Installation Instruction

ManualsBrandsWhirlpool ManualsHousehold Appliance7.0 cu. ft. Electric Dryer with Steam in White

W11101341A

W11101343A-SP

DRYER SAFETY ............................................................... 2

INSTALLATION REQUIREMENTS ................................... 4

Tools and Parts ..................................................................... 4

LOCATION REQUIREMENTS .................................................... 5

ELECTRICAL REQUIREMENTS ................................................ 6

INSTALL LEVELING LEGS ......................................................... 7

ELECTRICAL CONNECTION .................................................... 8

VENTING ......................................................................... 13

Venting Requirements ........................................................ 13

Plan Vent System ................................................................ 14

Venting Kits ......................................................................... 15

Install Vent System ............................................................. 16

CONNECT INLET HOSES ........................................................ 16

CONNECT VENT ...................................................................... 17

LEVEL DRYER .......................................................................... 18

COMPLETE INSTALLATION CHECKLIST .............................. 18

REVERSE DOOR SWING (OPTIONAL) ................................... 18

TROUBLESHOOTING ...........................................BACK COVER

ELECTRIC DRYER INSTALLATION INSTRUCTIONS

29" WIDE MODELS – U.S.A. ONLY

Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su producto, visite:

www.whirlpool.com

Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad superior de la puerta.

Table of Contents

Summary of content (20 pages)

