INSTALLATION AND CARE GUIDE R WOODBRIDGE ELECTRONIC BIDET TOILET :B0960S Compliance with the following codes & standard: • 2015 Uniform Plumbing Code® ( UPC ) • 2018 International Plumbing Code® ( IPC ) • 2018 International Residential Code ® ( IPC ) • CSA B45.5 / IAPMO Z124-2017- Plastic Plumbing Fixtures ICC SCC Accredited CB-P/S ANSI TM ACCREDITED LISTED OCPS Accrédité CCN ISO/IEC 17065 Product Certification Body #1000 PREFERED EDUCATION PROVIDER Customer Service Phone: 562-229-0088.
R ELECTRONIC BIDET TOILET WOODBRIDGE READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT INSTRUCTIONS THAT, IF IGNORED COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING OR INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION.
R ELECTRONIC BIDET TOILET WOODBRIDGE IMPORTANT SAFEGUARDS When using electrical products, especially when children are present, basic safety precautions shouldalways be followed, including the following: 1.The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. 2.Children being supervised not to play with the appliance. 3.
R ELECTRONIC BIDET TOILET WOODBRIDGE CAUTION– Indicates that failure to follow the instruction may cause body injury or property damage. 1. Do not install or use the product in wet places as steam room etc.This product must be connected to properly grounded power outlet socket. 2. It is recommended to use water-proof electrical outlet which should be lnstalled in the place where is not easily got wet. 3.
R ELECTRONIC BIDET TOILET WOODBRIDGE Rating pressure AC 110V-120V,50/60Hz Main Unit Toilet Rating power Water pressure range Minimum water pressure 0.07MPa (20L/min. flow). Maximum water pressure 0.8MPa (Hydrostatic pressure) Electrical wire length is about 1.8m Flush volume 1.6/1.1GPF(6.0/4.1 L) Flushing mode Siphonic jet Rough in 12" Outlet outside diameter 3.
R ELECTRONIC BIDET TOILET WOODBRIDGE 1-1/8" 16" Ø1/4" 1-3/4" 11-3/4" 22-5/8" 43-1/4" 6-5/8" DIMENSIONS/TECHNICAL DATA 3-1/2" Rough-in 13" 12" Standard 15-1/8" 5-7/8" 7-1/2" 15-3/8" 11-3/4" 22-3/4" 28-3/4" IMPORTANT • Measurements are +3/8" and subject to change without notice • Please note that installer(s) must be certify or warranty will be voided.
R ELECTRONIC BIDET TOILET WOODBRIDGE DIMENSIONS/TECHNICAL DATA 28-3/4" 17-7/8" 22-5/8" 16" Ø1/4" 1-3/4" 21-5/8" 10-1/4" 22-5/8" 21-5/8" 2-1/2" 2-1/8" 16" 2-3/8" 11-3/8" 3-3/4" 13" 1.The product drawing is for reference only, and we reserve the right to modify the appearance of the product. 2.If the appearance of the product is changed, the actual product shall prevail. www.woodbridgebath.
R ELECTRONIC BIDET TOILET WOODBRIDGE Installation Option 15-3/4" 19-5/8" 15-3/4" Recommended location for remote control mounting (Left or Right) Ø1 Connect the water inlet and angle valve of the toilet with the matching hose and tighten it /4 2-3/8" angle valve " 17-7/8" new hose 16" 22-5/8" 31-1/2" water inlet 1-3/4" 20-7/8" Rough-in 12" Standard STANDARD INSTALLATION NO SHOW INSTALLATION Wall Power Outlet(GFCI) Wall Power Outlet(GFCI) Water Outlet （Angle valve mounting) Water
R ELECTRONIC BIDET TOILET WOODBRIDGE PARTS IDENTIFICATION Bumper Left side Lid Power indicator Energy saving indicator Human body sensing window Human body sensing window Remote sensing window Rear cleaning button Seat Drying button Power button Ceramic toilet Flush button Front cleaning button Water discharging Nozzle baffle Drying baffle Rear cleaning Half flush button Full flush button Front cleaning Main unit disassembly button Spray nozzle Deodorization window Remote sensing window Right
R ELECTRONIC BIDET TOILET WOODBRIDGE Installation of ceramic toilet 1.Water supply angle valve installation • Draw drain outlet centerline on the floor, install angle valve at proper position on wall according to dimension of toilet. 10" off center is preferred. Angle valve 10" 3.Mounting bracket installation • Assemble the mounting L-Bracket with bolts and then install them to the pre-install flange plate on the ground and tighten with nuts. Washer Mounting bracket Bolt Nut Line Drain outlet 4.
