Batteries 1.5Ah Charging Time 3-5H Drill No Load Speed 0-400/0-1500/min-1 Torque Settings 21+1 Torque 23 N.M. Drill Chuck Capacity 3/8"(10mm) keyless Max Drilling Capacity Steel / Wood 8mm / 22mm Weight 0.95Kg(2.09lbs) Battery 0.34Kg(0.
OPERATION 1. ON / OFF SWITCH (SEE B) C2 Depress the On/Off switch (8) to start and release it to stop your drill. The on/off switch is fitted with a brake function which stops your chuck immediately when you quickly release the switch.It is also a variable speed switch that delivers higher speed and torque with increased trigger pressure. Speed is controlled by the amount of switch trigger pression.
OPERATION 5. CHUCK ADJUSTMENT (SEE E) 7. AUTOMATIC SPINDLE LOCK (SEE G) To open the chuck jaws rotate the front section of the chuck. Insert the drill bit between the chuck jaws and rotate the front section in the opposite direction. Ensure the drill bit is in the center of the chuck jaws. Finally, firmly rotate the front chuck section in the opposite directions. Your drill bit is now clamped in the chuck.. The automatic spindle lock allows you to use it as a regular screwdriver.
OPERATION TOOL PROTECTION SYSTEM 10. Overheated: Under the condition above, if the tool does not start, the Battery are overheated. In this situation, let the Tool and Battery cool before pulling the Trigger Switch again. The tool will automatically stop during operation if the tool and/or battery are placed under one of the following conditions: Low battery voltage: The remaining Battery capacity is too low and the tool will not operate. In this situation, remove and recharge the Battery.