PAGE 1
ELECTRIC DRYER INSTALLATION INSTRUCTIONS 29" WIDE MODELS – U.S.A. ONLY Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su producto, visite: www.whirlpool.com Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad superior de la puerta. Table of Contents DRYER SAFETY................................................................ 2 INSTALLATION REQUIREMENTS....................................
PAGE 2
DRYER SAFETY 2
PAGE 3
PAGE 4
INSTALLATION REQUIREMENTS Parts supplied (all models): Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed: Leveling legs (4) Parts package is located in dryer drum. Check that all parts are included.
PAGE 5
LOCATION REQUIREMENTS Side View 223/4" (578 mm) 273/4" (705 mm) 273/4" (705 mm) 133/4" (349 mm) A B A. Wide opening side-swing door B. Wide opening hamper door You will need: ■■ A location allowing for proper exhaust installation. See “Venting Requirements.” ■■ A separate 30 amp circuit. ■■ If you are using power supply cord, a grounded electrical outlet located within 2 ft. (610 mm) of either side of dryer. See “Electrical Requirements.
PAGE 6
Electrical Connection Minimum Required Spacing 3" (76 mm) 14" max. (356 mm) 48 in.2 (310 cm2) 18" (457 mm) 24 in.2 (155 cm2) 51/2" (140 mm) 1" (25 mm) 1" (25 mm) 3" (76 mm) Mobile home – Additional installation requirements This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280).
PAGE 7
2. Screw in leveling legs Using a wrench and tape measure, screw legs into leg holes until bottom of foot is approximately 1/2" (13 mm) (to match height of 3.6 cu. ft. capacity washer) or 1½" (38 mm) (to match height of 3.8 cu. ft. capacity washer) from bottom of dryer. Now stand the dryer on its legs. Slide the dryer until it is close to its final location. Leave enough room for electrical connection and to connect the exhaust vent. INSTALL LEVELING LEGS 1.
PAGE 8
ELECTRICAL CONNECTION Power Supply Cord Direct Wire Electrical Connection Options 1. Choose electrical connection type Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to steps 1–2 on page 9 for power supply cord strain relief: then steps 3–6 for “4-wire Power Supply Cord Connection” section. Then, go to “Venting Requirements.” 2.
PAGE 9
Power Supply Cord Connection 3. Prepare to connect neutral Power supply cord strain relief ground wire and neutral wire 1. Attach power supply cord E strain relief A A B B C D Remove center terminal block screw (B). Remove neutral ground wire (E) from external ground conductor screw (A). Remove the screws from a 3/4" (19 mm) UL Listed strain relief.
PAGE 10
5. Connect remaining wires 6. Connect remaining wires Connect remaining wires to outer terminal block screws. Tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to “Venting Requirements.” Connect remaining wires to outer terminal block screws. Tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to “Venting Requirements.
PAGE 11
4-wire Direct Wire Connection IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit 3-wire connections. 6. Connect neutral ground wire and neutral wire 3. Prepare your 4-wire cable for E C direct connection 31 ⁄2" ) m (89 m 1" ) m (25 m B (127 5" mm ) Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed. Strip 5" (127 mm) of outer covering from end of cable, leaving bare ground wire at 5" (127 mm).
PAGE 12
3-wire Direct Wire Connection Use where local codes permit connecting cabinet-ground conductor to neutral wire. 6. Connect neutral wire C 3. Prepare your 3-wire cable for direct connection 1" ) m (25 m B 3½ (89 m " m) Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved, if needed. Strip 31/2" (89 mm) of outer covering from end of cable. Strip insulation back 1" (25 mm). If using 3-wire cable with ground wire, cut bare wire even with outer covering.
PAGE 13
VENTING 2. C onnect neutral ground wire Venting Requirements and neutral wire E C B Connect neutral ground wire (E) and neutral wire (white or center wire) (C) of power supply cord or cable under center terminal block screw (B). Tighten screw. WARNING: To reduce the risk of fire, this dryer MUST BE 3. Connect remaining wires EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances. ■■ Following these venting requirements will minimize ducting air noise.
PAGE 14
Exhaust hoods: ■■ Must be at least 12" (305 mm) from ground or any object that may obstruct exhaust (such as flowers, rocks, bushes, or snow). Recommended Styles: Plan Vent System Recommended exhaust installations Typical installations vent the dryer from the rear of the dryer. Other installations are possible. B C D E Louvered hood Box hood F A G Acceptable Style: B H A. B. C. D. Angled hood Elbows: ■■ 45° elbows provide better airflow than 90° elbows.
PAGE 15
Alternate installations for close clearances Venting systems come in many varieties. Select the type best for your installation. Two close-clearance installations are shown. Refer to the manufacturer’s instructions. Special provisions for mobile home installations: The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside.
PAGE 16
Vent System Chart (Long Vent Models Only) Number of 90° turns or elbows Type of vent Box/louvered, or Angled hoods 0 Rigid metal 120 ft. (36.6 m) 1 Rigid metal 110 ft. (33.5 m) 2 Rigid metal 100 ft. (30.5 m) 3 Rigid metal 90 ft. (27.4 m) 4 Rigid metal 80 ft. (24.4 m) 5 Rigid metal 70 ft. (21.3 m) CONNECT INLET HOSES (Steam Models Only) For non-steam models, skip to “Connect Vent.” The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. 1.
PAGE 17
4. Attach long hose to “Y” connector and tighten couplings Attach dryer 5 ft (1.5 m) inlet hose ends to the “Y” connector. Attach washer cold inlet hose to other side of “Y” connector. Screw on coupling by hand until it is seated on connector. Using pliers, tighten the couplings an additional two-thirds turn. NOTE: Do not overtighten. Damage to the coupling can result. 5. Attach long hose to dryer fill 7. Check for leaks Check for leaks around “Y” connector, faucet, and hoses. CONNECT VENT 1.
PAGE 18
LEVEL DRYER q q q 1. Level Dryer Check levelness of dryer from side to side. Repeat from front to back. NOTE: The dryer must be level for the moisture sensing system to operate correctly. Not Level LEVEL Not Level 2. Tighten and adjust leveling legs Be sure the water faucets are on. Check for leaks around “Y” connector, faucet, and hoses. If you live in a hard water area, use of a water softener is recommended to control the buildup of scale through the water system in the dryer.
PAGE 19
3. Lift door off top screws 6. Switch door catch, bezel, and plug Catch and bezel Plug Lift door until top screws in dryer cabinet are in large part of hinge slot. Pull door forward off screws. Set door (handle side up) on top of dryer. Remove top screws from dryer cabinet. 4. Remove screws from hinges Remove the door catch, bezel, and plug from the inside of the inner door by squeezing and pulling/pushing them. Place the door catch, bezel, and plug on the sides opposite from where they were. 7.
PAGE 20
11. Remove and transfer 9. Attach door hinges hinge hole plugs Use a small, flat-blade screwdriver to gently remove four hinge hole plugs on left side of dryer cabinet. Transfer plugs into hinge holes on opposite side of dryer cabinet. 12. Insert screws in hinge holes on dryer cabinet Reattach door hinges to dryer door so that the larger hole is at the bottom of the hinge. 10. Remove door strike and door strike plug Door strike Door strike plug NOTE: Two people may be needed to reinstall door.