INSTALLATION MANUAL WOODBRIDGE SHOWER DOORS: MBSDC4876 MBSDC6076 R SHOWER DOOR TUB DOORS: MBTDC6062 IMPORTANT! WOODBRIDGE reserves the right to alter, modify or redesign products at any time without prior notice for the purpose of product improvement and customer experience. Please refer to WWW.WOODBRIDGEBATH.COM for the latest product details. Questions? Please Call Customer Support: 562-229-0088. (Monday - Friday 9 AM - 5 PM Pacific Time) Or Email: help.woodbridge@gmail.com 20200307 REV. 3 www.
IMPORTANT •WoodBridge reserves the right to alter, modify, or redesign products at any time without prior notice for product improvement or functionality. •Professional installation required. This product should be installed by someone experienced with the construction requirements for this type of project, the care necessary to responsibly and safely install, and familiarity with glass installation. •The safety of all installations is the responsibility of the installer who should be licensed and bonded.
•Improper use of the product. Do not place towels or anything else over guide rail. Aggressively opening or closing the slider may cause trauma to the glass which could lead to breakage. •Do not attempt to cut tempered glass. •Always wear safety equipment such as goggles, work gloves, proper footwear etc... during installation. •Instruct homeowner on how to conduct periodic inspections and how to properly maintain the glass and all hardware.
WOODBRIDGE R A B C B E A D ! F IMPORTANT INFORMATION REGARDING THE INSTALLATION OF THIS SHOWER DOOR A.Guide Rail Brackets must be firmly attached to the wall. Installation into a stud is strongly recommended. All of the guide rail bracket set screws must be accessible and tightened. B.Thread Lock must be applied to the set screws in both stoppers. Door-side stopper must be installed at the proper position to prevent the door from contacting the wall. C.
WOODBRIDGE R R E G Tools B D Tape Measure O O W Level Drill Bit Ø1/8" (3mm) D I R Drill Bit Ø3/16" (4mm) Safety Glasses Drill Bit Ø1/4" (6mm) Work Gloves Drill Bit Ø3/8" (10mm) Drill Bit Ø5/16" (8mm) Razor Knife Silicone Soft Head Hammer R D I R E G #3 Phillips Driver Bit Hacksaw B D O O W Painter's Tape Phillips Screwdriver Pencil Extender Driver Bit Soft Cloth or Blanket Power Drill O O W Miter saw Professional-grade Glass suction cup O O W Soft Wood Shim INSTRUCTIONS T
WOODBRIDGE R 17 16 15 1 2 3 4 5 14 6 7 8 13 9 12 10 11 18 5mm 4mm 3mm 2.5mm 2mm www.woodbridgebath.
WOODBRIDGE R Parts List 1 3 2 Bumper Strip x1 4 Guide Rail Bracket x2 5 Upper Guide Rail x1 7 6 Roller x2 8 Glass Door x1 Screw M4X30 Side Anti-Water Strip x2 13 x1 x1 16 x1 Anti-splash Threshold 12 Guide Block x1 14 Bottom Clamp x1 Handle 9 11 10 x2 Glass Door Stopper x5 Wall Anchor 15 Stationary Glass x1 17 x2 Screw M5X60 18 5mm 4mm 3mm 2.5mm 2mm Glass Bracket x2 Safety Pin x2 www.woodbridgebath.
O O W WOODBRIDGE Model Specific Preparation R W R E No Out-of-Plumb Adjustment; Verify threshold and walls with a level R E G D I R ±0.0 B D O O W Threshold must be level ±0.0 W 3” minimum threshold R E ! B D O O W E G D I R Threshold must be level ! R R PANEL PANEL DOOR DOOR R NOTE E G E W This model is reversible for right or left-hand door installation. The right-hand door installation is shown as an example throughout this manual.
WOODBRIDGE R Wall W W 90° W 1.Measure the distance between two finished walls. This distance is marked as W. Please see Fig 1 for details: Fig 1 www.woodbridgebath.
