Owner's manual

ManualsBrandsWoodhaven ManualsTools1472: Angle Ease, Universal

1470 & 1472 Angle-Ease

™

6002 & 6004 Angle-Ease

Owners Manual

U.S. Patent #6,742,558

Please Read Carefully!

Additional Parts List:

Parts listed below are not shown in the hardware

drawings. Refer to photos in the instructions:

Part Description Quantity

1470AS Side/Arm Assembly, pair . . . . . . . . . . . . . . . . 1

1470C 7-1/2” Double Track . . . . . . . . . . . . . . . . . . . . . 2

1475 Height Adjuster (in it’s own package) . . . . . 1

In addition, you will get ONE of the motor

blocks and plates below, depending on the

Angle-Ease model you purchased:

1470B 3.5” Motor Block . . . . . . . . . . . . . . . . . . . . . . . . 1

1472B 4.2” Motor Block. . . . . . . . . . . . . . . . . . . . . . . . 1

1470P Angle Ease Router Table Plate . . . . . . . . . . . 1

6000PA Horizontal Table Angle-Ease Plate . . . . . . . . 1

The Angle-Ease ﬁ ts

motors from these routers:

Router Model

FITS 3.5”

ANGLE-

EASE

FITS 4.2”

ANGLE-

EASE

Porter Cable 7518 No Yes

Milwaukee 5625 No W/ Shim

Porter Cable 892 Yes W/ Adapter R1

Porter Cable 690 Yes W/ Adapter R1

DeWalt 616/618 Yes W/ Adapter R1

Bosch 1617/1618 Yes W/ Adapter R1

Part# Description Qty.

MF015 1” Screw 6

Part# Description Qty.

5864 Knob - 1-5/8” 2

Part# Description Qty.

WN001 Nylon washer 4

Part# Description Qty.

WB002 Washer 4

Part# Description Qty.

5863 Knob - 1-1/8” 2

Part# Description Qty.

Ringpin1 Pin 2

Part# Description Qty.

5791B Barrel Nut 3

Part# Description Qty.

5760B Oval Nut 12

Part# Description Qty.

MF010 3/4" Screw 8

Part# Description Qty.

BUSH002 1/4" Spacer 4

Summary of content (4 pages)

PAGE 1
470 & 1472 Angle-Ease™ or 6002 & 6004 Angle-Ease Owners Manual U.S. Patent #6,742,558 Please Read Carefully! Additional Parts List: Parts listed below are not shown in the hardware drawings. Refer to photos in the instructions: Part Description Quantity 1470AS 1470C 1475 The Angle-Ease fits motors from these routers: Router Model Part# WB002 FITS 3.5” ANGLEEASE 1 2 1 1 1 1 1 Part# MF010 Description 3/4" Screw Qty. 8 Part# MF015 Description 1” Screw Qty.
PAGE 2
BEFORE BEGINNING Identify and verify that you have all the parts listed. Read the instructions at least once, familiarizing yourself with the parts, before beginning assembly. You’ll need two 7/16" wrenches, a #3 Phillips screwdriver and a flat blade screwdriver. ASSEMBLY Find the side/arm assembly (1470AS) that has the arm with the squared-off corner. Get the adjuster arm (1475A1) from the 1475 Height Adjuster package and attach it to the squared-off arm as shown, using two 3/4" screws (MF010).
PAGE 3
(BUSH002) on the knobs (5864). Using the side/arm assembly with the height adjuster arm attached to it, set the arm in the groove in the router block. Install the ratchet handle thru the slot in the arm, screwing it into the barrel nut. Slide the router block as far down on the arm as possible (away from the height adjuster arm) and tighten the knob. Flip the assembly over and connect the remaining side/arm assembly to the opposite side of the router block in the same manner. See fig.
PAGE 4
Place the arm plate (1475A2) with it’s groove covering the threaded rod and fasten it to the adjuster arm using the 3/4" screws (5771B). Align the top and bottom edge of both parts before tightening the screws. See fig. 9. Adjust the two nuts on the threaded rod, along with the washers, against the underside of the adjuster arm. Tighten the nuts against each other when you have adjusted the up/down slop out of the height adjuster. See fig. 9.