Range Hood Installation Instructions and Use & Care Guide

8
Wall Venting
To make a 4" x 10½" (10.2 cm x 26.7 cm) rectangle in the wall:
1. Make 2 lines by measuring from floor 65⁷⁄₈" (167.3 cm) and
62³⁄₈" (158.4 cm) or ¹⁄₈" (3.2 mm) and 3⁵⁄₈" (9.2 cm) down from
underside of cabinet and mark on the centerline on the back
wall.
2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline
on the wall.
3. Use saber or keyhole saw to cut a rectangular opening in the
wall for the vent.
Style 2 - Cut Openings for 7" (17.8 cm) Round Vent
System
Roof Venting
To make a 7¹⁄₄" (18.4 cm) circle on the underside of the cabinet
top and bottom:
1. Mark a centerline on the underside of the cabinet bottom.
2. Mark a line 5" (12.7 cm) from the back wall on the underside
of the top of cabinet.
3. Draw a circle using a compass or 7¹⁄₄" (18.4 cm) circle
template.
4. Use saber or keyhole saw to cut a 7¹⁄₄" (18.4 cm) diameter
opening.
5. Repeat steps 1-4 for the underside of the top of the cabinet.
Style 3 - Cut Openings for 3¼" x 10" (8.3 x 25.4 cm)
Rectangular Vent to 7" (17.8 cm) Round Vent Transition
Roof Venting
To make a 4" x 10½" (10.2 x 26.7 cm) rectangular cutout on the
underside of cabinet bottom:
1. Mark lines 1½" (3.8 cm) and 5½" (14.0 cm) from the back wall
on the centerline of the underside of cabinet.
2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline
on the underside of cabinet.
3. Use saber or keyhole saw to cut a rectangular opening for
vent.
To make a 7¹⁄₄" (18.4 cm) circle on the underside of the cabinet
top:
1. Mark a centerline on the underside of the top of cabinet.
2. Mark a line 5" (12.7 cm) from the back wall on the underside
of the top of cabinet.
3. Draw a circle using a compass or 7¹⁄₄" (18.4 cm) circle
template.
4. Use saber or keyhole saw to cut a 7¹⁄₄" (18.4 cm) diameter
opening.
Install Vent System
1. Install vent through the vent opening in upper cabinet or wall.
Complete venting system according to the selected venting
method. See “Venting Requirements” section.
2. Use caulking to seal exterior wall or roof opening around the
cap.
¹⁄₈"
3 ⁵⁄₈"
Cabinet
front
5
¹⁄₄"
(3.2 mm)
(9.2 cm)
(13.3 cm)
Centerline
7 ¹/₄" (18.4 cm) diam.
c
abinet cutouts
*From wall, not
cabinet frame
*5"
(12.7 cm)
5¹/₄"
(13.3 cm)
5¹/₄"
(13.3 cm)
*5¹/₂"
(14 cm)
*From wall, not cabinet frame
*1¹/₂" (3.8 cm)
7
¹/₄" (18.4 cm) diam.
Cabinet
cutouts
*From wall, not
cabinet frame
*5"
(12.7 cm)