WOODBRIDGE a. R 16 2 4 2 Note: The Glass Brackets have been pre-installed to the roller bar. b. Door End Panel End W c. Door End(no holes) L d. 4 4 2. Your Upper Guide Rail (4) has been precut for your Shower model opening width: 48" or 60" for shower width. If W-width of your wall-to-wall opening is equal to the size of your shower model, it is unnecessary to cut the Upper Guide Rail and you can continue to Step 3.
WOODBRIDGE R a. b. 2 4 2 c. 3 d. Front Bracket core 16 e. Bracket core screw f. 2 3 16 g. 3. Use the allen key (18) to loose the screw on the Guide Rail Brackets (2) and Glass Door Stoppers (3). Slide the Glass Door Stopper and then the Guide Rail Bracket to the Guide Rail (4), use the allen key to tighten the parts to the guide rail temporarily. Please see Fig 3 for details. Fig3 3 5 1/8" 3 9/16" 2 3 16 4 www.woodbridgebath.
WOODBRIDGE R a. 13 b. 14 c. Fig4 4. Install Stationary Glass Loose the screw on Bottom Clamp (13). Disassemble the Bottom Clamp and install it on the Stationary Glass (14). Please see Fig 4 for details www.woodbridgebath.
WOODBRIDGE R a. b. 16 5. Loose the screws on the Glass Bracket (16), align the hole of the Glass Bracket to the holes on the Stationary Glass (14). Secure the Upper Guide Rail (4) to the Stationary Glass by fastening the screws on the Glass Bracket. c. Please see Fig 5 for details. Door end of guide rail 14 High spot of Adjustment Disk bushing Glass-to-Rail Bracket 16 Adjustment disk The outer Glass-to-Rail Bracket (#16) disk has an eccentric bushing for adjustment.
WOODBRIDGE a. 2 R b. 14 14 rotate disk(s) to level rail Door end of guide rail High spot of Adjustment Disk bushing The Stationary Glass (14) must be installed to the outside of the Top Guide Fig6 6. Place the Stationary Glass Assembly against the wall. Make sure the Stationary Glass and the Upper Guide Rail (4) are leveled. Please see Fig 6 for details. www.woodbridgebath.
R WOODBRIDGE R R E G R E G E G D I R B D O O W R E G D I R Door end O O W Fig 6 Panel end B D Guide Rail Bracket (2) R Glass-to-Rail Bracket (16) *right-hand door installation shown. E G O R W E G D I R B D Lower guide rail W Raise guide rail www.woodbridgebath.
WOODBRIDGE a. 2 R 14 7.Slide the Guide Rail Bracket (2) against the wall, outline the Guide Rail Brackets position on the wall. Set the Stationary Glass (14) aside. Remove the Wall Bracket from the guide rail bracket and place them to the outlined positions and mark the drilling holes on the wall. Outline the position of the Bottom Clamp (13) on the base as well. Remove the Clamp from the Stationary Glass and place it back to the outlined positions, now mark the drilling holes on the threshold. b.
WOODBRIDGE R 8. Drill the holes to the wall per the predrilled position using 8mm(5/16") drill bit and apply silicone into the holes, insert the Wall Anchors (12). Mount the Wall Bracket of the Guide Rail Bracket (2) to the wall by using the Screws M5×60 (15). Drill the holes to the threshold per the predrilled poistion using 8mm (5/16”) drill bit and apply silicone into the holes, insert the Wall Anchor, mount the Bottom Clamp Plate to the threshold by using M4x30 screw (10) Please see Fig 8 for details.
WOODBRIDGE R a. 21 5 Attention: Need to loose the small allen screws before loosing the long allen screw on the roller 9. Attach the two Roller Assemblies (5) to the Glass Door(7) with the wheels facing outside of the shower. Please see Fig 9 for details b. 7 c. 7 5 5 Fig9 Attention: DO NOT attach the handle to the Door Glass until instructed. DO NOT attempt to lift the Glass Door with the handle as this may result in damage to the glass and/or serious personal injury.
