Owner's manual

ManualsBrandsWoodhaven ManualsTools4963: Taper Master

4963

Taper Master

Owners Manual

Please Read Carefully!

Part# Description Qty.

WS002 Washer 3

Part# Description Qty.

5760B Oval Nut 7

Part# Description Qty.

HB030 1" Bolt 1

Part# Description Qty.

BUSH001 1/8" Spacer 3

Part# Description Qty.

BUSH002 1/4" Spacer 2

Part# Description Qty.

5590 Knob 1

Part# Description Qty.

BUSH004 5/8" Spacer 1

Additional Hardware:

Parts listed below are not shown in the hardware

drawings. Refer to photos in the instructions:

Part Description Quantity

4963B MDF Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

4963A 32” Ultra Track Fence . . . . . . . . . . . . . . . . . . . . . 1

6305IC Inboard Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

4918B 17-3/4" Jig Bars . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Part# Description Qty.

NUT025 Square Nut 3

Part# Description Qty.

5505 Thumb Screw 1

Part# Description Qty.

5864 Ratchet Handle 3

BEFORE BEGINNING

The 4963 Taper Master makes cuts up to 40" long and

can be used in either miter slot of a table saw as long as the

miter slot is between 4" to 7-1/2" from the saw blade. Make

sure the 40" capacity is sufficient and your miter slot locations

are in the range given before proceeding. Identify and verify

that you have all the parts listed. Read the instructions at least

once, familiarizing yourself with the parts, before beginning

assembly. You’ll need a #2 Phillips screwdriver for assembly.

The Taper Master relies on the miter slot of your saw being

parallel to the saw blade for it to work properly. If this is not the

case, make those adjustments to your saw before proceeding.

The 4963 Taper Master may also be used on a band saw.

Summary of content (4 pages)

PAGE 1
4963 Taper Master Owners Manual Please Read Carefully! Additional Hardware: Parts listed below are not shown in the hardware drawings. Refer to photos in the instructions: Part# 5864 Part# NUT025 Part Description 4963B 4963A 6305IC 4918B MDF Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 32” Ultra Track Fence . . . . . . . . . . . . . . . . . . . . . 1 Inboard Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 17-3/4" Jig Bars . . . . . . . . . . . . . . . . . . . .
PAGE 2
1 ASSEMBLY Most people use their miter gauge in the left miter slot so these directions show that location being used. Open the 17-3/4" Jig Bars (4918B) and assemble/adjust the bars according to the instructions that come with them. Lay the Jig Bars (4918B) with their countersunk holes facing down, end-to-end in the miter slot of your saw. Align the mounting holes in the MDF Base (4963B) with the threaded holes in the bars so that the MDF Base overhangs the cutting path of the blade by 1/2" or less.
PAGE 3
INSTALL HANDLE 3 Insert a 1" bolt (HB030) in the desired T-slot in the Fence, then a 5/8" spacer (BUSH004) and a handle (5590) on the end of the bolt. Position the handle where desired on the Fence and tighten. INSTALL WORK STOP Insert two 1/4" spacers (BUSH002) on a thumb screw (5505) and start an oval nut (5760B - raised side first) on the end of the thumb screw. Slide it on to the T-slot on the edge of the fence, position it near the end of the fence for now and tighten. This will serve as a work Stop.
PAGE 4
OPTIONAL ACCESSORIES The 6305R Riser Kit increases the capacity to the toggle clamps to 2-3/4" thick stock. One kit required for each clamp. ©Copyright WOODHAVEN INC. 10/10/12 (800) 344-6657 or WWW.WOODHAVEN.