Setup and user guide

ManualsBrandsWhirlpool Manualskitchen & houseware accessoriesSMC 653 F/BT/IXL

Quick guide

PRODUCT DESCRIPTION

THANK YOU FOR PURCHASING A WHIRLPOOL

PRODUCT

To receive more comprehensive help and support,

please register your product at www.whirlpool.eu/

Before using the appliance carefully read the Health and

Safety guide.

USING THE APPLIANCE FOR THE FIRST TIME

SETTING THE POWER

At the time of purchase, the hob is set to the maximum possible power

(nL). The maximum power level (nL) is printed on the identication

plate on the bottom of the hob.

To set the power of the hob:

Once you have connected the device to the mains power supply, you

can set the power level within 60 seconds.

Press the

button for at least 3seconds.On the screen, the

symbol will be displayed.

Press the

button until the last power level selected appears.

Use the

and buttons to select the desired power level. The

power levels available are: 2.5 kW - 4.0 kW - 6.0 kW – nL (no limit).

Conrm by pressing

The power level selected will stay in the memory even if the power

supply is interrupted.

To change the power level, disconnect the appliance from the mains

for at least 60 seconds, then plug it back in and repeat the steps above.

If an error occurs during the setting sequence, the

symbol will

appear, and you will hear a beep. If this happens, repeat the operation.

If the error persists, contact the After-Sales Service.

TURNING THE BEEP ON/OFF

To activate/deactivate the beep:

Switch on the hob

Press the

button on the rst left-hand slide touchscreen for

3seconds.

Any alarms set will remain active.

Only use pots and pans made from ferromagnetic

material which are suitable for use with induction

hobs. To determine whether a pot is suitable, check

for the

symbol (usually stamped on the bottom).

A magnet may be used to check whether pots are

magnetic.

The quality of the pots and pans used may aect performance and

cooking results.

Empty pots or pots with a thin base

Do not use empty pots or pans when the hob is on. The hob is

equipped with an internal safety system that constantly monitors

the temperature, activating the "automatic o" function where high

temperatures are detected. When used with empty pots or pots with

thin bases, the temperature may rise very quickly, and the "automatic

o" function may not be triggered immediately, damaging the pan or

the hob surface. If this occurs, do not touch anything, and wait for all

components to cool down.

If any error messages appear, call the service centre.

Minimum diameter of pot/pan base for the dierent cooking areas

1. Identifying the cooking zone

2. Cooking zone o button

3. Cooking level selected

4. Indicator light - function active

5. Quick heat button

6. Special function indicators

7. On/ o button

8. Cooking time indicator

9. 6

Sense button (special functions)

10. OK/ Key lock button - 3 secs

11. Slide touchscreen

12. Vertical exible zone button

13. Timer

14. Timer indicator

POTS AND PANS

CONTROL PANEL

Summary of content (4 pages)

PAGE 1
IT Quick guide THANK YOU FOR PURCHASING A WHIRLPOOL PRODUCT To receive more comprehensive help and support, please register your product at www.whirlpool.eu/ register Before using the appliance carefully read the Health and Safety guide. PRODUCT DESCRIPTION USING THE APPLIANCE FOR THE FIRST TIME SETTING THE POWER At the time of purchase, the hob is set to the maximum possible power (nL). The maximum power level (nL) is printed on the identification plate on the bottom of the hob.
PAGE 2
SWITCHING THE HOB ON/OFF To turn the hob on, press the power button for around 1 second. To turn the hob off, press the same button again, and all cooking zones will be deactivated. POSITIONING Locate the desired cooking zone by referring to the position symbols at the side of each slide touchscreen. Do not cover the control panel symbols with the cooking pot.
PAGE 3
IT MAINTENANCE AND WARNING • Do not use steam cleaning equipment. • Before cleaning, make sure the cooking zones are switched off and that the residual heat indicator (“H”) is not displayed. Important: • • • • • • • Do not use abrasive sponges or scouring pads as they may damage the glass. After each use, clean the hob (when it is cool) to remove any deposits and stains from food residue. Sugar or foods with a high sugar content can damage the hob and must be immediately removed.
PAGE 4
You can download the Safety Instructions, User Manual and product card, which includes the key energy data, in the following ways: • By visiting our website at http://docs‌.‌whirlpool‌.‌eu • By using the QR Code • Alternatively, contact our Client After-sales Service (details can be found in the Warranty Booklet). When contacting our Client After-sales Service, please state the codes provided on your product’s identification plate.