Installation Guide

ManualsBrandsWOODBRIDGE ManualsBathHarlow 43 in. W x 22 in. D Single Basin Carrara Marble Vanity Top in Carrara White with White Vitreous China Basin

WOODBRIDGE

2020910 REV. 2

VANITY TOP & SIDE SPLASH

• INSTALLATION

• CARE AND MAINTENANCE

INSTALLATION

2) Apply silicone caulk/sealant to all four corners of the vanity.

3) Place the top on the vanity base and assure it is aligned on all edges.

4) Leave for 3 hours to let the silicone set. If any warpage is obvious, put a weight

on top of a towel over the high points and leave over night for the top to settle.

100% silicone instead of plumbers putty between all rubber gaskets and O-rings.

Silicone

Figure 1

Silicone

31” vanity top with wave

bowl shown in illustration

Figure 2

INSTALLATION

2) Apply silicone caulk/sealant to all four corners of the vanity. Figure 2.

3) Place the vanity top on the vanity base and assure it is aligned on all edges.

Figure 2.

4) Put a small bead of silicone across the back side of the backsplash. Figure 2.

against the wall. Figure 3.

6) Run a small bead of silicone along the backsplash edges where it meets the wall

7) Leave for 3 hours to let the silicone set. If any warpage is obvious, put a weight

on top of a towel over the high points and leave over-night for the top to settle.

100% silicone instead of plumbers putty between all rubber gaskets and O-rings.

Silicone

31” vanity top with wave

bowl shown in illustration

Figure 3

31” vanity top with wave

bowl shown in illustration

Note: Install the side splash AFTER installing the vanity top.

2) Put a small bead of silicone across the non-polished side

of the side splash. Note: For universal side splashes, add silicone to

the desired side.

3) Place the side splash on the vanity top with its non-polished

4) Run a small bead of silicone along the side splash edges

where it meets the wall, vanity top and back splash and smooth

5) Leave for 3 hours to let the silicone set.

SIDE SPLASH INSTALLATION

WOODBRIDGE

www.woodbridgebath.com

Customer Service Phone: 562-229-0088. (Monday - Friday 9 AM - 5 PM Paciﬁc Time)

Or Email: help@woodbridgebath.com

Summary of content (3 pages)

PAGE 1
R WOODBRIDGE VANITY TOP & SIDE SPLASH • INSTALLATION • CARE AND MAINTENANCE Silicone INSTALLATION 2) Apply silicone caulk/sealant to all four corners of the vanity. 3) Place the top on the vanity base and assure it is aligned on all edges. 4) Leave for 3 hours to let the silicone set. If any warpage is obvious, put a weight on top of a towel over the high points and leave over night for the top to settle. e 100% silicone instead of plumbers putty between all rubber gaskets and O-rings.
PAGE 2
R WOODBRIDGE Silicone CARE & MAINTENANCE • Do not use water that exceeds temperatures of 140°F/46°C. • Do not place any sharp or abrasive objects on the bare surface of the top. • Clean the top and side splash only with non-abrasive cleaners or mild detergents - do not use powder cleansers. For extremely stubborn stains, use a small amount of acetone on a cloth and gently rub out the stain. Silicone Silicone Failure to follow the above instructions will void all warranty claims.
PAGE 3
I R B D INSTALACIÓN Silicona O O W 2) Aplicar masilla de silicona / sellante a las cuatro esquinas del tocador. Figura 2. 3) Coloque el lavabo sobre el tocador y asegúrese de que esté alineado en todos los bordes. Figura 2. 4) Coloque una pequeña gota de silicona en la parte posterior del respaldo. Figura 2.