Instructions / Assembly

ManualsBrandsWilliams ManualsGarden CenterBlower Accessory for Console Room Heaters

2102 Blower Accessory

Installation & Operating Instructions

WARNING

Danger of property damage, bodily injury or death.

Turn off electrical power supply at disconnect switch, fuse box or service panel before removing or working on fan.

Switch Mounting Bracket Installation

The switch mounting BRACKET installation is not required on the 350 Series Models. If your model is a 350 Series Model, skip to

“Mounting the Blower” on page 3 of these instructions. The two mounting BRACKETS shown below may be discarded if you are

installing this blower on a 350 Series Model. Installation of the correct fan switch mounting BRACKET will assure accurate operation of

the automatic fan.

1. Locate the fan switch and remove the two (2) screws that hold the fan switch mounting PLATE to the fan assembly.

2. Gently pull fan switch wires from the junction box to extend black wires.

3. Place fan switch wires on switch mounting BRACKET (smaller sized bracket for 500 Series

Models; larger sized BRACKET for the 650 Series Models). The metal switch needs to face

away from bracket. Lay switch wires flat on mounting BRACKET and align top of fan switch

with top of bracket.

For use with:

Switch Mounting BRACKET

650 Series Models

Part No. K000870

Switch Mounting BRACKET

500 Series Models

Part No.

K000868

Switch Mounting PLATE

Part No.

350 Series Models

3501521, 3501522

3501921, 3501922

3502521, 3502522

3502921, 3502922

500 Series Models

5001521, 5001522

5001921, 5001922

5002521, 5002522

5002921, 5002922

650 Series Models

6501521, 6501522

6501921, 6501922

6502521, 6502522

6502921, 6502922

Summary of content (4 pages)

PAGE 1
2102 Blower Accessory Installation & Operating Instructions For use with: 350 Series Models 500 Series Models 650 Series Models 3501521, 3501522 3501921, 3501922 3502521, 3502522 3502921, 3502922 5001521, 5001522 5001921, 5001922 5002521, 5002522 5002921, 5002922 6501521, 6501522 6501921, 6501922 6502521, 6502522 6502921, 6502922 WARNING Danger of property damage, bodily injury or death.
PAGE 2
4. Replace switch mounting PLATE on switch BRACKET using the screws removed in Step 1 above. Switch Mounting Positions 500 Series EVEN with the top of the switch mounting BRACKET 650 Series ABOVE the top of the switch mounting BRACKET 5. Ensure that fan switch is facing away from fan assembly and even with top of switch MOUNTING bracket. 500 Series 6. 650 Series Attach switch mounting BRACKET to outside of fan assembly using the two (2) screws provided.
PAGE 3
Mounting the Blower Note: All electrical work must conform to your local codes and ordinances or in their absence, with National Electrical Code, ANSI/NFPA 70. If you are not familiar with wiring codes in general, have a competent electrician do this job. In CANADA: CANADIAN ELECTRICAL CODE C22.1. WARNING Danger of property damage, bodily injury or death. Turn off electrical power supply at disconnect switch, fuse box or service panel before removing or working on fan. 1.
PAGE 4
Operation This accessory is operated using the factory equipped, three-prong (grounding) plug and cord. When using the plug and cord, for your protection against shock hazard, it must be plugged directly into a properly grounded three-prong receptacle. DO NOT CUT OR REMOVE THE PRONG. You must select “HI” or “LO” on the speed switch (item 8) for automatic blower operation. When the heater heats up, the fan switch is activated and the blower will operate. When the heater cools down, the blower will turn off.