Use and care guide
6
When installing the appliance
make sure that the four feet are
stable and resting on the oor,
adjusting them as required,
and check that the appliance is
perfectly level using a spirit
level.
In the case of installation on
wood or oating oors,
position the washer dryer on a
plywood panel that has been
xed to the oor, which must
be at least 60 x 60 cm in size,
and at least 3 cm thick.
Use only new hoses to connect
the appliance to the water
supply. Used hoses must not
be used and should be
discarded.
Do not move the washer dryer
while holding onto its upper
surface.
Connect the water inlet hose(s)
to the water supply in
accordance with the
regulations of your local water
company.
For models dedicated only for
cold water: Do not connect to
the hot water supply.
For models with hot ll: the hot
water inlet temperature must
not exceed 60°C.
Make sure that the ventilation
openings in the base of your
appliance (if available on your
model) are not obstructed by a
carpet or other material.
The supply water pressure
must be in range 0.1 -1 MPa.
The appliance must not be
installed in such a way as to
impede its door from opening
completely (e.g. behind a
lockable door, a sliding door, or
a door that is hinged on the
side opposite to that of the
appliance itself).
ELECTRICAL WARNINGS
Make sure the voltage
specied on the rating plate
Do not stop the appliance until
the drying cycle has been
completed;if this should be
necessary, quickly remove all
the garments and lay them out
in order to facilitate the heat's
dissipation.
The last phase of the drying
cycle is done without heat
(cool down phase), to assure
that the laundry stays at a
temperature level which is not
leading to a damaging of the
laundry.
INTENDED USE OF THE
PRODUCT
This appliance is designed
solely for domestic usage. To
aim the appliance as
professional use is forbidden.
The manufacturer declines all
responsibility for inappropriate
use or incorrect setting of the
controls.
CAUTION : The appliance is
not intended to be operated
by means of an external timer
or separate remote control
system.
Do not use the appliance
outdoors.
Do not store explosive or
ammable substances such as
aerosol cans and do not place
or use gasoline or other
ammable materials in or near
the appliance: a re may break
out if the appliance is
inadvertently switched on.
This appliance is designed
exclusively for domestic use
with loads of laundry that can
be washed and spun in a
washer dryer machines.
INSTALLATION
Installation and repairs must
be carried out by a qualied
technician, in compliance with
the manufacturer’s instructions
and local safety regulations. Do
not repair or replace any part
of the appliance unless
specically stated in the user
manual.
Children should not perform
installation operations. Keep
children away during
installation of the appliance.
Keep the packaging materials
(plastic bags, polystyrene
parts, etc.) out of reach of
children, during and after the
installation of the appliance.
Use protective gloves to
perform all unpacking and
installation operations.
After unpacking the appliance,
make sure that it has not been
damaged during transport. In
the event of problems, contact
the dealer or your nearest
Customer Support Service.
The appliance must be
handled and installed by two
or more persons.
Keep children away during
installation of the appliance.
The appliance must be
disconnected from the power
supply before carrying out any
installation operation.
During installation, make sure
the appliance does not
damage the power cable.
Only activate the appliance
when the installation
procedure has been
completed.
After installation of the device
to wait a few hours before
starting it, to acclimatise to the
environmental conditions of
the room.
Do not install your appliance
where it may be exposed to
extreme conditions, such as:
poor ventilation, temperature
below 5°C or above 35°C.