WOODBRIDGE R 10. Place the Stationary Glass Assembly back into the designated position. Slide the Guide Rail Bracket (2) to the two end sides of the Upper Guide Rail(4). Tighten the set screws on the Guide rail bracket (2) with Allen Key (18) to secure the guide rail to the wall. Install the Bottom Clamp (13) back to the Stationary Glass(14). Please see Fig 10 for details. a. Note: 2 b. 2 The other side of the Guide Rail bracket (2) is installed in the same way. c. d. e. f. 16 Fig10 www.
W WOODBRIDGE R R 2 a. E G 14 D I R B D O O W b. W D O 14 R E G D I R B D Door end O O W Guide Rail Bracket (#2) Fig 11 Lower guide rail O W Panel end R D O O W Glass-to-Rail Bracket (16) *right-hand door installation shown. E G B D I R Raise guide rail www.woodbridgebath.
WOODBRIDGE R 12. Place the Guide Block(11) to the bottom edge of the Stationary Glass(14), mark down the predrilled position of the guide block. Now drill the hole with 3.2mm(Ø 1/8")drill bit to the threshold. Put the silicone to the hole and then put the Wall Anchor (12) into the hole. Now secure the Guide Block to the threshold with M4x30 screw (10). Fig12 Please see Fig 12 for details www.woodbridgebath.
WOODBRIDGE R Fig12 www.woodbridgebath.
WOODBRIDGE R (X) X 9 Fig13 13.Measure the distance “X” from the Stationary Glass(14) to the wall. Cut the Anti-Splash Threshold(9) to the length of “X” if necessary. www.woodbridgebath.
WOODBRIDGE R Fig14 14. Put slicone sealant to the bottom of the Anti-Splash Threshold(9), secure the threshold in front of the Glass Door. Please see Fig 14 for details www.woodbridgebath.
WOODBRIDGE R a. Fig15 15. Hang the Glass Door (7) back to the Upper Guide Rail (4), slide the bottom of the glass door into the slot of the Guide Block (11). Be careful that the glass door should not touch the metal part of the guide block. Please see Fig 15 for details www.woodbridgebath.
WOODBRIDGE R Fig16 16. Hang the Glass Door(7) installed with Rollers(5) to the Upper Guide Rail(4). Use a 3/16”shim beneath the Glass Door when adjusting the level of the door so that the glass does not make contact with the guide block or threshold. The adjustment disks in the wheels are the same as the disks in the Glass-to-Rail Brackets and can be rotated to adjust the Glass Door (7) to create a seal with the wall.
WOODBRIDGE R a. 20 c. 17. Install the Safety Pin(17) to the Glass Door (7). Make sure that the clear gasket will be between the glass and the metal parts of the safety pin. Please see Fig 17 for details Inner cover Clear Gasket Washer www.woodbridgebath.
WOODBRIDGE R e. a. 1 1 11 Bottom guide block Sealing strip Inner side Moving glass WALL Statinary glass Waterproof strip Outer side 8 WALL Fig18 7 6 18.Attach the Side Anti-Water Strip (8) to the edge of the Stationary Glass (14) and the Bumper Strip to the Glass Door(7). Use a razor knife to trim the Side Anti-Water Strip(8) at the top to avoid interfering with the Upper Guide Rail(4).
WOODBRIDGE R a. b. 3 3 9/16" Moving glass outer side 3 c. 5 1/8" d. 2" minimum Fig19 19.Door Stopper Installation Measure the Glass Door Stopper(3) location and remove the set screw from the Stoppers apply Thread Lock Adhesive to the set screw threads, tighten screws into the stopper hole. Please see Fig 19 for details. www.woodbridgebath.
WOODBRIDGE R 20. Apply silicone sealant on the seams between the stationary glass and the shower base/bathtub, and between the wall and the stationary glass. See Figure 20 for details. TUB DOORS INSTALLATION the same as SHOWER DOORS Fig20 IMPORTANT: MUST ALOW SILICONE TO DRY FOR 24 HOURS BEFORE STARTING USING THE SHOWER ENCLOSURE Thank you for using WoodBridge products! Please don't hesitate to contact us if you have any questions or concerns. Customer Service Phone: 562-229-0088.