Manual

ManualsBrandsWoodhaven ManualsTools210: Linear Router Fence Adjuster

210 Parts List:

Parts listed below are not shown in the hardware

drawings. Refer to photos in the instructions.

Identify and verify that you have all of the

hardware and parts prior to assembly.

Part Description Quantity

200A Clamp Pad . . . . . . . . . . . . . . . . . . . . . . . . 2

210A Adjuster Plate . . . . . . . . . . . . . . . . . . . . . 1

210B Top Bracket . . . . . . . . . . . . . . . . . . . . . . . 1

210C 5-7/8" One Track w/hole . . . . . . . . . . . 2

210D 7-7/8" Ruler Bar . . . . . . . . . . . . . . . . . . . 1

4416 16" Ultra Track . . . . . . . . . . . . . . . . . . . . 1

210 Fence Adjuster

Please Read Carefully!

Part# Description Qty.

WB002 Brass Washer 7

Part# Description Qty.

BUSH050 3/8" Spacer 2

Part# Description Qty.

BUSH001 1/8" Spacer 4

Part# Description Qty.

5521 Thumb Nut 5

Part# Description Qty.

5860 Ratchet Handle 1

Part# Description Qty.

HB058 2-1/2" Bolt 2

Part# Description Qty.

BUSH1250 1/4" Spacer 4

Part# Description Qty.

BUSH002 1/4" Spacer 2

Part# Description Qty.

WFN002 1" Washer 2

Part# Description Qty.

5560 Knob 2

Part# Description Qty.

WS001 Washer 1

Part# Description Qty.

MF030 2" Screw 2

Part# Description Qty.

NUT006 Acorn Nut 2

Part# Description Qty.

NUT015 Hex Nut 4

Part# Description Qty.

HB020 3/4" Bolt 3

Part# Description Qty.

HB010 1/2" Bolt 1

Part# Description Qty.

MF032 3" Screw 2

Part# Description Qty.

WL001 Lock washer 2

Part# Description Qty.

MF006 5/8” Screw 4

Part# Description Qty.

5760B Oval Nut 6

Summary of content (4 pages)

PAGE 1
210 Fence Adjuster Please Read Carefully! 210 Parts List: Parts listed below are not shown in the hardware drawings. Refer to photos in the instructions. Identify and verify that you have all of the hardware and parts prior to assembly. Part Description 200A 210A 210B 210C 210D 4416 Clamp Pad . . . . . . . . . . . . . . . . . . . . . . . . 2 Adjuster Plate . . . . . . . . . . . . . . . . . . . . . 1 Top Bracket . . . . . . . . . . . . . . . . . . . . . . . 1 5-7/8" One Track w/hole . . . . . . . . . .
PAGE 2
BEFORE BEGINNING Read the instructions at least once, familiarizing yourself with the parts and assembly steps, before beginning. The Fence Adjuster is designed to attach to our 202, 203 or 204 Router Fences. You'll need a #3 Phillips screwdriver and a 7/16" wrench for assembly. FENCE ADJUSTER ASSEMBLY Insert two 5/8" screws (MF006) and 2" screws (MF030) through the holes shown in the Adjuster Plate (210A) and start an oval nut (5760B - flat side first) on the ends of each screw. See fig. 1.
PAGE 3
5B 210: Cross Section Diagram 5860 WB002 HB020 210B: Top Bracket BUSH001 WB002 NUT015 210C 5760B 4416 210A: Adjuster Plate Slide the Ultra Track under the Top Bracket so the head of the bolt engages in the top center T-slot of the Ultra Track and the ruler bar is in the groove of the Top Bracket.
PAGE 4
CLAMP ASSEMBLY Install a 3" screw (MF032) thru the countersunk hole of the Clamp Pads (200A). Install a lock washer (WL001) and nut (NUT015) on each screw and tighten. Screw a Knob (5521) all the way on to both of the 2-1/2" Bolts (HB058). Starting from the side of the Clamp Pad with the countersunk hole, thread the 21/2" bolt into the threaded hole in each Clamp Pad. If your table is 3/4" thick (Woodhaven's Phenolic Table), leave approximately 7/8" of the bolt projecting from the Clamp Pad.