R ELECTRONIC BIDET TOILET WOODBRIDGE 6.Installation of hose Plastic Insert •Connect water inlet and angle valve with new hose. Screw Decorative cap Install Screw through Plastic Insert and into the opening on the side of the toilet. Tighten Screw into L-Bracket being careful not to over tighten. 5.Silicone caulking application • Apply Silicone caulking to the edge of toilet base, wipe away any excess.
R ELECTRONIC BIDET TOILET WOODBRIDGE Before Installation 1.Turn on the angle valve Check thread connection,make sure no leakage is found. Angle valve 2.Power Connection Insert power line leakage protection plug into the power socket, press the reset switch, plug indicator lights on indicating that the power is on. Tips: Press electric leakage test button prior to usage, the reset switch pops up indicating that the leakage protection function is normal.
R ELECTRONIC BIDET TOILET WOODBRIDGE Daily maintenance Main unit care and maintenace Spray nozzle maintenance and care 1.Shut off power supply at maintenance. 2.Turn the seat upward open, press down the button located on the right side of main unit and pull out the seat.Wipe the stain with a soft damp cloth. 1.Nozzle self-cleaning Press “nozzle cleaning” button and nozzle will move forward and self-clean. 2.Spray nozzle disassemble When the wand moves forward,the nozzle can be disassembled to clean.
R ELECTRONIC BIDET TOILET WOODBRIDGE Emergency Troubleshooting Electricity and water supply cut-off 1. Power failure •Manually press button of full/half flush to perform the toilet flushing. Operation panel 2.Water failure •Put around 8L water into a barrel and flush the bowl of ceramic. Note:Avoid water spilling from bowl. Barrel Newspaper 13 www.woodbridgebath.
R ELECTRONIC BIDET TOILET WOODBRIDGE Failure of remote control When the product is left unused for long time 1.Operate the panels on bidet seat to perform. •Especially in winter season,the water inside the tank should be discharged to avoid freezing. To discharge water 1.Turn off the water supply angle valve 2.Cut off the electricity 3.Discharge water •Slightly press inward the discharging button to discharge water. 2.
R ELECTRONIC BIDET TOILET WOODBRIDGE The illustration of main unit keys Power 1. Long press "power" button to enter standby mode; and then quick press "power" button to restore functional mode. 2. When people sit, press "power" button to stop the function of rear, front cleaning or drying. When no one sits, press "power" button to switch between function mode and power save mode. Flush Press "flush" button to activate full flushing. Dry Press "dry" button, warm wind will come out.
R ELECTRONIC BIDET TOILET WOODBRIDGE Troubleshooting Guide Problem No flushing Poor flushing Solution Cause water supply hose buckling causes block solve the buckling fill valve is off turn on the fill valve Water supply is cut off Connect water supply and wait for the water Water supply hose buckling causes partial block Fill valve is not fully turned on Filter is dirty and causes block Solve the buckling Fully turn on the fill valve Clean the filter The water is not hot The water temperature is
R ELECTRONIC BIDET TOILET WOODBRIDGE Produdct Limited Warranty Thank you for choosing out product. This product is warranted for one(1)years since the purchasing date for free repair of problems arising out of defects in workmanship while using in accordance with installation manual and usage cations for intended purposes. lf the product does not work properly with warranty period, please contact your nearest service center. This certificate must be presented to obtain free service under this warranty.
www.woodbridgebath.
Thank you for using WoodBridge products! Customer Service Phone: 562-229-0088. (Monday - Friday 9 AM - 5 PM Pacific Time) Or Email: help@woodbridgebath.com www.woodbridgebath.
