Welcome to the breezy life.
Safety first A few things before you get started: General Installation Warnings & Cautions Installing your Windmill AC should take about 45 minutes If you’re looking for professional assistance, we have some options for you: windmillair.com/support We recommend doing this with a helper We’re here if you need us, so don’t hesitate to chat or email: windmillair.
Window Requirements What’s in the box? SMALL STUFF The Windmill AC The Windmill AC is designed for windows that slide up and down (double-hung windows) with a width of 23-37 inches and a vertical opening of at least 14 inches. To simplify your setup, the AC comes with the top and bottom install bars, the front frame, side adapters, and both side panels pre-assembled.
Step 1 Insulate your window. WHAT YOU NEED 6 Flip to view steps.
Step 1. Insulate your window. 1 2 3 4 x y Cut the adhesive foam to the width of your window. Stick the adhesive foam across the underside of the front window sash.** Cut the non-adhesive foam to the height Insert the foam into the channels on of the bottom half of your window. both sides. You should cut the foam to be the width of your window from the left to the right side. Make sure you’re cutting the foam with the adhesive. Peel off the backing paper to expose the adhesive.
Step 2 Lift the AC into the window. WHAT YOU NEED 10 Flip to view steps.
Step 2. Lift the AC into the window. 1 2 Wooden Windows 3 Vinyl Windows Inside Inside Outside Inside Outside Outside Together with your helper, lift the assembled AC into the window frame. Properly position the bottom bar BEHIND the inside window sill. Close the window down onto the AC, BEHIND the top bar. Make sure you do this step with a helper. Very carefully, lift the assembled AC into the window frame.
Step 3 Secure the AC. WHAT YOU NEED 14 Flip to view steps.
Step 3. Secure the AC. 1 2 3 Use the side panels to fit the AC to the window. Secure the AC using the included 1/2 inch screws. Fill the center hole on the front frame with the included rubber plug. Extend the side panels out until they reach the window frames on each side. Now that your AC is in the right position, you’ll need to secure it using the included ½ inch screws. Locate the five screw hole locations on the unit and side panels as marked.
Step 4 Cut and attach the cosmetic panels. WHAT YOU NEED 18 Flip to view steps.
Step 4. Cut and attach the cosmetic panels. 1 2 3 4 Determine the width of your side panels. Find the corresponding number on your cosmetic panels. Insert the trimmed side panels into the front frame. Snap the prongs into place. This is the number on your side panel that falls just behind the edge of the front frame. (Make sure you are using the correct panel. They are labeled “Left” and “Right”) Snap the three prongs into the corresponding slots on the ends of the side panels.
Step 5 Lock and insulate your window. WHAT YOU NEED 22 Flip to view steps.
Step 5. Lock and insulate your window. 1 2 3 x Option 1: Wood windows. Option 2: Vinyl windows. Cut the non-adhesive insulation foam to fit the width of your window. Use the nonadhesive foam to fill the gaps in your window. Attach the sash lock as shown in the diagram above. Attach the sash lock as shown in the diagram above. Make sure you are cutting the foam with the non-adhesive sides. Measure and cut the foam to be the width of your window from the left to right side.
Some other things you may want to know. 1 2 Connect your Windmill AC to your smartphone. How to help the environment and save on your energy bill: To learn how to connect your Windmill AC to your smartphone and for app related questions, please go to windmillair.com/support. ● ● ● ● ● 3 To remove your AC from the window: Clean your large mesh filter at least monthly (and if applicable, replace your activated carbon filter every 2-4 months). Make sure nothing is blocking the air flow around your AC.
windmillair.
